HOME MERIDIAN Creations baby 6055-522 User manual

MODEL NUMBER
APRIL
6055-522
6056-522
Your little one will sleep secure in this Creations Crib. Proper assembly will ensure every
effort has been made to design this crib with you baby’s safely in mind. It is certified to
meet all safety guidelines from the JPMA-Juvenile Products Manufactures Association and
the CCPSC-Consumer Product Safety Commission.
Thank you for purchasing a Creations Crib. If you find that you are missing a part or if a part
Or if a part is defective in any way, contact your Creations retailer for assistance.

READ THIS PAGE BEFORE CRIB ASSEMBLY
Model Number: 6055-522 6056-522 Page 2
FOR CRIB: WARNING: Failure to follow these warnings and assembly
instructions could result in serious injury or death.
-CAUTION :Any mattress in this crib must be at least 27 1/4 inches x51 5/8 inches with a thickness not to
exceed 6 inches.
-Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
-Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO
NOT use crib if any parts are missing or broken.
Contact your Creations Baby dealer for any replacement parts and instructional literature needed.
-DO NOT substitute parts. Use only bolts or parts supplied by manufacturer.
-DO NOT allow ends of screws or sharp edges to be exposed.
-When a child is able to climb out or reaches a height of 35 inches(90cm), the crib should no longer be used. The
child should be placed into a toddler bed or regular bed.
-DO NOT place crib near window where cords from blinds or drapes may strangle a child. Strings can cause
strangulation! DO NOT place items with a string. Such as hood string or pacifier cords, around a child’s neck. DO
NOT suspend strings over crib or attach strings to toys for any reason.
-After raising a drop side or drop gate, make sure latches are secure. DO NOT leave a child in crib with a side
lowered. Be sure side or gate is in a raised or locked position whenever child is in the crib.
-If refinishing a crib, use a non-toxic finish specified for children’s products.
-When a child is able to pull to standing position, set mattress to lowest position and remove bumper pads, large toys,
or other objects that could serve for climbing out.
-Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
-DO NOT use a water mattress with this crib.
-DO NOT allow a child to crawl or play underneath crib.
-Crib must fully assembled prior to use and all bolts tighter securely when joining assemblies.
-Use caution when a vaporizer is in use. Aim vapor steam away from crib &other wood furniture.
FOR TODDLER BRD : WARNING :Failure to follow these warnings and the
assembly instructions could result in serious injury or death from entrapment or
strangulation. DO NOT place bed near windows where cords from blinds or drapes may
strangle a child.
-The mattress intended for use on this bed must have a minimum dimension of 51 5/8 in. length x 27 1/4 in. width x 6
in. thickness.
-The guardrails provided “must be used “ with this bed to avoid an entrapment between bed and mattress.
-The minimum age for a child in a toddler bed should not be less than 15 months and the maximum weight of the
child should not be greater than 50 lbs.
KEEP INSTRUCTIONS FOR FUTURE USE

MODELMUMBER:6055-522 6056-522 Page3
Identifying the Parts
The crib illustrations in these instructions are generic in nature. The crib you have purchased may not look like the
ones illustrated; however, they all assemble in the same manner.

MODELMUMBER:6055-522 6056-522 Page4
Identifying the Hardware
Identify the hardware included in the hardware bag using the illustrations below.
14 Decorattive bolts
2-3/4”(1/4”*20thread)
4 Decorattive bolts
1-1/4”(1/4”*20thread)
4 Decorattive bolts
5/8”(1/4”*20thread)
1 Allen wrench

MODELMUMBER:6055-522 6056-522 Page 5
ASSEMBLING AND OPERATING YOUR CRIB
NOTE: Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
This crib conforms to JPMA-Juvenile Products Manufacturers Association and the CPSC-Consumer Product
Safety Commission. Please adhere to the following guidelines for assembly, operation and maintenance.
zPower tools are not recommended for assembling your furniture.
zGive yourself plenty of room to work.
zDue to the size of this bed, it must be assembled within the space it will occupy.
zThe assembly will require at least two people to complete.
zMake sure all fasteners are tight.
zAbove all, take your time and read the instructions carefully.
Step 1: Attach Left and Right Crib Ends to Crib Spring:
Select four (4) each 5/8” bolts .Apply bolts thru the 4 upright brackets of the
Spring. Using Allen wrench, tighten bolts into the inserts located on the inside of the End Frames. Attach
the spring to the upper inserts for new born baby where spring is in highest position.

MODELMUMBER:6055-522 6056-522 Page6
Step 2: Assemble Footboard then Assemble Crib.
zUse six(6) each 2-3/4”bolts to assemble footboard to left and right posts. Tighten snugly with Allen wrench. To
attach the and spring assembly to the head and footboard, use eight(8) each 2-3/4” bolts thru the holes in the end
uprights and tighten snugly into the inserts.

MODELMUMBER:6055-522 6056-522 Page7
zTo CONVERT to Day bed with spring in lowest position:
Remove front frame from front posts. Keep base mounding in same position. Attach Guard Rail with four(4)
each 1-1/4”hex head bolts. Select guard rail for left or right position(your decision). Once Guard Rail is attached
to Youth Rail bolt this assembly to the inserts on the bottom of the front posts with four (4)each 2-3/4” bolts .
Notes: The front two brackets of the spring may need to be dropped down in a temporary out of way position by
removing the spring bolts. Reconnect the spring once the Youth/Guard Tail is in position.

MODELMUMBER:6055-522 6056-522 Page8
INSTRUCTION FOR CONVERSION TO FULL SIZE(4/6)BED
Make certain that all of the Footboard parts are fully assembled. There are two positions for the bed rails: an
upper position and lower position . We recommend starting at the lower position . Use eight(8)2-3/4” bolts to connect
the bed rails to the head and footboard. Once the bed rails are connected , lay nine(9)slats into the notched cleats as
noted below. Run 2 screws into each of the 2 end slats and middle slats. The bed is now ready for a mattress and for
use.

MODEL MUMBER: 6055-522 6056-522 Page9
CLEANING:
Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean
clothe lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry a;;
surface thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL,
OR COARSE RAGS SHOULD BE USE TO CLEAN THIS FINE FURNITURE. Never leave glasses with
water, ice or any liquid in contact with the wood surfaces as this can damage the wood components.
PERIODIC MAINTAINANCE:
1. Periodically check to make certain all bolts are fastened securely.
2. Check frequently that crib spring brackets are attached to the crib posts.
3. If you are missing a part or need a replacement part , do not use substitute parts. Ask you dealer for
replacement parts or contact Customer Service at [phone].
4. The spring adjustment bracket allow for the mattress to be lowered as your child grows. When your child
reaches a height of 35 inches, or can climb out of crib , you should place the child in a youth or regular
bed.
5. Save this instructions sheet in the event you disassemble the crib and need to reassemble it . This
instruction sheet will also be useful in identifying replacement parts if needed at a future date.
6. When storing your crib after disassembly, Place in a dry, moisture free environment, such as an attic or
basement . Keep away from water and vents from air conditioning and heaters, If possible, wrap with
blankets to prevent any damage to the wood frames, Make sure all hardware and instruction sheets are
kept with the crib while in storage.