© ELAN Home Systems 2010 • All rights reserved. Page 2
Figure 3
After charging the remote fully, proceed with the setup by following these steps:
1) Remove endcap and slide the power switch right to the "off" position.
2) Plug in the provided mini-USB cable to the remote USB port located on the left side behind the endcap (see figure one for location).
3) Plug the other end of the USB cable into a computer with g! Connect Pro already installed and running.
4) Slide the power switch left to the "on" position.
5) Enter the password requested on the HR2 screen using the following numeric buttons in this sequence: 3526 enter.
6) You are now ready to proceed with configuration using g! Connect Pro. Please refer to the HR2 integration note for more details.
Remote Configuring
Mini-USB
USB
© ELAN Home Systems 2010 • All rights reserved. Page 2
P/N 9901111 REV C
Limited Warranty
ELAN HOME SYSTEMS L.L.C. ( ELAN ) warrants the 2 to be free from defects in materials and workmanship for the period
of two years (2 years) from the date of purchase. If within the applicable warranty period above purchaser discovers that such
item was not as warranted above and promptly notifies ELAN in writing, ELAN shall repair or replace the item at the company’s
option. This warranty shall not apply (a) to equipment not manufactured by ELAN, (b) to equipment which shall have been
installed by other than an ELAN authorized installer, (c) to installed equipment which is not installed to ELAN’s specifications,
(d) to equipment which shall have been repaired or altered by others than ELAN, (e) to equipment which shall have been
subjected to negligence, accident, or damage by circumstances beyond ELAN’s control, including, but not limited to, lightning,
flood, electrical surge, tornado, earthquake, or other catastrophic events beyond ELAN’s control, or to improper operation,
maintenance or storage, or to other than normal use of service. With respect to equipment sold by, but not manufactured by
ELAN, the warranty obligations of ELAN shall in all respects conform to the warranty actually extended to ELAN by its supplier.
The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which
may be incurred in connection with repair or replacement.
Except as may be expressly provided and authorized in writing by ELAN, ELAN shall not be subject to any other obligations or
liabilities whatsoever with respect to equipment manufactured by ELAN or services rendered by ELAN.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES
EXCEPT WARRANTIES OF TITLE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
ATTENTION: TO OUR VALUED CUSTOMERS
To ensure that customers obtain quality pre-sale and after-sale support and service, ELAN Home Systems products
are sold exclusively through authorized dealers. ELAN products are not sold online. The warranties on ELAN
products are NOT VALID if the products have been purchased from an unauthorized dealer or an online E-tailer. To
determine if your ELAN reseller is authorized, please call ELAN Home Systems at (859) 269-7760.
" " HR
Removal and Replacement of the battery
Figure 4
Remove Screws
Pull Endcap out while pressing
Endcap Release Button
Endcap
Endcap Release Button
1
2
Remove Battery Retaining Bracket
and slide out old battery
Correct Battery orientation Incorrect Battery orientation
1) To access the battery locate the Endcap Release Button on the bottom of the remote. While depressing the Endcap release
button pull the Endcap away from the body of the remote as illustrated.
2) Remove the two screws holding the Battery Retaining Bracket in place using a #1 Phillips Screwdriver. Slide out the old battery.
3) CAUTION. Danger of explosion if battery is incorrectly replaced. Replace battery with only Elan approved battery
part number 2900008. (Contact your local dealer for replacement battery.)
4) Assure proper orientation while inserting replacement battery. Battery label should be faced down and gold plated charging
contacts should enter the unit first. Refer to the illustration above. Improper installation of the battery will result in
permanent damage to the remote.
Gold plated contacts
