Homewerks Worldwide AquaVista 26-K82CS-CH-AV User manual

11-26-2019
Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • HomewerksWW.com
KITCHEN FAUCET WITH SIDE SPRAY
26-K82CS-CH-AV – Polished chrome nish
PACKAGE AND HARDWARE CONTENTS
PART DESCRIPTION QUANTITY
C
A
B
A Faucet body 1
B Side spray assembly 1
CMounting nut 2
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water
supply lines.
CAUTION
• If you solder the joints during installation, the seats, cartridges, and washers
must be removed before using a ame or the warranty will be voided on
these parts.
• Cover the drain to avoid losing parts.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package and hardware contents list. If any part is missing or damaged,
do not attempt to assemble the product. Contact customer service for
replacement parts.
Estimated Assembly Time: 30 minutes
Tools required for assembly (not included): adjustable wrenches, groove joint
pliers, pipe wrench, Phillips screwdriver, supply lines, thread seal tape, silicone.
Installation may vary depending on how the previous faucet was installed. Supplies
necessary for the installation of the faucet are not all included; however, they
are available wherever plumbing supplies are sold.
Prior to beginning installation, turn off the hot and cold water lines, then turn
on the old faucet to release built-up pressure. When installing the new faucet,
hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections
that are too tight will reduce the integrity of the system.
Need Help? Please call our toll-free line at [phone] (7:30 am to 4:30 pm CST) for additional assistance or service.

2
PRODUCT SPECIFICATIONS
Max. Flow Rate: 1.8 GPM (6.81 LPM) at 60 PSI Washerless cartridges
ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
NSF 61-9
Polished chrome nish Total weight of item: 2.16 lbs.
ASSEMBLY INSTRUCTIONS
1. Turn off water at the supply valve
under the sink or at the main water
supply. Disconnect the supply lines
to the faucet and remove the old
faucet.
Clean and dry surface area where
new faucet will be mounted.
15. To connect the water supply, use
1/2 in. IPS faucet supply lines (5.1)
or coupling nuts (5.2) with 3/8 in.
O.D. ball-nose risers (5.3). These
parts are not included.
To tighten each faucet connector to
the water supply line, place the rst
wrench on the faucet connector
(5.4) shank to hold it in place while
tightening the supply line (5.1)
tting with a second wrench. This
will prevent the copper tube from
twisting when tightening the faucet
connector. Do not overtighten.
2. Insert the sprayer support (2.1)
through the far right hole on the sink.
Screw the sprayer mounting nut
(2.2) onto the sprayer support (2.1)
shank from underneath the sink, and
hand tighten.
2NOTE: The hot side inlet tube is indicated by a label. When making water
line connections, DO NOT OVERTIGHTEN.
3. Insert the side sprayer (3.1) hose
down through the sprayer support
(3.2) and sink. Align the tabs (3.3
& 3.4) on the quick connects (3.5).
Push the quick connector housing
rmly upward and snap it onto the
receiving tube tab. Pull down moder-
ately to ensure the connection has
been made. If it is necessary to re-
move the quick connector, squeeze
the tabs on the hose, and pull down
to disconnect.
36. After completing the installation,
remove the aerator to rinse the
water pipes. Do not lose the gasket
(6.1) in the aerator. Turn on the
water supply and allow the hot and
cold water to run for at least one
minute at a time. This removes any
residue that may damage the internal
parts. While the water is running,
check for leaks. Turn off the water
and replace the aerator.
6
4.
Place the faucet assembly (4. 1 ) in
position on the sink. Secure the faucet
assembly (4.1) to the sink using the
mounting nuts (4.2) provided. Hand
tighten only.
NOTE: If the sink is uneven, use
silicone under the gasket (4.3).
4
HomewerksWW.com
6
Figure 1
Figure 2
3.4
5.2
5.1
5.
5.4
3
2.1
2.2
3.1
3.2
3.3
3.5
4.3
4.2
4.1
4.3
4.2
4.1
6.1

3
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Faucet leaks underneath handle. Bonnet has come loose or O-ring on cartridge
is dirty or twisted.
1. Move the handle to the OFF position. Unscrew the handle screw and remove
the handle.
2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON
position. The leak should stop draining out from around the cartridge stem.
3. If the leak does not stop, shut off the water supply. Remove the bonnet by
turning it counterclockwise. Lift out the cartridge valve. Inspect the larger
O-ring on the cartridge bonnet and the smaller O-ring on the cartridge stem.
Remove any debris from the O-rings. If either O-ring is twisted, straighten it. If
either O-ring is damaged, replace the cartridge by calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on the
two sides of the cartridge bonnet t into the grooves on the two sides of the
faucet body. Tightly screw the bonnet onto the faucet body.
5. Reinstall the handle.
Water does not completely
shut off.
Rubber valve seat is dirty, stuck, or broken. 1. Shut off the water supply.
2. Remove the handle from the faucet body. Loosen the bonnet by turning it
counterclockwise. Lift out the cartridge assembly.
3. Inspect the rubber valve seat in the faucet body. If there is debris or brass
scrap on the surface of the seat, remove it. If the rubber seat is stuck tightly in the
water inlet hole, push it gently with a ngertip so it moves up and down
smoothly. The spring (smaller end up) must be placed back underneath the valve
seat. If the rubber valve seat is worn out or broken, replace the cartridge by
calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on the two
sides of the cartridge bonnet t into the grooves on the two sides of the faucet
body. Tightly screw the bonnet onto the faucet body.
5. Reinstall the handle.
Faucet leaks around aerator. The aerator is incorrectly tted, dirty, or
small parts inside the aerator are improperly
installed.
1. Remove the aerator from the spout by turning it clockwise. Inspect the black
rubber packing inside the aerator. The rubber packing should be at.
2. Screw the aerator back onto the spout and tighten.
Faucet has an improper water
pattern.
The aerator is dirty or small parts inside the
aerator are improperly installed.
1. Remove the aerator from the spout by turning it clockwise.
2. Gently ush the small parts inside the aerator to clear away any debris.
3. Reinstall the small parts as shown in the replacement parts exploded diagram.
Metal screens must be at and plastic supporter must be straight.
4. Screw the aerator back onto the spout and tighten.
ROUGH-IN
8"
1-1/4" 5-3/4"
10-1/8"
5-7/8"
2" 2-1/8"
4-1/2"
7-1/4"
8-3/4"
1/2"-14NPSM-2A
HomewerksWW.com
CARE AND MAINTENANCE
Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the nish and void your warranty.
OPERATING INSTRUCTIONS
Rotate the handle counterclockwise for cold water. Rotate the handle counterclockwise for hot water. The degree of handle opening determines the volume of water
ow. Returning the handle to the original position stops the ow of water.

4
REPLACEMENT PARTS
For replacement parts, call our customer service department at [phone], 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
PART DESCRIPTION PART #
1Hot index button RP10028
2Cold index button RP10029
3Screw RP50013
4Handle RP13305
5 Bonnet RP70435
6 Washer RP64124
7 Cartridge RP22010
8Washer and screw RP22008
9Mounting nut RP56001
10Cap RP80173CH
11 Washer and o-ring RP70427
12Washer RP64100
13O-ring RP60006
14Aerator assembly RP30260CH
15Washer RP64129
16Diverter RP70007
17Side spray assembly RP36096CH
LIMITED LIFETIME WARRANTY
The distributor warrants to the original consumer purchaser this product to be free from defects
in material and workmanship under normal use in residential applications. At its option, the
Company will provide repair parts or replace defective product when the product is used in
accordance with the manufacturer’s specications.
Use of mild abrasive, abrasive or chemical cleaners may damage the nish of the faucet. We
recommend cleaning your faucet with a soft cloth, moistened with water. Damage resulting
from the use of abrasive or chemical cleaners SHALL VOID THIS WARRANTY.
This warranty is not applicable to any products or parts of products where damage is caused
by use of non-genuine parts; is due to installation error, product misuse, negligence or faulty
maintenance; or where the product is not installed according to local building codes.
This warranty excludes labor charges or damage incurred during installation, repair or
replacement, and any indirect, incidental or consequential damages, losses, injury or costs
of any nature. This warranty is in lieu of and excludes all other warranties, conditions and
guarantees, whether expressed or implied, including without restriction those of
merchantability or tness of use.
Liability under this warranty will not exceed the purchase price for the product claimed to
be defective by the original consumer purchaser. Some states or provinces do not allow
the exclusion or limitation of consequential damages so the above limitations or exclusions
may not apply. This warranty gives you specic legal rights and you may also have other
rights which vary from state to state, or province to province.
Inquiries regarding warranty claims can be directed to [phone], 7:30 a.m. - 4:30 p.m.,
CST, Monday - Friday.
HomewerksWW.com
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
15