HOMEDEPOT Side By Side Dresser User manual

Materials and Tools
FORMALDEHYDE-FREE TECHNOLOGY
FEATURING
MATERIALS:
• 1-1/4" pocket hole screws
• 1-1/4" brad nails
• 4" furniture legs with mounting plates
• 8 sets of 18" drawer slides
• Cabinet pulls
• Edge banding (optional)
• Wood glue
• Sandpaper (100, 150, 220 grits)
• Finishing supplies (primer & paint,
or stain, sealer)
LUMBER:
• 5 – 4' x 4' x 3/4" PureBond plywood
project panels
• 1 – 4' x 4' x 1/4" PureBond plywood
project panel (Cherry was used in example)
TOOLS:
• Jigsaw, table saw, miter saw, or hand saw
• Pocket hole jig
• Drill
• Brad nailer
• Pencil, ruler, square, tape measure
• Sander
• Iron for edge banding
• Edge banding trimmer or craft knife
CUT LIST:
• 1 – 3/4" plywood at 19-1/2" x 42-1/2" – Bottom
• 2 – 3/4" plywood at 19-1/2" x 31" – Sides
• 1 – 3/4" plywood at 19-1/2" x 31" – Divider
• 2 – 3/4" plywood at 1-1/2" x 41" –
Upper Stretchers
• 6 – 3/4" plywood at 1-1/2" x 20-1/8" –
Front Stretchers
• 1 – 1/4" plywood at 31-3/4" x 41-3/4" – Back
• 1 – 3/4" plywood at 20-1/4" x 43-1/2" – Top
• 16 – 3/4" plywood at 5-1/2" x 19-1/8 –
Drawer Box Front & Back
• 16 – 3/4" plywood at 5-1/2" x 16-1/2" –
Drawer Box Sides
• 8 – 3/4" plywood at 16-1/2" x 17-5/8" –
Drawer Box Bottom
• 8 – 3/4" plywood at 6-3/4" x 19-7/8" –
Drawer Fronts
Side By Side Dresser
Free Plans to Build a Side By Side Dresser

Side By Side Dresser
STEP 2
STEP 1
Notes:
Edge banding will be applied to the
exposed edges of the plywood prior to
assembly.
Cut the piece for the bottom. Secure the
mounting plates to the bottom according
to the manufacturer's installation
instructions. Add the furniture feet.
Cut the pieces for the sides. With the
pocket hole jig set for ¾" material, drill
pocket holes in the lower edges of the
sides. Secure the sides, flush with the
end edges of the bottom, using glue and
1-1/4" pocket hole screws.
FORMALDEHYDE-FREE TECHNOLOGY
FEATURING

STEP 3
Cut the piece for the divider. Cut the
notches using a jigsaw or a bandsaw,
and drill pocket holes in the lower edge.
Secure the divider to the bottom using
glue and 1-1/4" pocket hole screws.
FORMALDEHYDE-FREE TECHNOLOGY
FEATURING
Side By Side Dresser
STEP 4
Cut the pieces for the upper stretchers
and drill pocket holes in each end.
Secure to the sides using glue and 1-1/4"
pocket hole screws.

STEP 5
Cut the pieces for the front stretchers.
Drill two pocket holes in one end and
one pocket hole in the other end o
center so it will not conflict with the
pocket hole screws on the opposite side
of the divider. Secure the stretchers to
the sides and dividers using glue and
1-1/4" pocket hole screws.
FORMALDEHYDE-FREE TECHNOLOGY
FEATURING
Side By Side Dresser
STEP 6
Cut the piece for the back. Secure
the back to the sides, bottom, upper
stretcher, and divider using glue and
1-1/4" brad nails.

STEP 7
Cut the piece for the top. The top will
be flush with the back and will overhang
the sides and front by ½". Secure the
top using glue and 1-1/4" brad nails.
FORMALDEHYDE-FREE TECHNOLOGY
FEATURING
Side By Side Dresser
STEP 8
Cut the pieces for the drawer boxes.
Drill pocket holes in all four edges of
the bottom as well as each end of the
sides. Assemble the drawer boxes as
shown using glue and 1-1/4" pocket
hole screws. Install the drawer slides
according to the manufacturer's
installation instructions, locating them
¾" back from the front edge of the
sides.

STEP 8
Cut the pieces for the drawer boxes.
Drill pocket holes in all four edges of
the bottom as well as each end of the
sides. Assemble the drawer boxes as
shown using glue and 1-1/4" pocket
hole screws. Install the drawer slides
according to the manufacturer's
installation instructions, locating them
¾" back from the front edge of the
sides.
STEP 9
Cut the pieces for the drawer fronts.
Mark the position for the drawer pulls
and drill the holes. Shim the drawer
front in the opening – there will be a
1/8" gap around all sides – then drive
screws through the holes for the drawer
pulls into the drawer box. Open the
drawer and secure the drawer front
using countersunk 1-1/4" screws from
the inside. Remove the screws from
the holes for the drawer pull then finish
drilling the holes. Install the drawer pull.
Finish as desired.
FORMALDEHYDE-FREE TECHNOLOGY
FEATURING
Side By Side Dresser