Home Nordic Overbed Fitment User manual

Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
1447954
Nordic - Overbed fitment
03456 400 800
- 02-06-2014
Dimensions
idth : 248,9 cm
Depth : 49,0 cm
Height : 191,3 cm
344670050

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
• Check you have all the
components and tools listed on
pages 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• ake sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly .
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
Care and maintenance
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2

Drawer side, right/left x12
S120654
450x98x12 mm
Drawer front x6
V155811
395x15 x15 mm
Drawer back x6
S120650
351x98x12 mm
Drawer bottom x6
NM415861
361x44 x3 mm
Back x2
NM415853050F
1 41x39 x3 mm
Top/bottom x2
V155862
1633x4 0x15 mm
Top x6
V155863
383x4 0x15 mm
Top rail
V155804
1644x80x15 mm
Top rail x2
V155805
394xx15 mm
Door, Left x2
V155825
381x409x15 mm
Door, right x2
V1558 1
381x409x15 mm
Side left/right x2
V155845
399x4 5x15 mm
Plinth, front x2
V155802
395x96x15 mm
Divider x1
V155831
369x4 0x15 mm
Shelf x4
V155815
383x460x15 mm
Back
NM415855
164 x39 x3 mm
plinth, back x2
P155865
383x60x15 mm
Door left/right x2
V155826
893x395x15 mm
Side Right
V155840
1833x4 5x15 mm
Side Left
V155844
1833x4 5x15 mm
Left divider
V15586
1833x4 5x15 mm
Right divider
V155868
1833x4 5x15 mm
Please check you have all the panels listed below
Components - Panels
3
If you have damaged or missing components, call
the Argos Customer Helpline: 03456 400 800
123 4
5
6
7
8
10
11
12
13
9
14
15
16
23
17
22
20
21
1 8

BA10240
ø6,1x11,5 mm screw x16
BA10801
20x20x2 angle x8
BA101 0
ø4,0x35 mm screw x36
BA10833
15x15x10 mm x12
BA10468
ø40x30 mm Wooden knob x12
BA10400
ø6x30 mm wooden dowel x24
BA10590
ø15x9,5 mm cam x 0
BA10603
ø5/11x34 mm bolt x 0
BA10390
ø8x30 mm wooden dowel x36
BA102 0
ø5,8x8 mm screw x36
BA10050
ø3,5x15 mm screw x 2
BA10815
50x50x2 mm angle x8
BA10025
ø1,2x20 mm nail x150
BA10191
M4x9 mm screw x12
BA10508
ø26 cup hinge x12
BA10532
0 mm/3 mm crossplate x12
BA182002
wallstrap and instruction x2
Ba10688
500x250x Nail holder x1
B14359
1 x246 mm Drawer runner x12
BA10 96
80x15x2 mm connection plate x4
BA10830
5/5 mm shelf support x24
BA10233
ø4,9/M4x2 mm asambly screw x8
BA10215
M4x16 mm screw x8
Please check you have all the panels listed below
Components - Fittings
If you have damaged or missing components, call
the Argos Customer Helpline: 0845 640 30 30
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Tools required
Ruler - se this ruler to help correctly identify the screws
A B
R T L
J
i
D
NMC
K
4
PQF
G S H
VW
Y
Y d

Step 1
Assembly Instructions
Fix the drawer sides 11
to the drawer back 12 as
shown, using screws R.
Knock down the dowels
B into the holes indicated
on the drawer sides 11,
using a small hammer.
Step 2
Step 3
Slide the drawer bottom
13 into the drawer sides
11
Step 4
Screw the bolts D into
the holes indicated on
the drawer fronts 10.
5
R
R
R
B
B
B
B
D
D
11
11
11
11
11
11
12
13
10
x6
x6
x6
x6

Assembly Instructions
Push the drawer front 10
onto the the drawer
sides 11 as shown.
Push cams C into the
holes indicated. Arrow
pointing towards the
front.
Turn the cams C to the
right to fix the front 10.
Step 5
Step 6
Step 7
Important!
ake sure the
angle between
the drawer front
Fix the wooden knobs G
to the drawer front 10
using screws R.
6
10 and the drawer sides
11 is 90° before the
drawer bottom is fixed.
Fix the drawer bottom
13 to the drawer back
12 and the drawer front
10 using F.
To adjust the angle
between the drawer
sides and the drawer
front ush the fitting F
sidewards. See details.
!
C
C
F
F
G
R
11
11
11
11
10
10
10
13
12
x6
x6
x6

Assembly Instructions
Knock down the dowels
A into the holes
indicated on the back
plinths 6 and the
top/bottom 5 using a
small hammer.
Step 8
Step 9
Fix the crossplates P to
the sides 1 and 4 using
the premounted screws.
See details.
Position the cross late
exactly as shown.
See details.
Fix the angles V to the
sides 1, and 4 and the
divider 2 and 3 using
screws E. Place the
angles as shown.
See details.
7
Screw the bolts D into
the holes indicated on
the sides 1 and 4 and
the divider 2 and 3
A
A
A
A
A
A
6
5
x6
x2
1
1
2
3
4
4
P
P
P
P
P
P
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
VV
VV
V
V
VV
V
VV
V

Assembly Instructions
Slide the top of the
drawer runners S
backwards.
Fix the front end of the
drawer runners S to the
sides 1 and 4 and the
divider 2 and 3 using
screws K into the holes
indicated.
See details.
Step 10
Step 11
Slide the top of the
drawer runners S
forwards.
Fix the backend of the
drawer runners S to the
sides 1 and 4 and the
divider 2 and 3 using
screws K into the holes
indicated.
See details.
8
1
2
3
4
S
S
S
S
S
S
S
S
S
S
S
S
S
S
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
KK
KK
K
K
K
K
K
K
K
3
1
2
4
S
S
S
S
S
S
S
S
S
S
S
S
S
S
K
K
K
K
K
K
K
K
K
K
K
K
K
K

Assembly Instructions
Place the sides 1 and 4
and the divider 2 and 3
onto the bottoms 5 and
the back plinths 6.
Push the cams C into the
holes indicated. Arrow
pointing towards sides.
Turn the cams C to the
right to fix the sides 1
and 4 and the divider 2
and 3.
Step 12
9
1
2
3
4
5
55
5
5
5
6
6
C
C
CC
C
C
C
CC
C
C
C
C
C
C
C
C
C
CC
C
C

Assembly Instructions
Place the back 16 into
the rebates in the
sides/divider 1, 2, 3 and
4.
Step 13
10
!
Im portant!
Make sure the
angle between
the to and the
sides is 90° when
the back is
attached.
Fix the backs to the
sides/ divider 1, 2, 3
and 4 and the to 5 and
the back linth 5 using
nails i.
Use Nail holder Yd and a
small hammer.
Place the front linths 7
as shown.
Fix the front linths 7 to
the sides/divider 1, 2, 3
and 4 using screws E
into the angles V.
1
2
3
4
6
6
7
7
16
16
ii
i
i
i
i
i
i
i
i
i
i
V
V
V
V
V
V

Assembly Instructions
Place the top rail 8 onto
the top 5.
Fix the top rail to the top
using angles W and
screws T.
Step 14
Step 15
11
Fix the cross lates P to
the divider 21 on both
sides and to the sides
20, using the
re-mounted screws.
Poistion exactly as
shown.
See details.
Screw the bolts D into
the holes indicated on
the sides 20 and the
to /bottom 23.
Knock down the dowels
A into the holes
indicated on the
to /bottom 23 using a
small hammer.
x4
5
5
5
8
8
8
T
T
T
T
T
TT
T
T
T
T
T
T
T
TT
T
T
T
T
YY
Y
Y
Y
21 21
20
23
P
PP
P
P
P
x2
x2
P
D
D
D
D
D
D
D
D
D
A
A
A
A

Assembly Instructions
Place the top/bottom 23
onto the divider 21 as
shown. Note the
chamfered edges.
Push cams C into the
holes indicated. Arrows
pointing towards the
top/bottom 23.
Turn the cams C to the
right to fix the
to /bottoms 23
Step 16
Step 17
Place the sides 20 onto
the top/bottom 23. Not
the rebates.
Push cams C into the
holes indicated. Arrows
ointing towards the
sides.
Turn the cams C to the
right to fix the sides.
12
23
23
23
23
21
20
20
C
C
C
C
C
C
C
C
C
C
C
C

Assembly Instructions
Place the back 17 into
the rebates in the sides
20 and onto the
top/bottom 23.
Step 18
Step 19
Fix the connecting plates
Y onto the to 23 using
screws T.
Place the connecting
late exactly as shown.
See details.
13
!
Important!
ake sure the
angle between
the top and the
sides is 90° when
the back is
attached.
Fix the back 17 to the
sides 20 and the
top/bottom 23 using
nails i.
Use the nailholder Yd
and a small hammer.
Place the to rail 22
onto the to 23.
Fix the to rail 22 onto
the to 23.
Fix the to rail 22 to the
to 23 using angles W
and screws T.
17
TT
T
T
TT
T
T
TT
T
T
T
T
T
T
TT
T
T
W
W
W
W
W
i
i
i
i
i
i
i
22
22
20
20
23
23
T
T
TT
TT
TT
YY
Y
Y
Y
Y
Y
side
3,0 cm
back
3,5 cm
T
T

Assembly Instructions
Place the 4 door
wardrobe as shown.
Fix it using screws N
and assembly screws
into the holes indicated.
See details
Fix the connecting late
Y to the to 5 using
screws T.
Step 20
Step 21
it is recommended that
the wardrobe is fixed to
the wall.
Use the fittings J. Follow
the instruction included
with the fitings.
Knock the shelf supports
L into the holes of the
sides 1, 2, 3 and 4.
Place the shelves 9.
14
!
Warning !
The wardrobe is
heavy. Lift with
care.
M
M
M
M
M
M
MM
M
N
N
N
N
N
TT
T T
Y
TT
Wallstrap and instruction
x2
LL
L
L
L
LL
L
L
L
L
12
3
4
9
9
9
9
x3
x3 x3
x3 x3
x3
x3 x3

Assembly Instructions
Place the cup hinges Q
into the holes indicated
on the doors 14, 15 and
18.
Fix the hinges using
screws T.
Step 22
Step 23
Pull our the drawer
runners. Slide the drawer
onto the runners.
Fit and fix the lower
drawer first and work
your way up.
Dix drawer to the drawer
runners using screws H.
15
Q
Q
Q
Q
Q
Q
Q
15
14
1 8
TT
TT
T
T
TTT
T
TT
TT
x2
H
H
H
x2
x2

Assembly Instructions
Slide the cup hinges Q
onto the crossplates P.
Fix the hinges using the
pre-mounted screws in
the crossplates.
See details.
Fix the wooden knobs G
to the doors 14, 15, 18
using screws R.
Step 24
16

Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline:
03456 400 800
Home Retail Group - 489-499 Avebury Boulevard - Saxon Gate West - Central ilton Keynes K9 2NW
Adjusting the doors
left/right.
a:
To adjust the door
towards the left hand
side - turn the adjusting
screw to the right.
b:
To adjust the door
towards the right hand
side - turn the adjusting
screw to the left.
Adjusting the doors
for ards/back ards.
a:
Loosen the fixing screw.
b:
Push the cup hinge/the
door forwards or
backwards to adjust.
c:
Tighten the fixing screws
of ALL the crossplates.
Adjusting the doors
up/do n.
a:
Loosen the two
pre-mounted screws of
each crossplates, UT
ONLY as much as it will
allows the crossplates to
move up and down.
b:
Push the door up or down
to adjust.
c:
Tighten the pre-mounted
screws of ALL
crossplates.
Assembly is complete.
Step 25
17

Wall Mounting & Fixings
18
Important:
When drilling into walls always check that there
are no hidden wires or pipes ect. Make sure
that the screws and wall plugs being used are
suitable for supporting your unit.
Consult a qualified tradesperson if you are
unsure.
HINTS
1) General Rule Always use a larger screw and a wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is
fitting below the ceramic tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
!
!
!
a Guide to
Types of walls
You can use one of the following
types of wall plug if your walls are
made of brick, breeze block,
concrete, stone, wood or plaster
board.
No. 1 "Standard" Wall Plug
General Wall Materials.
These come in various sizes and are
made from plastic or sometimes
wood fiber.
No. 2 "General Purpose" Wall
Plug Aerated/Breeze Block.
General aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case.
For light loads, a General Purpose
Plug can be used.
No. 3 "S ield Anc or" Wall Plug
Heavy loads.
For use with heavier loads such as
T & HiFi Speakers and Satelite
Dishes etc.
No. 4 "Gavity Fixing" Wall Plug.
For use with plaster board partitions
or hollow wooden doors.
No. 5 "Gavity Fixing Heavy
Duty" Wall Plug.
For use when fitting or surpporting
heavy loads such as shelving, wall
cabinets, coat racks.
No. 6 "Hammer Fixing" Wall
plug.
For use with walls stuck with plaster
board. The hammer fixing allows it
to be fixed to the wall rather than
the plaster board. Always check the
fixing is secure to the retaining wall.
Care & Maintenance
SAFETY
Always check the fitting and location
to ensure your safety in and around
the home.
Care & Maintenance
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.