Homelite HG6000 User manual

SAVE THIS MANUAL FOR FUTURE REFERENCE
Your new generator has been engineered and manufactured to a high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
Thank you for your purchase.
DANGER: You WILL be KILLED or SERIOUSLY HURT if you do not follow the instructions in this operator’s
manual.
OPERATOR’S MANUAL
PORTABLE GENERATOR SET
6,000 WATT
HG6000
FUEL
AC CIRCUIT
BREAKER

Page 2
TABLE OF CONTENTS
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product, making it easy to maintain and operate.
FUEL
AC CIRCUIT
BREAKER
DANGER
GROUNDING THE GENERATOR
To avoid the risk of shock or electrocution, generator must be properly grounded. The nut and ground terminal on the
frame must always be used to connect the generator to a suitable ground source. The ground path should be made
with #8 size wire. Connect the terminal of the ground wire between the lock washer and the nut, and tighten the nut
fully. Connect the other end of the wire securely to a suitable ground source.
The National Electric Code contains several practical ways in which to establish a good ground source. If a steel or iron
rod is used, it should be at least 5/8 in. diameter, and if a nonferrous rod is used, it should be at least 1/2 in. diameter
and be listed as material for grounding. Drive the rod or pipe to a depth of 8 ft. If a rock bottom is encountered less than
4 ft. down, bury the rod or pipe in a trench.
All electrical tools and appliances operated from this generator
must be properly grounded by use of a third wire or be “Double
Insulated.”
It is recommended to:
1. Use electrical devices with 3-prong grounded plugs.
2. Use an extension cord with a 3-pole receptacle and a
3-prong plug at opposite ends to ensure continuity of the
ground protection from the generator to the appliance.
Check and adhere to all applicable federal, state, and local
regulations relating to grounding specifications. Consult a quali-
fied electrician or service personnel if the grounding instructions
are not completely understood or if in doubt as to whether the
generator is properly grounded.
 Introduction .................................................................................................................................................................... 2
 General Safety Rules ..................................................................................................................................................... 3
 Specific Safety Rules ..................................................................................................................................................... 4
 Symbols ......................................................................................................................................................................5-7
 Electrical .....................................................................................................................................................................8-9
 Features .................................................................................................................................................................10-11
 Loose Parts List ........................................................................................................................................................... 12
 Assembly ................................................................................................................................................................13-14
 Operation ................................................................................................................................................................14-16
 Maintenance ...........................................................................................................................................................17-20
 Troubleshooting ........................................................................................................................................................... 21
 Wiring Diagram ............................................................................................................................................................ 22
 Warranty ....................................................................................................................................................................... 23
 Parts Ordering / Service .................................................................................................................................Back Page

Page 3
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electrocution,
fire, and/or carbon monoxide poisoning, which will cause
death or serious injury.
 Do not allow children or untrained individuals to use this
unit.
� Never start or run the engine inside a closed or partially
enclosed area. Breathing exhaust fumes will kill you.
� Wear eye protection which is marked to comply with ANSI
Z87.1 as well as hearing protection when operating this
equipment.
� Keep all bystanders, children, and pets at least 10 feet
away.
� Wear sturdy and dry shoes or boots. Do not operate while
barefoot.
� Do not operate generator when you are tired or under the
influence of drugs, alcohol, or medication.
� Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
� Product users on United States Forest Service land, and
in some states, must comply with fire prevention regula-
tions. This product is not equipped with a spark arrestor.
Check with the federal, state, or local authorities in your
area before use.
 Do not touch bare wire or receptacles.
 Do not use generator with electrical cords which are
worn, frayed, bare, or otherwise damaged.
 Before storing, allow the engine to cool.
 Do not operate generator in rain, snow, or wet weather.
 Empty fuel tank, close fuel valve, and restrain the unit
from moving before transporting in a vehicle.
 Allow engine to cool for five minutes before refueling.
 To reduce the risk of fire and burn injury, handle fuel with
care. It is highly flammable.
 Do not smoke while handling fuel.
 Store fuel in a container approved for gasoline.
 Position the unit on level ground, stop engine, and allow
to cool before refueling.
 Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
 Tighten the fuel cap securely after refueling.
 Wipe spilled fuel from the unit.
 Never attempt to burn off spilled fuel under any circum-
stances.
 Use only authorized replacement parts and accessories
and follow instructions in the Maintenance section of this
manual. Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of shock or
injury.
 Maintain the unit per maintenance instructions in this
Operator’s Manual.
 Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace damaged parts.
 National Electric Code requires generator to be grounded
to an approved earth ground. Before using the ground
terminal, consult a qualified electrician, electrical inspec-
tor, or local agency having jurisdiction for local codes
or ordinances that apply to the intended use of the
generator.

Page 4
SPECIFIC SAFETY RULES
 Exhaust contains poisonous carbon monoxide, a color-
less, odorless gas. Breathing exhaust can cause loss
of consciousness and can lead to death. If running in a
confined or partially-enclosed area, the air may contain
a dangerous amount of carbon monoxide. To keep ex-
haust fumes from building up, always provide adequate
ventilation.
 Always use a battery-powered carbon monoxide detec-
tor when running the generator. If you begin to feel sick,
dizzy, or weak while using the generator, shut it off and
get to fresh air immediately. See a doctor. You may have
carbon monoxide poisoning.
 Place the generator on a flat, stable surface with a slope
of no more than 4°.
 Operate in a well-ventilated, well-lit area isolated from
working areas to avoid noise interference.
 Operating the generator in wet conditions could result in
electrocution. Keep the unit dry.
 Keep the generator a minimum of 3 feet away from all
types of combustible material.
 Do not operate generator near hazardous material.
 Do not operate generator at a gas or natural gas filling
station.
 Do not touch the muffler or cylinder during or immediately
after use; they are HOT and will cause burn injury.
 Do not connect to a building’s electrical system unless a
transfer switch has been properly installed by a qualified
electrician.
 To connect a generator to your existing wiring, notify
your utility company that you are installing a generator
for backup power. Then have a licensed electrical contrac-
tor install a transfer switch. The transfer switch isolates
your home from the ability to “back feed” neutral power
lines. Failure to isolate the generator from power utility
can result in death or injury to electric utility workers.
 Do not allow the generator’s gas tank to overflow when
filling. Fill to 1 in. below the top neck of the gasoline tank
to allow for fuel expansion. Check the ventilation hole in-
side the fuel tank cap for debris. Do not block the vent.
 Do not smoke when filling the generator with gasoline.
 Allow the engine to remain in a shut-down condition for
at least five minutes before adding gasoline or oil.
 Do not remove the oil dipstick or the fuel tank cap when
the engine is running.
 Pay close attention to all safety labels located on the
generator.
 Keep children a minimum of 10 feet away from the gen-
erator at all times.
 The unit operates best in temperatures between 23°F and
104°F with a relative humidity of 90% or less.
 Specific modifications for high-altitude performance
are needed if the generator will always be operated at
altitudes above 5,000 feet. Contact your nearest Baja
authorized service center for more information and to
have these modifications performed.
 Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also.

Page 5
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
hrs Hours Time
gal Gallon Volume
qt Quart Volume
Wet Conditions Alert Do not expose to rain or use in damp locations.
Read The Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Safety Alert Precautions that involve your safety.
Electric Shock Failure to use in dry conditions and to observe safe practices can
result in electric shock.
Toxic Fumes
Running generator gives off carbon monoxide, an odorless, color-
less, poison gas. Breathing carbon monoxide can cause nausea,
fainting, or death.
Fire/Explosion Fuel and its vapors are extremely flammable and explosive. Fire
or explosion can cause severe burns or death.
Hot Surface To reduce the risk of injury or damage, avoid contact with any hot
surface.
Lifting Hazard To reduce the risk of serious injury, avoid attempting to lift the
generator alone.
Ground Consult with local electrician to determine grounding requirements
before operation.
Electrocution Failure to properly ground generator can result in electrocution,
especially if the generator is equipped with a wheel kit.

Page 6
DANGER:
To avoid death or serious personal injury, do not attempt
to operate this product until you read thoroughly and
understand completely the operator’s manual. If you
do not understand the warnings and instructions in the
operator’s manual, do not use this product. Call Baja
customer service for assistance.
WARNING:
Observe all normal safety precautions related to avoid
electrical shock.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service, contact Baja Motorsports at 1-866-260-8280. When
servicing, use only identical replacement parts.
The operation of any products can result in foreign objects being thrown into your eyes, which can result in
severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked
to comply with ANSI Z87.1.
WARNING:
SYMBOLS
SAVE THESE INSTRUCTIONS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property
damage.

Page 7
SYMBOLS
SAFETY LABELS
The information below can be found on the generator. For
your safety, please study and understand all of the labels
before starting the generator.
If any of the labels come off the unit or become hard to read,
contact a Baja authorized service center for replacement.
This engine is equipped with an oil sensor.
Fill oil to upper level if failure to start.
FUEL WARNING
No smoking when filling with
gasoline. Do not overfill. Full level
is 1 in. below the top of the fuel
neck. Stop the engine for five
minutes before refueling to avoid
the heat from the muffler igniting
fuel vapors.
ENGINE OIL WARNING
You must add oil before first operating the generator. The oil
reservoir capacity is 1.2 qt. Always check the oil level before
each operation. The oil level should always register within
the hatched area on the dipstick. The unit is equipped with
an oil sensor which will automatically shut off the engine if
oil level falls below a safe limit.
HOT SURFACE
WARNING
Do not touch the
muffler or aluminum
cylinder of the engine.
They are very HOT
and will cause severe
burns. Don’t put any flammable or combustible materials in
the direct path of the exhaust.
VENTILATION WARNING
Do not use the generator in an enclosed area or near open
windows, vents, or doors. Fumes from the unit can kill.
GROUNDING
WARNING
National Electric
Code requires
generator to be
grounded to an
approved earth
ground.
WARNING
HOT
SURFACE

Page 8
ELECTRICAL
EXTENSION CORD CABLE SIZE
Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.
Inadequate size cables can cause a voltage drop, which can burn out the appliance and overheat the cord.
Current in
Amperes
Load in Watts Maximum Allowable Cord Length
At 120V At 240V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire
2.5 300 600 1000 ft. 600 ft. 375 ft. 250 ft.
5 600 1200 500 ft. 300 ft. 200 ft. 125 ft.
7.5 900 1800 350 ft. 200 ft. 125 ft. 100 ft.
10 1200 2400 250 ft. 150 ft. 100 ft. 50 ft.
15 1800 3600 150 ft. 100 ft. 65 ft.
20 2400 4800 175 ft. 125 ft. 75 ft.
25 3000 6000 150 ft. 100 ft.
30 3600 7200 125 ft. 65 ft.
40 4800 9600 90 ft.
ELECTRIC MOTOR LOADS
It is characteristic of common electric motors in normal operation to draw up to six times their running current while start-
ing. This table may be used to estimate the watts required to start “Code G” electric motors; however, if an electric motor
fails to start or reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check
the requirements of the tool or appliance being used compared to the rated output of the generator.
Motor Size (H.P.) Running Watts Watts Required to Start Motor
Repulsion Induction Capacitor Split Phase
1/8 275 600 850 1200
1/6 275 600 850 2050
1/4 400 850 1050 2400
1/3 450 975 1350 2700
1/2 600 1300 1800 3600
3/4 850 1900 2600 —
1 1100 2500 3300 —
GROUND FAULT CIRCUIT INTERRUPTER
The 20 amp, 120 volt receptacles on the generator are pro-
tected by a Ground Fault Circuit Interrupter (GFCI), which
guards against the hazards of ground fault currents. An
example of ground fault current is the current that would
flow through a person who is using an appliance with faulty
insulation and, at the same time, is in contact with an electrical
ground such as a plumbing fixture, wet floor, or earth.
GFCI receptacles do not protect against short circuits,
overloads, or shocks.
The GFCI receptacles can be tested with the TEST and
RESET buttons.
To test:
 Depress the TEST button. This should cause the Reset
button to pop out.
 To restore power, depress the RESET button.
Perform this test monthly to ensure proper operation of the
GFCI. If the generator is stored outdoors, unprotected from
the weather, test the GFCI receptacle before each use.
Fig. 1
RESET BUTTON TEST BUTTON

Page 9
ELECTRICAL
GENERATOR CAPACITY
Make sure the generator can supply enough continuous (run-
ning) and surge (starting) watts for the items you will power
at the same time. Follow these simple steps.
�1. Select the items you will power at the same time.
�2. Total the continuous (running) watts of these items. This
is the amount of power the generator must produce to
keep the items running. See the wattage reference chart
at right.
�3. Estimate how many surge (starting) watts you will need.
Surge wattage is the short burst of power needed to
start electric motor-driven tools or appliances such as a
circular saw or refrigerator. Because not all motors start
at the same time, total surge watts can be estimated by
adding only the item(s) with the highest additional surge
watts to the total rated watts from step 2.
Example:
Tool or Appliance Continuous
(Running) Watts
Surge
(Starting) Watts
Window AC,
10,000 BTU 1200 1800
Refrigerator 700 2200
1/3 HP Well Pump 1000 2000
27 in. Television 500 0
Light (75 Watts) 75 0
3475 Total
Running Watts
2200 Highest
Surge Watts
Total Continuous (Running) Watts 3475
Plus Highest Additional Surge Watts + 2200
Equals Total Generator Output Required 5675
POWER MANAGEMENT
To prolong the life of the generator and attached devices,
it is important to take care when adding electrical loads to
the generator. There should be nothing connected to the
generator outlets before starting its engine. The correct and
safe way to manage generator power is to sequentially add
loads as follows:
1. With nothing connected to the generator, start the engine
as described later in this manual.
2. Plug in and turn on the first load, preferably the largest
load you have.
3. Permit the generator output to stabilize (engine runs
smoothly and attached device operates properly).
4. Plug in and turn on the next load.
5. Again, permit the generator to stabilize.
6. Repeat steps 4 and 5 for each additional load.
Never add more loads than the generator capacity. Take
special care to consider surge loads in generator capacity
as previously described.
Tool or Appliance
Typical
Continuous*
(Running)
Watts
Typical
Surge
(Starting)
Watts
Essentials
Light Bulb − 75 Watt 75 75
Refrigerator/Freezer 700 2200
Sump Pump − 1/2 HP 1050 2200
Water Well Pump − 1/3 HP 1000 1500
Electric Water Heater 4000 0
Heating/Cooling
Furnace Fan − 1/2 HP 800 2350
Window AC − 10,000 BTU 1200 1800
Space Heater 1800 0
Kitchen
Microwave Oven − 1000 Watt 1000 0
Coffee Maker 1000 0
Electric Stove − Single Element 2100 0
Toaster Oven 1200 0
Family Room
VCR 100 0
CD/DVD Player 100 0
Stereo Receiver 450 0
Color Television − 27 in. 500 0
Other
Security System 500 0
Curling Iron 1500 0
Garage Door Opener − 1/2 HP 875 2350
Hair Dryer − 1/2 HP 1250 0
DIY/Job Site
Quartz Halogen Work Light 1000 0
Airless Sprayer − 1/3 HP 600 1200
Reciprocating Saw 960 0
Electric Drill − 1/2 HP 600 900
Circular Saw − 7-1/4 in. 1400 2300
Miter Saw − 10 in. 1800 1800
Planer/Jointer − 6 in. 1800 1800
Table Saw/Radial Arm Saw − 10 in. 2000 2000
Air Compressor − 1 HP 1600 4500
*Wattages listed are approximate. Check tool or appliance for actual wattage.
CAUTION:
Do not overload the generator’s capacity. Exceeding the
generator’s wattage/amperage capacity can damage the
generator and/or electrical devices connected to it.

Page 10
FUEL
AC CIRCUIT
BREAKER
PRODUCT SPECIFICATIONS
ENGINE
Engine Type ................................ 4 Stroke, Overhead Valve
Bore x Stroke ............................................. 88 mm x 64 mm
Cooling System .................................................. Forced Air
Compression Ratio ......................................................... 8:1
Starting System ......................................................... Recoil
Ignition System ............................................................T.C.I.
Spark Plug .................................................. TORCH F7RTC
Engine Oil Volume .....................................................1.2 qt.
Fuel Volume ............................................................. 6.5 gal.
FEATURES
Fig. 2
ENGINE
SWITCH
RECOIL STARTER
GRIP
AIR FILTER
CHOKE
LEVER
AC CIRCUIT
BREAKER
GROUND
TERMINAL
240 VOLT AC
30 AMP
RECEPTACLE
120 VOLT AC
20 AMP GFCI
RECEPTACLES
FUEL TANK
OIL CAP/ DIPSTICK
FUEL VALVE
FUEL LEVEL
GAUGE
OIL DRAINAGE
BOLT
FUEL CAP
GENERATOR
Rated Voltage .................................................... 120V/240V
Rated Amps ................................................................22.9A
Rated Output ..........................................................5,500 W
Maximum Output ...................................................6,000 W
Rated Frequency ........................................................60 Hz
DIMENSIONS
Length ................................................................... 32.67 in.
Width ..................................................................... 26.77 in.
Height ...................................................................... 24.6 in.
Net Weight .............................................................. 202 lbs.

Page 11
KNOW YOUR GENERATOR
See Figure 2.
The safe use of this product requires an understanding of the
information on the product and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
AC CIRCUIT BREAKER
The circuit breaker is provided to protect the generator against
electrical overload and can be used to turn the generator’s
electrical power on or off.
AIR FILTER
The air filter helps to limit the amount of dirt and dust drawn
into the unit during operation.
CHOKE LEVER
The choke lever is used when starting the engine.
ENGINE SWITCH
The engine switch is used in combination with the recoil
starter grip to start the generator. It is also used to turn the
generator off.
FUEL LEVEL GAUGE
Consult the fuel level gauge to determine the amount of fuel
remaining in the generator.
FUEL TANK
The fuel tank has a capacity of 6.5 gallons.
FUEL VALVE
The flow of fuel through the generator is controlled by the
position of the fuel valve.
GROUND TERMINAL
The ground terminal is used to assist in properly ground-
ing the generator to help protect against electrical shock.
Consult with a local electrician for grounding requirements
in your area.
OIL DRAINAGE BOLT
When changing the engine oil, the oil drainage bolt is loos-
ened to allow old engine oil to be drained.
OIL CAP/DIPSTICK
Remove the oil fill cap to check and add oil to the generator
when necessary.
RECEPTACLES
Your generator has the following single phase, 60 Hz outlets:
four 120 Volt AC, 20 Amp GFCI receptacles, and one 240
Volt AC, 30 Amp receptacle. These can be used for operat-
ing appropriate appliances, electrical lighting, tools, and
motor loads.
RECOIL STARTER GRIP
The recoil starter grip is used (along with the engine switch)
to start the generator’s engine.
FEATURES

Page 12
LOOSE PARTS LIST
Key
No. Description ....................................................Qty.
1 Wheels .................................................................2
2 Wheel Axle ...........................................................2
3 Large Cotter Pin ..................................................2
4 Small Cotter Pin ..................................................4
5 Clevis Pin .............................................................2
6 Handle .................................................................2
The following items are included with the generator:
Key
No. Description ....................................................Qty.
7 Bolt ......................................................................6
8 Frame Support with Foot ....................................2
10W-30 4-Cycle Engine Oil
(34 fl. oz., not shown) ..........................................1
Registration Card (not shown) .............................1
Operator’s Manual (not shown) ...........................1
1
8
7
6
2
5
34

Page 13
ASSEMBLY
UNPACKING
This product requires assembly.
 Remove one end of the box and carefully slide out the
generator and any accessories.
NOTE: The generator is heavy. If you must lift the unit
out of the box, get another person to help you and lift
with your legs, not your back.
 Inspect the unit carefully to make sure no damage oc-
curred during shipping.
 Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
 If any parts are damaged or missing, please call
1-866-260-8280 for assistance.
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Failure to heed
this warning could result in serious personal injury.
WARNING:
Do not attempt to modify this tool or create accessories not
recommended for use with this tool. Any such alteration
or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
WARNING:
Do not attempt to operate the generator until assembly
is complete. Failure to comply could result in possible
serious personal injury.
INSTALLING THE WHEELS
See Figure 3.
Wheels are provided to assist in moving the generator to the
desired location and should be installed on the side opposite
the recoil starter.
NOTE: Install the wheels before installing the handle. Do not
put fuel or oil in the generator before installing the wheels.
 Locate the following items:
2 wheel axles 2 wheels
2 small cotter pins 2 large cotter pins
 Raise the end of the generator opposite the recoil starter
high enough to gain access to the frame bottom; securely
position props underneath to support.
 Locate the U-bracket on one side of the frame bottom.
Slide a wheel axle through the bracket so that an end
extends from both sides of the bracket.
 On the end that extends inside the generator frame, insert
a small cotter pin through the hole in the axle to secure.
Bend the ends of the cotter pin to prevent the pin from
slipping out.
 Place a wheel over the other end of the axle.
 Insert a large cotter pin through the hole in the axle. Bend
the ends of the pin to secure.
 Repeat the process on the other side.
INSTALLING THE FRAME SUPPORTS
See Figure 4.
Install the two frame supports provided on the bottom side
of the generator frame opposite the wheels.
 Locate the following items:
2 frame supports 6 bolts
 Raise the end of the generator where the recoil starter is
located high enough to gain access to the frame bottom;
securely position props underneath to support.
 Align the holes on the frame support with the holes on
the generator frame.
 Insert a bolt through the hole in the generator frame so it
extends down through the frame support.
 Tighten bolt to secure.
 Repeat with the two remaining screws.
 Repeat on other side to install second frame support.
FRAME SUPPORT
WITH FOOT
Fig. 3
Fig. 4
WHEEL
AXLE
SMALL
COTTER
PIN
WHEEL
U-BRACKET
LARGE
COTTER
PIN
HOLE
BOLT

Page 14
OPERATION
DANGER:
Failure to properly ground generator can result in elec-
trocution, especially if the generator is equipped with a
wheel kit. National Electric Code requires generator to be
properly grounded to an approved earth ground. Call an
electrician for local grounding requirements.
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is suf-
ficient to inflict serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATIONS
This generator is designed to supply electrical power for
operating compatible electrical lighting, appliances, tools,
and motor loads.
ASSEMBLY
Fig. 5
GENERATOR
FRAME
COTTER PIN
HANDLE
CLEVIS PIN
INSTALLING THE HANDLES
See Figure 5.
 Locate the following items:
2 handles 2 clevis pins
2 small cotter pins
 With the generator in normal operating position, find the
holes on the frame above the recoil starter.
 Align the holes in one of the handle brackets with the
holes in one side of the generator frame.
 Insert a clevis pin through the handle bracket and frame.
The head of the pin should be on the outside of the
frame.
 Insert the small cotter pin through the hole in the clevis
pin. Bend the ends of the pin to secure.
 Repeat the above steps to install the second handle.
CAUTION
Do not attempt to lift the unit by the handle assembly.
If it is necessary to lift the generator, always grasp by
the frame. Use proper lifting techniques to avoid back
injury.

Page 15
FUEL
AC CIRCUIT
BREAKER
Fig. 6
Fig. 7
OIL CAP/
DIPSTICK
OIL FILL
HOLE
FUEL LEVEL
GAUGE
FUEL TANK
FUEL CAP
OPERATION
BEFORE OPERATING THE UNIT
Position the generator on a flat surface before checking fluid
levels or adding fluid.
CAUTION:
Attempting to start the engine before it has been properly
filled with oil will result in equipment failure.
CHECKING/ADDING OIL
See Figure 6.
Engine oil has a major influence on engine performance and
service life. For general, all-temperature use, SAE 10W-30 is
recommended. Always use a 4-stroke motor oil that meets or
exceeds the requirements for API service classification SJ.
NOTE: Non-detergent or 2-stroke engine oils will damage
the engine and should not be used.
 Unscrew the oil cap/dipstick and remove.
 Wipe dipstick clean and re-seat in hole; do not re-
thread.
 Remove dipstick again and check oil level. Oil level should
fall within the hatched area on the dipstick.
 If level is low, add engine oil until the fluid level rises to
the upper portion of the hatched area on the dipstick.
 Replace and secure the oil cap/dipstick.
CHECKING/ADDING FUEL
See Figure 7.
 Check the fuel level gauge. If fuel is needed, continue
with the next step.
 Remove the fuel cap.
 Fill the fuel tank to 1 in. below the top of the fuel neck.
 Replace and secure the fuel cap.
NOTE: Always use unleaded gasoline with a pump octane
rating of 86 or higher. Never use old, stale, or contaminated
gasoline, and do not use an oil/gas mixture. Do not allow
dirt or water into the fuel tank.
USING FUEL STABILIZER
Fuel gets old, oxidizes, and breaks down over time. Add-
ing a fuel stabilizer extends the usable life of fuel and helps
prevent deposits from forming that can clog the fuel system.
Follow fuel stabilizer manufacturer’s directions for correct
ratio of stabilizer to fuel.
 Add stabilizer to fuel tank, then fill with gasoline following
previous instructions.
NOTE: Fuel stabilizer and gasoline can be mixed prior
to filling the tank by using a gas can or other approved
fuel container and shaking gently to combine.
 Replace and secure the fuel tank cap.
 Start and run the engine for at least 5 minutes to allow
stabilizer to treat the entire fuel system.
OXYGENATED FUELS
Some conventional gasolines are blended with alcohol or an
ether compound. These gasolines are collectively referred
to as oxygenated fuels. To meet clean air standards, some
areas of the United States and Canada use oxygenated fuels
to help reduce emissions.

Page 16
FUEL
AC CIRCUIT
BREAKER
ENGINE
SWITCH
CIRCUIT
BREAKER
RECOIL
STARTER
GRIP
PUSH CHOKE
LEVER IN TO RUN
PULL CHOKE
LEVER OUT
TO START
If using an oxygenated fuel, make sure it is unleaded and
meets the minimum octane rating requirements. Before using
an oxygenated fuel, try to confirm the fuel’s contents. Some
states/provinces require this information to be posted on the
pump. The following are the EPA approved percentages of
oxygenates:
Ethanol (ethyl or grain alcohol) 10% by volume. You
may use gasoline containing up to 10% ethanol by volume.
Gasoline containing ethanol may be marketed under the
name “Gasohol.”
MTBE (methyl tertiary butyl ether) 15% by volume. You
may use gasoline containing up to 15% MTBE by volume.
Methanol (methyl or wood alcohol) 5% by volume. You
may use gasoline containing up to 5% methanol by volume
as long as it also contains cosolvents and corrosion inhibi-
tors to protect the fuel system. Gasoline containing more
than 5% methanol by volume may cause starting and/or
performance problems. It may also damage metal, rubber,
and plastic parts of the generator or your fuel system.
If you notice any undesirable operating symptoms, try another
service station or switch to another brand of gasoline.
NOTE: Fuel system damage or performance problems re-
sulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated previously are
not covered under warranty.
CAUTION:
On a level surface with the engine off, check the oil level
before each use of the generator.
STARTING THE ENGINE
See Figures 8 - 10.
NOTE: If location of generator is not level, the unit may not
start or may shut down during operation.
 Unplug all loads from the generator.
 Switch the AC circuit breakers to the OFF ( O ) position.
 Turn the fuel valve to the ON position.
 Pull the choke lever to the START position.
NOTE: If engine is warm or the temperature is above
50˚F, push the choke lever in to the RUN position.
 Put the engine switch in the ON ( I ) position.
 Pull the recoil starting grip until the engine runs (a maxi-
mum of 6 times).
NOTE: Do not allow the grip to snap back after starting;
return it gently to its original place.
 Allow the engine to run for 30 seconds, then push the
choke lever in to the RUN position.
 Switch the AC circuit breakers to the ON position.
OPERATION
Fig. 8
Fig. 9
Fig. 10
STOPPING THE ENGINE
See Figures 8 - 9.
To stop the engine under normal operating conditions:
 Remove any load from the generator.
 Place the voltage selector in the center (OFF) position.
 Switch the AC circuit breakers to the OFF position.
 Turn the fuel valve to the OFF position.
 Put the engine switch in the OFF ( O ) position.
To stop the engine in an emergency situation:
 Put the engine switch in the OFF ( O ) position.
FUEL
VALVE

Page 17
FUEL
AC CIRCUIT
BREAKER
WARNING:
When servicing, use only identical Homelite replacement
parts. Use of any other parts may create a hazard or
cause product damage.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a Baja authorized service center.
GENERAL MAINTENANCE
Keep the generator in a clean and dry environment where it
is not exposed to dust, dirt, moisture, or corrosive vapors.
Do not allow the cooling air slots in the generator to become
clogged with foreign material such as leaves, snow, etc.
Do not use a garden hose to clean the generator. Water en-
tering the fuel system or other internal parts of the unit can
cause problems that will decrease the life of the generator.
To clean the unit:
 Use a soft bristle brush and/or vacuum cleaner to loosen
and remove dirt and debris.
 Clean air vents with low pressure air that does not exceed
25 psi.
 Wipe the exterior surfaces of the generator with a damp
cloth.
CHECKING/CLEANING AIR FILTER
See Figure 11.
For proper performance and long life, keep air filter clean.
 Rotate the knob counterclockwise to release.
 Lift the air filter cover toward you and up to remove from
the air filter unit.
 Remove the filter element.
 If the filter element is dirty, clean with warm, soapy water.
Rinse and let dry.
 Apply a light coat of engine oil to the elements, then
squeeze it out.
 Replace the element in the air filter unit.
 Replace the air filter cover.
 Reinstall the knob and rotate clockwise to secure.
NOTE: Do not run the generator without the air filter. Rapid
engine wear will result.
CHANGING ENGINE OIL
See Figure 12.
 Remove the oil cap/dipstick.
 Place a container underneath the oil drainage bolt to
collect used oil as it drains.
 Unscrew the oil drainage bolt and remove.
 Allow oil to drain completely.
 Reinstall the oil drainage bolt and tighten securely.
 Refill with oil following the instructions in the Checking/
Adding Oil section.
 Reinstall the oil cap/dipstick.
NOTE: Used oil should be disposed of at an approved dis-
posal site. See your local oil retailer for more information.
MAINTENANCE
Fig. 12
Fig. 11
KNOB FILTER
ELEMENT AIR FILTER
UNIT
OIL DRAINAGE
BOLT
OIL CAP/
DIPSTICK
AIR FILTER
COVER

Page 18
CLEANING FUEL SEDIMENT CUP
See Figure 13.
The sediment cup prevents dirt and water that may have
gotten into the fuel tank from entering the carburetor. If the
engine has not been run for a long time, the sediment cup
should be cleaned before use.
 Turn the fuel valve to the OFF position.
 Remove the sediment cup using a 10 mm wrench (not
provided).
 Remove the O-ring and filter.
 Clean each of the parts in carburetor cleaner or any
comparable cleaning product.
 Reinstall the filter, O-ring, and sediment cup. Tighten with
wrench to secure.
 Return the fuel valve to ON position and check for
leaks.
SPARK PLUG MAINTENANCE
See Figure 14.
The spark plug must be properly gapped and free of deposits
in order to ensure proper engine operation. To check:
 Remove the spark plug cap.
 Clean any dirt from around base of spark plug.
 Remove spark plug using wrench provided.
 Inspect spark plug for damage, and clean with a wire
brush before reinstalling. If insulator is cracked or chipped,
spark plug should be replaced.
NOTE: If replacing, use the following recommended
spark plugs or equivalent: Champion RN9YC or NGK
BPR5ES.
 Measure plug gap. The correct gap is 0.028−0.031 in.
(0.7-0.8 mm). To widen gap, if necessary, carefully bend
the ground (top) electrode. To lessen gap, gently tap
ground electrode on a hard surface.
 Seat spark plug in position; thread in by hand to prevent
cross-threading.
 Tighten with wrench to compress washer. If spark plug
is new, use 1/2 turn to compress washer appropriate
amount. If reusing old spark plug, use 1/8 to 1/4 turn for
proper washer compression.
NOTE: An improperly tightened spark plug will become
very hot and could damage the engine.
MAINTENANCE
Fig. 14
Fig. 13
SPARK
PLUG
SPARK
PLUG
CAP
SEDIMENT
CUP
FUEL
VALVE
O-RING
FILTER

Page 19
MAINTENANCE
CLEANING THE EXHAUST PORT AND
MUFFLER
Depending on the type of fuel used, the type and amount of
oil used, and/or your operating conditions, the exhaust port
and muffler may become blocked with carbon deposits. If
you notice a power loss with your gas-powered tool, you
may need to remove these deposits to restore performance.
We highly recommend that only qualified service technicians
perform this service.
SPARK ARRESTOR
Product users on United States Forest Service land, and in
some states, must comply with fire prevention regulations.
This product is not equipped with a spark arrestor. To pur-
chase a spark arrestor for the generator, contact Baja cus-
tomer service at 1-866-260-8280 and request part number
H60-130.
DRAINING FUEL TANK/CARBURETOR
See Figures 15 - 16.
When not using a fuel stabilizer, draining the fuel from the
tank and carburetor before storage may help prevent gum
deposits in the fuel system.
DRAINING THE FUEL TANK
 Turn the engine switch OFF ( O ).
 �Close fuel valve.
� Remove the fuel line from the petcock by squeezing the
ends of the retaining clip and sliding the fuel line off.
 Install one end of a drain line over the petcock, and place
the other end in a fuel container large enough to catch
the fuel being drained from the tank.
 Open fuel valve.
 When the fuel has drained from the tank, close the fuel
valve and reinstall fuel line on petcock.
DRAINING THE CARBURETOR
 Turn the engine switch OFF ( O ).
 Close the fuel valve.
 Position a suitable container under the carburetor drain
screw to catch fuel; loosen the screw.
 Allow fuel to drain completely into container.
 Retighten drain screw.
Fig. 15
Fig. 16
FUEL
LINE FUEL
VALVE
CARBURETOR
DRAIN SCREW
NOTE: Consult hazardous waste management guidelines in
your area for the proper way to dispose of used fuel.
TRANSPORTING
 Turn engine switch OFF ( O ).
 Close the fuel valve.
 Make sure engine and exhaust of unit is cool.
 Keep unit level to prevent fuel spillage.
 Do not drop or strike unit or place under heavy objects.
PETCOCK

Page 20
STORAGE
When preparing the generator for storage, follow the guidelines below.
STORAGE TIME PRIOR TO STORING
Less than 1 month  No special preparation is required.
1 to 2 months  Fill with fresh gasoline and add a gasoline stabilizer*.
2 months to 1 year  Fill with fresh gasoline and add a gasoline stabilizer*.
 Drain fuel from carburetor.
 Clean fuel sediment cup.
1 year or more  Fill with fresh gasoline and add a gasoline stabilizer*.
 Drain fuel from the carburetor.
� Clean fuel sediment cup.
� Remove spark plug.
 Put a tablespoon of engine oil into the spark plug cylinder. Turn the engine slowly with the pull
rope to distribute the oil.
� Reinstall spark plug.
 Change engine oil.
After removal from storage:
 Drain and dispose of stored gasoline in a suitable container.
 Fill with fresh gasoline.
*Use gasoline stabilizers formulated to extend storage life. For recommendations, contact your nearest Baja authorized
service center.
MAINTENANCE
MAINTENANCE SCHEDULE
Before
each use
After 1st month
or 20 hours of
operation
Every 3 months
or 50 hours of
operation
Every 6 months
or 100 hours
of operation
Every year or
after 300 hours
of operation
Check Engine Oil 
Change Engine Oil  
Check Air Filter 
Clean Air Filter 
Change Air Filter 
Clean Carburetor
Sediment Cup 
Check/Adjust Spark Plug 
Replace Spark Plug 
Check/Adjust Idle Speed 
Check/Adjust Valve
Clearance* 
Clean Fuel Tank and
Filter* 
Check Fuel Tube 
* These items should only be carried out by a Baja authorized service center.
NOTE: Maintenance should be performed more frequently when generator is used in dusty areas.
When generator has exceeded the maximum figures specified in the table, maintenance should still be cycled
according to the intervals of time or hours stated herein.