Homeroots 286587 User manual

ASSEMBLY INSTRUCTIONS
MODEL: 02091 PAGE 1 OF 6
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
BED PARTS
HARDWARE PARTS
№
DESCRIPTION
QTY
№
DESCRIPTION
QTY
A Left Side Panel 1 Pc 1
Hex-Head 5/16”X45mm Bolts
9 Pcs
2 Hex-Head 1/4”X75mm Bolts 8 Pcs
B Right Side Panel 1 Pc 3 Hex-Head 1/4”X60mm Bolts 16 Pcs
4 Hex-Head 5/16”X35mm Bolts 4 Pcs
C Cross Braces 2 Pcs 5 1/4”Curved Washers 24 Pcs
D Top Frame 1 Pc 6
Hex-Head 1/4“x20mm Bolts 8 Pcs
7 5/16”Curved Washers 8 Pcs
E Upper Futon Frame 1 Pc 8
1/4”Washers 8 Pcs
9 1/4”Nuts 8 Pcs
F Lower Futon Frame
(with 2 Handles) 1 Pc 10 C-Hook 2 Pcs
11 Protective Pads 4 Pcs
G Guardrails 2 Pcs 12
￠5/16”Washers 12 Pcs
H Left Hinge 1 Pc 13 ￠5/16”Nuts 12 Pcs
I Right Hinge 1 Pc 14 11#、13# Open Wrench 2 Pcs
M Supporting leg 1 Pc 15
4#、5# Allen Wrenches 2 Pcs
16 Plastic pad 4 Pcs
17 Safety Hook 1 Pc
MODEL: 286587, 286586, 286585, 286584, 285193, 285192, 285191, 285190

ASSEMBLY INSTRUCTIONS
MODEL: 02091 PAGE 2 OF 6
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
STEP 1:
STEP 2:
MODEL: 286587, 286586, 286585, 286584, 285193, 285192, 285191, 285190

ASSEMBLY INSTRUCTIONS
MODEL: 02091 PAGE 3 OF 6
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
STEP 3:
STEP 4:
Remark:
Please always keep the warning lable on the inside of the upper bed end structure
permanently.
MODEL: 286587, 286586, 286585, 286584, 285193, 285192, 285191, 285190

ASSEMBLY INSTRUCTIONS
MODEL: 02091 PAGE 4 OF 6
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
REMARK: PART 17—SAFETY HOOK
lAlways use the safety hook to fix Lower Futon Frame (Part F) and Cross Braces (Part C)
together once you have placed Futon in horizontal or seat.
lAdult assembly required.
lIf you need to switch from futon to full bed, you will have to remove the
hook first before place the futon down！
MODEL: 286587, 286586, 286585, 286584, 285193, 285192, 285191, 285190

ASSEMBLY INSTRUCTIONS
MODEL: 02091 PAGE 5 OF 6
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
Size of Mattress
This bed is designed to use a mattress 74”x 37-1/2”–38-1/2”on the upper bunk and 74”x 53-
1/2”
–54”on the lower bunk. The thickness of the mattress must not exceed 6”
on the upper bunk. There
must be at least 5”from mattress sleeping surface to top edge of guard rail on the upper bunk.
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any of our retail dealers.
Additional Note
Maximum total weight not to exceed 150 lbs. on the upper bunk, and maximum 200 lbs. on the lower
bunk.
SAFETY WARNINGS
(
ASTM
F1427
-
13)
1. Follow the information on the warnings appearing on the upper bunk end
structure and on the carton. Do not remove warning label from bed.
2. Always use the recommended size mattresses or mattress supports, or both, to
help prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of
guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Periodically check and ensure that the guardrail, ladder, and other components
are in their proper position, free from damage, and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
7. Always use the ladder for entering and leaving the upper bunk.
8. Do not use substitute parts. Contact the manufacturer or dealer for replacement
parts.
9. Use of a night light may provide added safety precaution for a child using the
upper bunk.
10. Always use guardrails on both long sides of the upper bunk. If the bunk bed will
be placed next to the wall, the guardrail that runs the full length of the bed should
be placed against the wall to prevent entrapment between the bed and wall.
11. The use of water or sleep flotation mattresses is prohibited.
12. STRANGULATION HAZARD–Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed; for example, but not limited
to, hooks, belts and jump ropes.
13. Keep these instructions for future reference.
14. Prohibit more than one person on upper bunk.
15.
Adult assembly required due to the presence of small parts ,sharp points,sharp
edgesas recesived.
MODEL: 286587, 286586, 286585, 286584, 285193, 285192, 285191, 285190

ASSEMBLY INSTRUCTIONS
MODEL: 02091 PAGE 6 OF 6
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
SAFETY WARNINGS
(
16 CFR 1513
)
(1) Do not allow children under 6 years of age to use the upper bunk.
(2) Use guardrails on both sides of the upper bunk.
(3) Prohibit horseplay on or under beds.
(4) Prohibit more than one person on upper bunk.
(5) Use ladder for entering or leaving upper bunk.
(6) If the bunk bed will be placed next to a wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between the bed and
the wall. (This applies only to bunk beds without two full-length guardrails.)
MODEL: 286587, 286586, 286585, 286584, 285193, 285192, 285191, 285190