homechoice Tweety Co User manual

1
Tweety Co Sleeper
assembly instruction
Shop online – go to
homechoice.co.za
Please follow these guidelines for safe assembly:
1) Because this item is large, we recommend that two people assemble it together,
in the room in which it will be used.
HomeChoice will not be held liable for damages caused by improper assembly.
2) Please make sure that you have all the parts and hardware items listed before you start
assembling your bed. If you nd that something is missing, please do not assemble.
Contact our Customer Service on 021 680 8000.

2
Please make sure that you have all the parts and hardware items listed before you start to assemble.
PARTS LIST:
Part
ACarry Bag 1 piece
BFrame 1 piece
CMattress 1 pieces
DBassinet 1 pieces
E
Bassinet Tubes
Tapered Ends
2 pieces
2 pieces
FAnchor Plates and Strap 1 pieces

3
Opening for Use
With the feet on the oor pull
the feet apart so that they
are approximately 60cm/24”
apart. Lift the short sides of
the cot upwards until they lock
into position.
Step 2
Unzip the travel bag and
remove the frame and
mattress. Place the cot in the
vertical position and open the
touch fasteners to remove the
mattress.
Step 1
Now lift the long sides of the
cot upwards until they lock
into position. Check that all
four sides have engaged
correctly by pressing down
on each arm at the centres.
If you have diculty locking
the sides, lift the centre of the
base a little higher and start
the process again.
Step 3

4
Opening for Use
Place the mattress in the
travel cot with the padded
side up. Align the touch
fasteners on the mattress
with those on the base
and press down to ensure
they are stuck together.
.
Step 5
Now push the centre of the
cot base downwards until it
audibly locks into place.
Step 4
Note - The travel cot is ready for use only when the locking mechanisms are engaged.
Check carefully that they are fully engaged before using the travel cot.
If you nd that something is missing, please do not assemble. Contact our Customer Service on 021 680 8000.

5
Folding
Lift the side rails slightly (a)
and hold the lock in
the middle of the rail (b)
(indicated with arrows).
Hold the lock pressed
whilst gently lowering the side
rail (c). Ensure that the side rail
disengages on
both sides of the mechanism.
Pull together the 2 supporting
legs underneath the fabric
to centre base as close as
possible (d).
Step 2
Lift the handle in the base
under the mattress and pull the
centre of the base upwards.
Step 1
(a) (b) (c) (d)

6
Folding
With the upper part of the travel
cot in the closed position, push all
4 feet together.
Step 4
Repeat this process with the
short sides. Check that all 4
sides have disengaged prop-
erly and then pull the center of
the base. If you have diculty
unlocking the sides, lift the
center of the base a little
higher and start the process
again.
Step 3
a) Wrap the mattress around
the travel cot tightly with
the padded section inside.
Fasten the touch
fasteners through the tabs
and secure. Pull the travel
bag over the travel cot
and close the bag with the
zip. (Shown in g. a).
b) You can pack all the
additional parts inside -see
g. b
Step 5
Bassinet Tubes
Bassinet Tubes (x2)
- Tappered Ends (x2)
g a
If you nd that something is missing, please do not assemble. Contact our Customer Service on 021 680 8000.

7
Bassinet Assembly Instruction
Drape bassinet over the end
of the cot. Fasten the plastic
clips on the top rail. There are
2 plastic clips on each longer
rail and 2 on each short rail.
Figure 2.
IMPORTANT: The plastic clips
on the rail can be adjusted
accordingly.
Step 2
Remove the mattress pad
from the bottom of the
playard to use inside your
bassinet.
Release VELCRO®straps that
hold down the mattress pad
and remove from playard.
Step 1
Take out 4 bassinet support
tubes contained in the plastic
bag. Insert the bassinet tubes
into the 4 bassinet sleeves.
Ensure that one tapered tube
is placed on each side and the
tapered ends point inwards.
Connect the support tubes
together.
Place the mattress onto the
bassinet.
Step 3

8
Convert into the co-sleeping position from the
freestanding bassinet
Undo the zipper located on
each short side, Tuck the fabric
under the mattress and then
nd the plastic hooks under-
neath the bassinet. Once locat-
ed, clip them onto the top bar
and ensure that they are rmly
clipped.
Place the mattress onto the
bassinet.
Warning: If a gap is visible on
either side of the mattress after
installing, reposition the
mattress or bassinet then
stretch the mattress and sheet
on both ends to cover the gaps.
Step 2
Remove the velcro®from the
inside of the lowering rail as
picture.
Find the locking buckle under
the plastic corners on the left
and right sides, latch them
outward to unlock and then
slide down the top bar until it
reaches to the bottom limit.
Note: The left and right side
plastic corner pieces must be
slid down at the same time, so
that the top
Step 1
4 PLASTIC HOOKS FOR CO-SLEEPING MODE
Cierre
If you nd that something is missing, please do not assemble. Contact our Customer Service on 021 680 8000.

9
How to attach the co-sleeper bedside bassinet to
adult bed
The top edge of the LOWERING RAIL when used in the co-sleeping position must be level
with, or below, the top of adult mattress.
Slide the anchor plate and straps under the mattress, placing the anchor plate ush
against the mattress on the opposite side from this product.
Connect both straps to each short side of the bassinet by passing the buckle through the
“belt loop” at the front leg of the product and then connect the buckle to the rear leg.
Make both straps as tight as possible against the parental bed. It must be tight enough
to make a slight indentation in mattress. To test if the product is tightly secured to adult
bed, push it with your hands to make sure the gap is no more than ½”(13mm). If more than
½”(13mm), re-adjust strap to pull tighter. When the bassinet is tight and ready to use, roll
the excess strap up and secure. Always tighten straps before each use.
It is recommended to make the strap shorter than the width of the mattress to ensure the
co-sleeper is pressed securely against the parental bed without any gaps.
Unacceptable bed,
mattress, boxspring and frame not in-line
Frame extended
Acceptable bed frame in-line
Mattress, boxsprings and
frame aligned

10
If you nd that something is missing, please do not assemble. Contact our Customer Service on 021 680 8000.
Important-Please read these instructions fully before
starting assembly
WARNING Be aware of the risk of open re and other sources of
heat, such as electric bar res, gas res etc in the near vicinity
of the cot.
WARNING Do not use the cot if any part is broken, torn or missing and use
only spare parts approved by the manufacturer.
WARNING Do not leave anything in the cot, such as toys, or place the cot
close to another product which could provide a foothold or
present a danger of suocation or strangulation, e.g. strings,
blind/curtain cords etc.
WARNING Do not use more than one mattress in the cot.
WARNING Do not use your travel cot without the mattress.
WARNING The depth of the mattress should not reduce the side height
above it to less than 500mm
WARNING Keep your travel cot away from electric cords or wires.
WARNING Failure to extend the top rails and lock them securely creates a
safety risk. ALWAYS check that the rails are fully engaged,
locked and strapped before use.
WARNING If the child can stand unaided or is able to climb out of the cot,
the cot cannot continue to be used for that child.
WARNING Do not use any other mattress which has not approved by the
manufacturer.
WARNING Do not allow young children to play unsupervised in the
vicinity of, or in the travel cot.
WARNING Do not use the bassinet when the child can sit or kneel or
pull him/herself up.
WARNING Never leave your child unattended on the changing station.
Safety and Care Advice

11
If you nd that something is missing, please do not assemble. Contact our Customer Service on 021 680 8000.

12