Home Decorators Collection 1007581501 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) Do not use this product outdoors.
c) This seasonal use product is not intended for permanent installation
or use.
d)Donotmountorplaceneargasorelectricheaters,fireplace,candles
or other similar sources of heat.
e) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
f) Do not use this product for other than its intended use.
g) Do not hang ornaments or other objects from cord, wire, or light
string.
h) Do not cover the product with cloth, paper or any material not part of
the product when in use.
i) This product has polarized plug (one blade iswider than the other)
asa feature to reduce the risk ofelectricalshock.This plugwill fit in a
polarizedoutlet onlyoneway. Iftheplug does notfitfully in theoutlet,
reverse the plug. If it still does not fit, contact a qualified electrician.
Do not use with an extension cord unless plug can be fully inserted.
Do not alter or replace the plug.
j)This product is equipped with push-in type lamps. Do not twistlamps.
k) This product employs overload protection (fuse). A blown fuse
indicatesan overload or short-circuit situation. If the fuse blows, unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
l) Read and follow all instructions that are on the product or provided
with the product.
m) SAVE THESE INSTRUCTIONS.
CAUTION!– ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ASSEMBLING OR DISASSEMBLING.
7.5ft Brookside Fraser Fir LED Tree
SKU# 1007581501
Package Contents
A. Top Section
Qty: 1
B. MiddleSection
Qty:1
C. BottomSection
Qty:1

D. Stand with an eye
bolt
Qty:1
E. Power Cord
Qty:1

F. Remote Control
Qty: 1
G. Fuse
Qty:1
H. Rivet
Qty:2


I. Replacement
Bulb
Qty: 8
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2. Open thestand to a 90 degreeangleuntil the hole linesup with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
Assembling the tree
Pleaseremoveprotectivecoversfromthe baseofthepoleforeachtree
section before assembling.
Step1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step2.Insertthemiddlesection(B)ofthetreeintothebottomsection(C).
(See Fig. 2)
Step 3. Insert the top section (A) into the middle section (B). (See Fig. 3)
Pre-Assembly
Assembly

Step 4. Allow branches to fall into place or gently pull branches up and
out. When adjusting branches be sure that all wires are free of
branch hinges. (See Fig. 4)
Step 5. Shape the branches. Starting with tips closest to the pole,
shape one tip to the right, one to the left and one at the center
ofthemain stem.Repeatpattern foreach branch. (SeeFig.5)
Step 6. Plug the well-connected power cord from the tree section (C)
into a proper outlet. Please note this tree comes with a foot
pedal switch and remote control for easy illumination and
changingfunctions.ThistreeisColorChanging,the8lighting
options available are:
1. Steady Warm White
2. Flashing Warm White
3. Fade In and Fade Out Warm White
4. Steady Multicolor
5. Flashing Multicolor
6. Fade In and Fade Out Multicolor
7. Sequential Multicolor & Warm White
8. Color Changing
These functions can be changed by pressing the foot pedal
switch or using the remote control. Please see the
instructions of remote control below.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. Press Fn button, the function below cycle. Press thenumber key,
select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function2: Flashing Warm White
Function3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function5: Flashing Multicolor
Function6: Fade In and Fade Out Multicolor
Function7: Sequential Multicolor & Warm White
Function 8: Color Changing
There is memory modeon function adjustment.
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replacewithanewbuttoncell“CR2025”(3volt)into
the compartment.
CAUTION: DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
Turning on the tree
Step 1. Plug the well-connected power cord from the tree section (C)
into a proper outlet.
User Servicing Instructions
Replace the fuse.
a) Graspplug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover on
top of attachment plug towards blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided
with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
a) Graspplugandremovefromthereceptacleorotheroutletdevice.Do
not unplug by pulling on cord.
b) Pull lamp and plastic base straight out of lampholder.
c) Replace lamp with 3.0 volt, 20 mA type lamp(provided with product).
d) Lock the LED bulb.
CAUTION
1. To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0 Volt, 20 mA LED lamps only.
2. Riskoffire.Thisproductdoesnotcontainlampshunts,whichallowthe
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1. Pull the reflector out.
2. Remove the base of burned out
lamp by straightening lamp leads
and gently pulling lamp out.
3. Thread leads of new lamp through hole in old base with one lead in
each hole.
4. Afterlamp is fullyinserted, bend eachlead up, likeother lamps in the
light set so that the leads will touch the contacts inside the
lampholder.
Operation
Maintenance

CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE AND BULB
REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet.
Step3. Gentlylift thetreetopstraight uptoremovefromthe centersection
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step5. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Use and Care Instructions
a) Before using or reusing, inspect product carefully. Discard any
productsthathavecut,damaged,orfrayedwire insulationorcords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
b) When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to avoid
any undue strain or stress onthe product conductors, connections,
and wires.
c) When not in use, store neatly in a cool, dry location protected from
sunlight.
CAUTION
a) Toreduce theriskof electricshock,use only with the power-supply
cord provided or with a cord set intended for indoor use.
b) Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c) Donotabusecord–Donotcarryproductbythecordoryankorpull
it to disconnect from the outlet.
d) Disconnect the product from the outlet when not in use.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well. Make sure the plug of power supply
extension cord from the bottom section (C) is securely
inserted into a working electrical outlet.
Check for blown fuses at the power cord plug. Replace
as needed with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-800-986-3460 for instructions.
Loose branches
If a branch of the tree falls off, follow the steps below to reinstall it with a
spare rivet (H).
1) Place the branch into the slot of the bracket.
2) Insert a spare rivet through
the hole and use diagonal
pliers (not included) to crimp
the rivet. (See Fig. A)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Warning: Please note that changes or modifications
of this product is not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician
for help.
WARRANTY
3-year Limited Warranty
This product carries a three (3) year warranty against defects
in workmanship and materials. This product is not
guaranteed against wear or breakage due to misuse and/or
abuse.
Date Code: 05012022_2003186
Importer: The Home Depot
Address: 2455 PACES FERRY ROAD ATLANTA, GA 30339
Tel: [phone]
Model No. LTW39-3