Home Easy HE-106 User manual

1 65432
12 3 4 5 6 7
C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
[e-mail]
Help: Occasionally interference from receiver sockets plugged into adjacent wall
sockets or used with transformers (low voltage products) can affect the operating
Try placing one of the receiver sockets in another wall socket. For low voltage
products, place the transformer as far away form the receiver socket as possible.
RF Range
HE-106 Remote Control
Door Release
V1.0
The HE-106 Remote control Door Release allows
to you unlock and allow access control to a
variety of aluminium, timber and steel doors.
Simply press the button to unlock your door
Compatible with HE100, HE,101, HE301
-HE300, H301, HE303, HE307 & HE308
Suitable for right, left, inward and
outward opening doors.
-Fail Lock Operation
-30 Metre Range
-Automatic Relock
Contact:   Helpline: 0845 2301 231
The radio signals operating distance is reduced when the signal has to
pass through walls.The radio signal achieve a range of 30m inside a
building; this can be reduced depending on the type of material
HOME
easy
Set-Up Diagram:
The group setting allows you to switch "On/Off"
multiple receiver sockets/modules in one simple press.
To set a receiver to the group setting, set the receiver
into the learn mode as normal (see instructions Learn
Mode) and press group(G) On.
The socket will now switch On/Off with the group buttons; this stays the same
even if the group slide switch is on I, II, III or IV.
The receiver sockets/modules can still be used individually using the normal
On/Off buttons.
SX37
HE-106
ON
SX37
12V DC Power T
12V AC~300mA (Not Included)
Installation:
HE106 Door Release:
First select a suitable location for the HE-106 door release unit, it's recommended
that HE-106 is not placed in direct sources of sunlight, heat and onto metallic
surfaces, as this will the effect the operating performance.
Before fitting the door release unit, test the unit to make sure the location is suitable
e.g. operating the unit through an external wall will reduce the operating range, if
required move the unit close to the external wall.The HE-106 is an accessory product
The HE-106 is an accessory product for the HomeEasy
range of products, additional units are required for the
unit to operate.
1:The HE-106 base plate, can be attached using either the self adhesive strip or screws.
1:The HE-106 can be attached using either the self adhesive strip or screws (included)
2: Clip the HE-106 on
the base plate using
the key-hole slots.
3: Connect the power adapter into the terminal
connection "1" and "2" as per the diagram.
Terminal 1 + wire
Terminal 2 - wire Posative Negative
4: Plug the SX37 power adapter into a standard 13amp
socket, the HE-106 will beep twice and the LED will flash to
indicate that the power is connected. Now program a
HomeEasy remote control to the HE-106 unit (Remote
Control Not Included).
-See Pairing/Deleting Remote Control
5: Install the HomeEasy Door Lock into the door frame, making sure the location
and orientation is correct for the door.The HomeEasy Door lock is powered by a
12VAC -300mA transformer, connect one terminal from the transformer to one of
the terminals on the door lock.
T
12V AC~300mA (Not Included)
Door
Lock

6: Connect the second wire from the transformer
to terminal 4 on the HE106 and the connect a
wire from terminal 5 to the second terminal on
the HomeEasy Door Lock.
Then set dip-switch 3 to the "On" position.
1 65432
12 3 4 5 6 7
HomeEasy
Door Lock
Transformer
Product Specification:
Remote Control: HE-106
Input: 12V DC 800mA
Range: 30 Metres (Open Distance)
Frequency: 433.92MHz
Indoor Use Only
Warning: Never Exceed the Product
HE-Dooor Lock:
Input: 12Vac~ 300mA
Indoor Use Only
C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
suppor[email protected]
Contact:   Helpline: 0845 2301 231
1 65432
easy
HOME
II IIII IV
On
Up to Six remote control units can be paired with the HE-106 unit.
To program a HomeEasy Remote Control with the HE-106, set dip-switch 1 to the
"On" position and then press the "On" button on the HomeEasy remote control
(Except HE200 Remote Control).
Deleting Remote Control:
To delete a remote control that has been paired with a HE-106, set dip-switch 1 into
the "On" position and then press the "Off" on the paired remote control.The HE-106
will bleep twice to indicate that the remote control bas been deleted from the
memory of the HE-106, set dip-switch 1 back to the "Off" position.
HE-106 Memory Reset:
To delete all the remote control units paired with a HE-106, set all the dip-switches
into the "On" position, remove the SX37 from the socket and wait for 10 seconds.
The LED light will stay on and the unit will bleep twice, now set all the dip-switch to
the "Off" position, the led will now flash once every 3 second and make a long
continuous bleep, the HE-106 has now been reset.
Pairing/Deleting with Remote Control:
The HE-106 will bleep twice to indicate that the remote control is paired to the
HE-106, set dip-switch 1 back to the "Off" position, the HE-106 can be tested by
pressing the "On" button on the remote control.
1 65432
ON Example Remote control
Oparation:
Open Door:
Lock Door:
Test: 
1 65432
ON
Press the "On button on a paired HomeEasy Remote Control, for the
HE-100 press and hold the lock key.
Press the "Off" button on a paired HomeEasy Remote Control, if no lock 
command is received by the HE-106 it will automatically lock after
30 seconds. For the HE-100 release the lock key.
The HE-106 can be set into a test mode by setting dip-switch 2 to the
"On" position. 
The HE-106 will make 3 short bleeps when a "On/Off" command is
received, while in the test mode the door lock will not operate.
To exit the test mode set dip-switch 2 to the "Off" position.

6: Connect the second wire from the transformer
to terminal 4 on the HE106 and the connect a
wire from terminal 5 to the second terminal on
the HomeEasy Door Lock.
Then set dip-switch 3 to the "On" position.
1 65432
12 3 4 5 6 7
HomeEasy
Door Lock
Transformer
Product Specification:
Remote Control: HE-106
Input: 12V DC 800mA
Range: 30 Metres (Open Distance)
Frequency: 433.92MHz
Indoor Use Only
Warning: Never Exceed the Product
HE-Dooor Lock:
Input: 12Vac~ 300mA
Indoor Use Only
C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
suppor[email protected]
Contact:   Helpline: 0845 2301 231
1 65432
easy
HOME
II IIII IV
On
Up to Six remote control units can be paired with the HE-106 unit.
To program a HomeEasy Remote Control with the HE-106, set dip-switch 1 to the
"On" position and then press the "On" button on the HomeEasy remote control
(Except HE200 Remote Control).
Deleting Remote Control:
To delete a remote control that has been paired with a HE-106, set dip-switch 1 into
the "On" position and then press the "Off" on the paired remote control.The HE-106
will bleep twice to indicate that the remote control bas been deleted from the
memory of the HE-106, set dip-switch 1 back to the "Off" position.
HE-106 Memory Reset:
To delete all the remote control units paired with a HE-106, set all the dip-switches
into the "On" position, remove the SX37 from the socket and wait for 10 seconds.
The LED light will stay on and the unit will bleep twice, now set all the dip-switch to
the "Off" position, the led will now flash once every 3 second and make a long
continuous bleep, the HE-106 has now been reset.
Pairing/Deleting with Remote Control:
The HE-106 will bleep twice to indicate that the remote control is paired to the
HE-106, set dip-switch 1 back to the "Off" position, the HE-106 can be tested by
pressing the "On" button on the remote control.
1 65432
ON Example Remote control
Oparation:
Open Door:
Lock Door:
Test: 
1 65432
ON
Press the "On button on a paired HomeEasy Remote Control, for the
HE-100 press and hold the lock key.
Press the "Off" button on a paired HomeEasy Remote Control, if no lock 
command is received by the HE-106 it will automatically lock after
30 seconds. For the HE-100 release the lock key.
The HE-106 can be set into a test mode by setting dip-switch 2 to the
"On" position. 
The HE-106 will make 3 short bleeps when a "On/Off" command is
received, while in the test mode the door lock will not operate.
To exit the test mode set dip-switch 2 to the "Off" position.