HomeSpot HS3 NS002 User manual

HomeSpot® Bluetooth Adapter for
NSwitch
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks
by HomeSpot® is under license.
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other
countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the
United States and other countries.

Package Contents
Pouch Warranty Card
User Guide USB-C to USB-A
Adapter
HomeSpot HS3 NS002

About your HomeSpot HS3 NS002
USB-C Plug
P1 Button
Press to Connect or Toggle Internal Mic / Hold to Pair
P1 LED
Green = Connected with Mic Off
Amber = Connected with Mic On
Flashing Green = Connecting or Pairing
Codec LED
Off = SBC / Blue = aptX / Amber = aptX Low Latency
P2 LED
Green = Connected with Mic Off
Amber = Connected with Mic On
Flashing Green = Connecting or Pairing
P2 Button
Press to Connect or Toggle Internal Mic / Hold to Pair
Internal Mic

Setting up your hardware
1. Turn on the NSwitch and go to the Home menu.
2. Insert the HomeSpot HS3 NS002 into the NSwitch USB-C port.
3. LED indictors on the HomeSpot HS3 NS002 will start flashing.
4. HomeSpot HS3 NS002 is ready for pairing and connecting with your
headphones once the LEDs have stop flashing.
5.
For in-game voice chat, after headphones is paired and connected, press the
P1/P2 button to toggle the Internal Mic On/Off. When the Internal Mic is Off,
P1/P2 LED is Green. When the Internal Mic is On, P1/P2 LED is Amber.

Connecting to one Bluetooth headphones
1. Upon powering up, HomeSpot HS3 NS002 automatically enters pairing
mode on first use.
2. Make sure the Bluetooth headphones is in pairing mode.
3. Keep the headphones close to the HS3 NS002 during initial pairing.
4. Once connected, P1/P2 LED will be Green and headphones will start
receiving audio from the NSwitch.

Connecting to two Bluetooth headphones
1. Pair and connect to the first headphones, P1 LED will be Green.
2. Pair the 2nd headphones by pressing the P2 button for 3 seconds.
3. Keep the 2nd headphones close to the HS3 NS002 during initial pairing.
4. Once both headphones are connected, both P1 and P2 LEDs will be Green.
5. Both headphones will start receiving audio from the NSwitch.

. Manual re-connect
You may also manually initiate a re-connect by pressing either the P1 or P2
button, the corresponding previously paired 1st or 2nd headphones will be
re-connected respectively.
Reconnecting to a previously paired headphones
In-game Voice Chat
1. Make sure one or both headphones are paired and connected to the
HomeSpot HS3 NS002.
2. Press the P1/P2 button to toggle the Internal Mic On/Off. When Internal Mic
is Off, P1/P2 LED is Green. When Internal Mic is On, P1/P2 LED is Amber.
. Automatic re-connect
When a previously paired headphones is turned on, it will automatically
re-connect to the HomeSpot HS3 NS002.
Factory Reset
1. Power on the Nintendo Switch and go to the Home menu.
2. Insert the Bluetooth adapter into the bottom USB-C port on the Switch.
3. Press and hold both P1 and P2 buttons for 5 seconds until all LEDs start
flashing.

The HomeSpot HS3 NS002 can also be used with the TV dock. Simply plug the
bundled USB-C to USB-A adapter to the USB-A port on the side of the TV dock,
then insert the HS3 NS002 into USB-C port on the adapter.
Follow the previous pairing procedures for headphones connection.
TV Mode
* For regular NSwitch only

LED Indicators
Colored-line box – LED OnLED Off Dashed box – LED flashing
Status
All LEDs OffOff / Standby
P1 & Codec LEDs flashing alternatelyP1 Pairing
P2 LED flashingP2 Connecting
P1 LED GreenP1 Connected and Internal Mic Off
P1 LED AmberP1 Connected and Internal Mic On
P2 LED GreenP2 Connected and Internal Mic Off
P2 LED AmberP2 Connected and Internal Mic On
Codec LED OffAudio streming in SBC
Codec LED BlueAudio streming in aptX
Codec LED AmberAudio streming in aptX Low Latency
LEDs flashing from left to rightPowering up
LEDs
P1 Codec P2
P1 LED flashingP1 Connecting
P2 & Codec LEDs flashing alternatelyP2 Pairing

Safety Instructions
. Do not use this device in medical facilities, aircraft, refueling points, close to
automatic doors, automatic fire alarms or other remotely controlled devices.
. Keep this device at least 20 cm from pacemakers and other medical devices
as Bluetooth signal may interfere with their operation.
Product Specifications
Operating Frequency
Supported Bluetooth Profiles
Supported Codecs
Operating Range
Operating Temperature Range
Bluetooth version
2402 – 2408MHz
AD2P, HFP
aptX Low Latency, aptX, SBC
Up to 10 meters line of sight
0˚C to 45˚C
Bluetooth 5.0