HomeAware HA360VB2.1 User manual

The HomeAware Vibe is a new accessory that connects to
the HomeAware main unit, transmitters, and receivers. This
personal pager will alert you to events like the smoke/CO
detector, the baby crying, the phone ringing and many more.
The HomeAware Vibe will alert you with multiple colored
LED lights, vibration and an audio alert, all patterned to a
specific alert. Simply clip the HomeAware Vibe to your
waistband or slip it into a pocket and enjoy the freedom of
never missing an alert again. In fact the HA360VB1.2 can
also act as an emergency alert notification device in case you
have fallen or have another emergency you need help with.
By simply pushing the PAGE button on the front of the unit it
will send an alert notification to all your HomeAware
receivers and the main unit. Because it is portable and the
increased range due to the HomeAware’s mesh network, you
will be safe throughout your house and out.
HA360VB2.1 Features
 Emergency alert button when help is needed. Ultra-high
brightness strobe for maximum visibility.
 Clips easily on waistband and small enough to slip into a
pocket.
 Connects to the HomeAware main unit, transmitters, and
receivers.
 Alert patterns unique to you, vibrate, sound, flashing
lights, or different colors for different alerts.
Battery Features
Note: After you have received your HomeAware Vibe, please
fully charge before first use. A complete charge will take
approximately 3 hours.
 Green – charge complete
 1 Red light – battery low
 2 Red Lights – Battery half charged
If the Vibe is switched to Off the battery indicators lights will
not be lit but the Vibe is still charging.
Low Battery Check
The Vibe will alert you when the battery is getting low.
Depending on what switch or switches that are on, it will be
a single yellow blink, vibration or beep.
TO USE THE HOMEAWARE VIBE HA360VB2.1 AS A RECEIVER
OF THE HOMEAWARE SYSTEM
Linking:
 Press SET UP button on the main unit and the word LINK
will be shown on the display, press ENTER. LINK will begin
blinking.
 Press and hold down the PAGE button on the front of Vibe,
PICK DEVICE will be shown on display of the main unit.
Press the blue MINUTE/down arrow button until the
display reads HELP, then press ENTER. DONE will be
shown on the display when linking is completed.
Switch / Page Button Controls
There are several ways that the Vibe can be set to notify you of
alerts happening in or around your home. Pick one, two or all
four with a flip of a switch.
 V - Vibrate
 S - Sound
 F - Flash
 C – Color
 Door - Green
 Baby – Blue
 Phone – Orange
 Smoke/CO – Red
 Cyan – Universal
 Low Battery – Single Yellow blinking light
 Lost Link – Double Yellow blinking light
PAGE Button / Emergency Help
When the PAGE button on the front of the HomeAware Vibe is
held down for 3 seconds, it sends a HELP alert to the main unit.
HA360VB2.1 – Quick Start Guide

HA360VB2.1 – Quick Start Guide
FCC REQUIREMENTS
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions; (1) This device might
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide
responsible protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not interfere in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is
encouraged to try to correct the interference by one or more of
the following measures:
i. Reorient or relocate the receiving antenna.
ii. Increase the separation between the equipment and
receiver.
iii. Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
iv. Consult the dealer or and experienced radio /TV
technician for help
Modification not expressly approved by the manufacturer
could void the user’s authority to operate the equipment under
FCC rules.
CANADIAN CERTIFICATION
This device complies with Industry Canada license exempt RSS
standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference
that may cause undesired operation of the device.
GENERAL DATA
Power Consumption: DC5V, 400mA
The Lightening
flash and
arrowhead within
the triangle is a
warning sign
alerting you of
dangerous voltage
inside the
product.
CAUTION:
TO REDUCE THE
RISK OF ELECTRICAL
SHOCK, DO NOT
REMOVE THE
COVER (OR BACK)
FROM THE
PRODUCT. NO
USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING
TO YOUR SONIC
ALERT DEALER.
The exclamation
mark within the
triangle is a
warning sign
alerting you of
important
instructions
accompanying the
product.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS DEVICE TO RAIN OR MOISTURE.
The normal function of the product may be disturbed by
Strong Electro Magnetic Interference. If so, simply reset the
product to resume normal operation by following the
instruction manual. In case the function could not resume,
please use the product in other location.
– Attention should be drawn to the environmental
aspects of battery disposal.
– T This indicating separate collection for electrical
and electronic equipment.
SONIC ALERT’S 1 YEAR LIMITED WARRANTY
The HomeAware™ HA360VB2.1 is warranted against
manufacturing defects in materials and workmanship for
one (1) year from the date of purchase. Within this
period Sonic Alert will repair or replace at our option the
HomeAware™ HA360VB2.1 without charge for parts and
labor.
Simply contact our customer service department
to obtain an RA (return authorization number)
and instructions on how to process your product
for return. Call 248-577-5400 or e-mail to
[email protected]. You’ll need a
copy of your receipt to process the return
authorization.
Sonic Alert Warranty Center
850 Stephenson Hwy., Suite 323, Troy MI 48083
248-577-5400
Made in China
Sonic Alert, Troy, MI 48083
www.SonicAlert.com