Home Scandinavia - Chest of drawers User manual

Scandinavia - Chest of drawers
Dimensions
Width - 78cm
Depth - 40cm
Height - 71cm
Issue 3 - 23/11/2016
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Assembly Instructions
476/8654
487/7174
Retain these instructions for future reference
Sainsbury’s Argos
489-499 Avebury Boulevard
Saxon Gate West
Central Milton Keynes
MK9 2NW

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Tools required
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
• Check you have all the
components and tools listed on
pages 2 and 3.
• Do not use this item if any
components are missing or
damaged.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Assembly to be carried out by
a competent adult only
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Folding and unfolding this
product should only be carried
out under adult supervision.
• Ensure that ngers and legs
are clear of all adjustments
when adjusting this product.
• Regularly check all fastenings
to ensure that they properly
tightened.

2
Components - Panels
Please check you have all the panels listed below
Front left leg
67x 3.2cm)
2
Front right leg
(67 x 3.2cm)
5
Left side panel
(62.6 x 30cm)
1
Back x 2
(60x34.4 cm)
10
Small drawer back x 2
(28 x 11cm)
13
Large drawer back x 3
(62 x 11cm)
16
Large drawer front x 3
(66.6 x 14cm)
15
Small drawer front x 2
(32.4 x 14cm)
11
Large drawer bottom x 3
(64 x 33cm)
17
Small drawer bottom x 2
(30 x 33cm)
14
Plinth x 2 (67 x 4.4cm)
9
Divider (36.6 x 14.5cm)
8
Top (78 x 40cm)
7
Right side panel
(62.6 x 30cm)
4
Drawer side x 10
(34 x 10cm)
12
Back left leg
(67 x 3.2cm)
3
Back right leg
(67 x 3.2cm)
6
If you have damaged or missing components,
call the Customer Helpline: 03456 400 800

3
Please check you have all the ttings listed below
Cam 12 mm x 30
Cam 15 mm x 8
Screw 14 mm x 1
Knob x 8
Wall plug x 1
Screw 35 mm x 28
Screw 20 mm x 1
Washer x 2
Nail x 30
Wall strap x 1
Screw x 40
Drawer runners x 5
Locking pin 34 mm x 8 Dowel 40 mm x 12
Locking pin 24 mm x 30 Dowel 30 mm x 4
Ruler - Use this ruler to help correctly identify the screws
A
D
G
J
M
P
H
K
N
I
L
O
P 1 P 2 P 3 P 4
E F
B C
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
100 20 30 40 50 60 70 80 90 100
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings

4
Components - Key Diagram
Function of Cam and Locking Pin
9
10
17
16
x3 x2
15 1112
12
12
12
13
14
8
7
10
9
2
5
1
4
3
6
Left side Right side

5
Assembly Instructions
Step 1
Step 2
Inserting the dowels
and mounting the
locking pins to the
legs.
Insert the dowels F
into the holes indicated
on the legs 2and 3.
Screw the locking pins
Einto the holes
indicated on the legs
2and 3.
Note: Insert locking pins
E as far as shown. Do
not over tighten.
Mounting legs to the side
panels.
Fit the legs 2and 3.
onto the side panel 1.
Note: See page 5
“Function of cam and
locking pin“.
Place the cams Dinto the
holes indicated on the side
panel 1.
To tighten cams: Turn to
the right using a
screwdriver.
2
2
2
3
1
1
3
D
D
D
D
D
F
F
F
F
F
F
F
E
E
E
E
E
Rebate=Back

6
Step 3
Inserting the dowels
and mounting the
locking pins to the
assembled side.
Insert the dowels Cinto
the holes indicated
Screw the locking pins
Binto the holes
indicated on the legs
2and 3.
Note: Insert locking pins
Bas far as shown. Do
not over tighten.
2
2
3
3
1
1
2
O
O
O
O
O
O
O
O
C
CB
B
B
C
Step 4
Attaching the drawer
runners to the
assembled side.
Fix the drawer runners
P 3 to the left side 1,
P 2 to the right side 4
using screws Othrough
the holes indicated
To tighten screws:
Turn to the right using a
screwdriver.
Repeate these steps
with right side.
Assembly Instructions
Left side
Left side
P 3
P 3
P 3
P 3

7
Step 6
Step 7
Adding the plinths to
the left side.
Fit the left side 1onto
the plinths 9.
Note: See page 5
“Function of cam and
locking pin“.
Place the cams Ainto
the holes indicated on the
plinths 9
To tighten cams: Turn to
the right using a
screwdriver.
Adding the plinths to
the right side.
Fit the right side 4onto
the plinths 9.
Note: See page 5
“Function of cam and
locking pin“.
Place the cams Ainto
the holes indicated on the
plinths 9.
To tighten cams: Turn to
the right using a
screwdriver.
Assembly Instructions
9
9
1
1
4
9
9
9
9
Left side
Right side
Left side
A
A
A
A
A
A
Rebate=Back
Rebate=Back

8
Step 8
Step 9
Step 10
Attaching drawer
runners to the divider.
Fix the drawer runner P 2
to the divider left side and
the drawer runner P 3 to
the divider right side with
screws O into the holes
indicated on the divider
8.
Mounting the locking
pins to the top.
Screw the locking pins B
into the holes indicated
on the top 7.
Note: Insert locking pins
Bas far as shown. Do
not over tighten.
Assembling the divider
to the top.
Fit the divider 8onto
the top 7.
Note: See page 5
“Function of cam and
locking pin“.
Place the cams Ainto
the holes indicated on
the divider 8.
To tighten cams: Turn to
the right using a
screwdriver.
Assembly Instructions
8
8
7
7
O
O
O
B
B
B
A
A
A
B
B
B
B
O
Front edge
P 2
P 3
Rebate=Back

9
Assembly Instructions
Step 11
Assembling the top to
the sides.
Attach the top 7onto
the sides 1and 4.
Note: See page 5
“Function of cam and
locking pin“.
Place the cams Ainto
the holes indicated on the
sides 1and 4.
To tighten cams: Turn to
the right using a
screwdriver.
7
7
A
A
AA
A
Rebate=Back
Right side Left side
14