Homewerks Worldwide AQUA VISTA 10SHO1H-CH-AV User manual

11-27-2019Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • HomewerksWW.com
TUB AND SHOWER FAUCET
10SHO1H-CH-AV – Polished chrome nish
PACKAGE AND HARDWARE CONTENTS
PART DESCRIPTION QUANTITY
A
B
C
D
E
G
F
H
A Shower head 1
B Shower arm 1
CShower arm ange 1
DHot handle assembly 1
ECold handle assembly 1
FTub spout with diverter 1
GHandle anges 2
HValve body 1
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water
supply lines.
CAUTION
• If you solder the joints during installation, the seats, cartridges, and washers
must be removed before using a ame or the warranty will be voided on
these parts.
• Cover the drain to avoid losing parts.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package and hardware contents list. If any part is missing or damaged,
do not attempt to assemble the product. Contact customer service for
replacement parts.
Estimated Assembly Time: 30 minutes
Tools required for assembly (not included): adjustable wrench, thread sealant
tape, strap wrench, Phillips head screwdriver, silicone
Installation may vary depending on how the previous tub and/or shower faucets
were installed. Supplies necessary for the installation of the product are not all
included; however, they are available wherever plumbing supplies are sold.
Prior to beginning installation, turn off the hot and cold water lines, then turn on
the old faucet to release built-up pressure. When installing the new tub and/or
shower faucets, hand tighten the connector nuts. DO NOT OVERTIGHTEN.
Connections that are too tight will reduce the integrity of the system.
Need Help? Please call our toll-free line at [phone] (7:30 am to 4:30 pm CST) for additional assistance or service.

2
PRODUCT SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS
Showerhead Max. Flow Rate: 1.8 GPM (6.8 LPM) at 80 PSI Polished chrome nish
ASME A112.18.1/CSA B125 Washerless cartridges
ASSEMBLY INSTRUCTIONS
1. Turn off water at the supply valve
under the sink or at the main water
supply, disconnect the supply line,
and remove old faucet.
Verify that the hole sizes and positions
in the wall are correct.
IMPORTANT: Complete valve
replacement is required for this tub/
shower unit. An access hole must be
cut with enough room to install the
new tub/shower valves inside the wall.
Professional installation is recom-
mended.
CAUTION: Do not use PEX tubing
for pipe from the valve to the tub
spout.
14. Installing the supply
connections:
Wrap thread sealant tape around
the valve body (H) threads in a
clockwise direction, as shown.
Thread the waterline (4.1) to
the valve body (H), and tighten
with a wrench.
NOTE: Be sure to position the
valve body (H) corretly in the wall,
with the markings “UP” facing
upward. Hot water supply lines go
into the H inlet and cold water
supply lines go into the C inlet. Cold
Hot 4.1
H
4
2. NOTE: The shower outlet hose
should be 1-1/4 in. in diameter.
For the cold water inlet (the right
side) and the hot water inlet (the left
side), cut or leave a 1-3/8 in. to 2 in.
diameter hole (recomended size is
1-3/4 in.). The center to center
distance between the cold and hot
water inlets should be 8 in.
1-3/8 in. ~ 2 in.
1-3/8 in. ~ 2 in.
8 in. Min.
48 in.
Tub & Shower
30 in.
Tub & Shower
8 in.
25. Installingthetubandshower
outlet connections:
Wrap thread sealant tape around
the pipe threads in a clockwise
direction, as shown. Connect the
shower (5.1) (not included) and
tube outlet pipes (5.2) (not
included) to the valve body (H).
Connect the pipe elbows (5.3)
(not included) to the ends of both
pipes, and tighten with a wrench.
NOTE: Do not use PEX or
CPVC between the valve and
spout.
Shower 5.3
5.1
H
5.2
Tub
5
3. IMPORTANT: Do not disassemble
the the cartridges during normal
installation.
When reinstalling the cartridge, be
sure to insert with the cartridge slot
(3.1 & 3.2) pointed outward as
shown. This is necessary for proper
operation of the valve.
3.1
3.2
36. Flushing the water outlets
and checking for leaks:
NOTE: Turn water supply back
on.
Turn on the hot and cold water
supply line, allowing water to ow
from the tub spout outlet (6.1)
until all debris is cleared from
the line.
Check all connections for leaks.
6
6.1
HomewerksWW.com

3
ASSEMBLY INSTRUCTIONS
7. Showerhead installation:
Insert the long end of the shower arm
(B) through the ange (C), then wrap
thread sealand tape around the long
end of the shower arm (B) in a
clockwise direction, as shown. Install
the long end of the shower arm (B)
into the pipe elbow inside the wall.
The ange (C) should t snug to the
nished wall surface. Thread the
shower head (A) onto the shower
arm (B). Carefully tighten the shower
arm (B) and shower head (A) with a
clean strap wrench. DO NOT
OVERTIGHTEN, as it could cause
damage to the shower arm (B).
B
C
A
79. Handle installation:
NOTE: Before proceeding, ensure
the valves are closed.
Position the anges (G) on the
valve body (H). Place the handles
(D & E) onto the valve body (H)
and secure them with the screws
(9. 1). Make sure the H (hot) handle
is on the left and the C (cold) handle
is on the right. Use a Phillips
screwdriver (not included) to
tighten the screws (9.1). Insert
the index buttons (9.2) into the
handles (D & E).
G
D
9.1 H
9.
2
E
9.1
9.2
G
9
8. Tub Spout Installation:
Wrap thread sealant tape around
the pipe threads of the tub spout
outlet (F) in a clockwise direction,
as shown. Connect the tub spout
outlet pipe (the tub spout outlet
pipe should project 3-15/16 in. to
4-3/32 in. from the nished wall)
to the lower pipe elbow (8.1) (not
included). Tighten the elbows (8.1)
and tub spout outlet pipe connec-
tions (8.2) with a strap wrench (not
included). Thread the spout (F) onto
the tub spout outlet pipe connec-
tion (8.2) in a clockwise direction
until the tub spout (F) becomes
ush with the nished wall. Use a
strap wrench to tighten the tub
spout (F).
F8.1
8.2 Wall
3-15/16 in. to
4-3/32 in.
8
OPERATING INSTRUCTIONS
The handles control the ow of hot and cold water to the faucet.
Turn the right handle for cold water. Turn the left handle for hot water. Rotating the handles opens the cartridges and causes water to ow from the spout. The degree of
handle rotation determines the volume of water ow. Returning the handles to the original position stops the ow of water.
CARE AND MAINTENANCE
Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the nish and void your warranty.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Leaks from the spout Damaged or dirty valve seat. Remove faucet handle, cartridge, housing and valve spool to check the rubber
valve seal. Clean it or replace by calling Customer Service.
Leaks from underneath the
handle
Bonnet is loose or bottom gasket on
cartridge is dirty or twisted. Remove the faucet handle. Tighten the bonnet. Clean or replace the O-ring.
HomewerksWW.com

4
ROUGH-IN
1/2"-14NPT
1/2"-14NPT
2-3/4"
11-1/8"
3-1/8"
5-3/8"
2-1/2"
8-3/8"
6-1/4"
6"
REPLACEMENT PARTS
For replacement parts, call our customer service department at [phone], 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
PART DESCRIPTION PART #
1
2
3
4
5
6
7
8
12
9
10
11
1Hot index button RP10028
2Cold index button RP10029
3Screw RP50013
4Handle RP13090
5Handle ange and washer RP80387CH
6Bonnet RP70154CH
7Cartridge RP22018
8Diverter RP70160
9Shower ange RP38046CH
10Shower arm RP38019CH
11 Showerhead RP38306CH
12Tub spout RP33052CH
LIMITED LIFETIME WARRANTY
The distributor warrants to the original consumer purchaser this product to be free from
defects in material and workmanship under normal use in residential applications. At its
option, the Company will provide repair parts or replace defective product when the
product is used in accordance with the manufacturer’s specications.
Use of mild abrasive, abrasive or chemical cleaners may damage the nish of the faucet. We
recommend cleaning your faucet with a soft cloth, moistened with water. Damage resulting
from the use of abrasive or chemical cleaners SHALL VOID THIS WARRANTY.
This warranty is not applicable to any products or parts of products where damage is caused
by use of non-genuine parts; is due to installation error, product misuse, negligence or faulty
maintenance; or where the product is not installed according to local building codes.
This warranty excludes labor charges or damage incurred during installation, repair or
replacement, and any indirect, incidental or consequential damages, losses, injury or costs
of any nature. This warranty is in lieu of and excludes all other warranties, conditions and
guarantees, whether expressed or implied, including without restriction those of
merchantability or tness of use.
Liability under this warranty will not exceed the purchase price for the product claimed to
be defective by the original consumer purchaser. Some states or provinces do not allow
the exclusion or limitation of consequential damages so the above limitations or exclusions
may not apply. This warranty gives you specic legal rights and you may also have other
rights which vary from state to state, or province to province.
Inquiries regarding warranty claims can be directed to [phone], 7:30 a.m. - 4:30 p.m.,
CST, Monday - Friday.
HomewerksWW.com