Homewerks SmartVent 7145-80V-HS User manual

HomewerksWW.com
SmartVent
BATHROOM
VENTILATION FAN
MODEL 7145-80V-HS
Español p. 13
11-13-2019
Questions, problems, missing parts? Before returning to the store, call our customer
service department at 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
READ AND SAVE THESE INSTRUCTIONS
™

2
HomewerksWW.com
TABLE OF CONTENTS
Product Specications........................................................................................................................2
Package Contents ..............................................................................................................................3
Hardware Included .............................................................................................................................3
Safety Information ..............................................................................................................................4
Preparation.........................................................................................................................................4
New Construction Installation Instructions..........................................................................................6
Existing Construction Installation Instructions ....................................................................................8
Care and Cleaning............................................................................................................................ 11
Troubleshooting................................................................................................................................12
Warranty ...........................................................................................................................................12
PRODUCT SPECIFICATIONS
Airow: 80 - 100 CFM LED light power consumption: 15W
120V, 60Hz LED light brightness: 800 lumens
Duct diameter: 4 in. LED light color (CCT): 4000K Cool White
Sound output: 1.0 - 1.5 sones Night light colors: Blue and Amber
Motor power consumption: 22 - 30.5W Weight: 9.17 lbs.
Exhaust fan speed: 1100 average RPM

3
HomewerksWW.com
HARDWARE INCLUDED (not actual size)
AA BB
Wood Screw
M4 x 30
Machine Screw
M4 x 12
Qty. 8 Qty. 4
PACKAGE CONTENTS
E
C
D
PART DESCRIPTION QTY
A Fan Housing 1
BGrille with LED lights 1
C Suspension Bracket 2
PART DESCRIPTION QTY
D Suspension Bracket 2
E LED Wall Switch 1
A
B

4
HomewerksWW.com
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
• Always disconnect the power supply prior to servicing
the fan, motor or junction box.
• Follow all local building, safety and electrical codes
as well as NEC (National Electrical Code) and OSHA
(Occupational Safety and Health Act).
• Electric Service supply must be 120 volts, 60 hertz.
• This product must properly connect to the grounding
conductor of the supply circuit.
• Do not bend or kink the power wires.
• Do not use this fan with any solid state control device,
such as a remote control, dimmer switch, or certain
timers. Mechanical timers are not solid state devices.
• Do not install in a ceiling with insulation greater than
R40.
• Duct work should be installed in a straight line with
minimal bends.
• Duct work size must be the same size as the discharge
and should not be reduced. Reducing the duct size
may increase fan noise.
WARNING: To reduce the risk of re, electric
shock, or injury to persons, observe the
following:
1. Use this unit in the manner intended by the manufac-
turer. If you have any questions, please call customer
service.
2. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
a qualied person(s) in accordance with all applicable
codes and standards, including re-rated construction.
4. Sufcient air is needed for proper combustion and
exhausting of gases through the ue (chimney) of fuel
burning equipment to prevent backdrafting.Follow the
heating equipment manufacturer´s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE) and local code authorities.
5. When cutting or drilling into the wall or ceiling, do not
damage electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must
be marked as appropriate for the application and be
connected to a GFCI (Ground Fault Circuit Interrupter)-
protected branch circuit.
8. This ventilation fan is intended to be installed at least
3 ft. 3-1/4 in. (1 m) from the showerhead when installing
over a bathtub or shower. Installation within a shower
stall is not recommended for this unit, unless the
3 ft. 3-1/4 in. (1 m) distance can be met.
CAUTION
• For general ventilating use only. Do not
use to exhaust hazardous or explosive
materials and vapors.
• Not for use in cooking areas.
• To reduce the risk of injury to persons,
install the fan at least 7 feet (2.1m) above
the oor.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact
customer service for replacement parts at 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Connectors, Nails, Duct Tape, Phillips Head
Screwdriver, and Utility Knife or Drywall Saw.
Helpful Tools (not included): Electric Drill, Drill Bits
WARNING: RISK OF ELECTRIC SHOCK! Ensure the electricity to the wires you are working on is shut off.
Either remove the fuse or turn off the circuit breaker before removing the existing bath fan or installing
the new one.
Carefully remove unit from carton.

5
HomewerksWW.com
PREPARATION
Before removing your current ventilation unit, verify your switch box on the wall has the required supply wires
necessary for this installation. These supply wires are power/black and neutral/white (refer to right side of wiring
diagram below) at the switch. If you do not see both of these wires, consult a licensed electrician.
Check area above installation location to be sure that wiring can run to the planned location and that duct work can be run
and the area is sufcient for proper ventilation.
Inspect duct work and wiring before proceeding with installation.
Before installation, provide inspection and future maintenance access at a location that will not interfere with installation work.
You may need the help of a second person to install this fan; one person on the attic side and one on the room side.
Note: Installation may vary depending on how the previous bath fan was installed. Supplies necessary for the installation of
your bath fan are not all included; however, most are available at your local home improvement or hardware store.
DIMENSION REQUIREMENTS
Ceiling
Opening (L)
Ceiling
Opening (W)
Ceiling
Opening (H)
Housing
Dimension (L)
Housing
Dimension (W)
Housing
Dimension (H)
9-1/4 in. 9-1/4 in. 8-1/4 in. 9 in. 9 in. 7-13/16 in.
WIRING DIAGRAM
All wiring must be connected for full functionality. Do not use metal wall plate with switch.

6
NEW CONSTRUCTION INSTALLATION INSTRUCTIONS
BEFORE INSTALLATION
WARNING: RISK OF ELECTRIC SHOCK! Ensure the
electricity to the wires you are working on is shut off.
Either remove the fuse or turn off the circuit breaker
before removing the existing bath fan or installing the
new one.
1. Installation Without Suspension Brackets
Place the fan housing (A) next to a ceiling joist or wall stud. The
fan housing (A) should be level and perpendicular to the joist or
wall stud. Allow for thickness of ceiling board or drywall used
in your application. DO NOT ush mount to joist or wall stud.
Bottom of fan housing (A) should be ush with the ceiling board
or drywall.
12
A
1
2. Mount fan housing (A) to the joist or wall stud using wood
screws (AA) where indicated by arrows outside the fan
body (A).
A
Hardware Used
AA Wood screws x 2
2
A
AA
AA
A
3. Installation With Suspension Brackets
Insert suspension brackets (C and D) onto fan housing (A).
Position the fan housing (A) so the edge of fan is ush with the
ceiling board or drywall. Do not ush mount the fan housing (A)
with the ceiling joist or wall stud.
3
4. Secure the fan housing (A) to the ceiling joists or wall studs
using wood screws (AA) (included).
Hardware Used
AA Wood screws x 8
4
AA
A
HomewerksWW.com

7
HomewerksWW.com
NEW CONSTRUCTION INSTALLATION INSTRUCTIONS (continued)
5. Secure the suspension brackets (C and D) to the fan housing (A)
using machine screws (BB) (included).
Hardware Used
BB Machine screws x 4
BB
BB
D
C
A
5
6. Remove the wiring cover. Pull the house wires through the
wiring cover hole. Using the attached quick connectors, connect
120v house wiring to the fan as shown in the wiring diagram
on page 5. 12-18 AWG is the smallest conductor that should
be used for branch circuit wiring.
Carefully push the connected wires back into the wiring box
housing. Reattach the wiring box cover.
CAUTION: If the house electrical wires do not match the
colors from the fan wiring diagram on page 5, you must
determine what each house wire represents before
connecting. You may need to consult an electrical
contractor to determine safely.
Wire
cover
Wire
cover
House
wire
Product
wire Quick
connect
6
7. Connect a 4 in. circular duct (not included) and vent to the
outside. Secure it with duct tape (not included) or a clamp
(not included) to make the connection secure and airtight.
Finish ceiling work. Ceiling hole should be aligned with edge
of the fan housing (A).
7
A
8. Plug the connector attached to the grille (B) into the
connector on the fan housing (A). 8
A
B
Connector

8
HomewerksWW.com
NEW CONSTRUCTION INSTALLATION INSTRUCTIONS (continued)
9. Attach the grille (B) by pinching the mounting springs
and inserting into the narrow rectangular slots in the
fan housing (A).
Turn on the power source. If you hear any abnormal sound
or vibration, please refer to the Troubleshooting Guide on
page 12.
9
A
B
Mounting
spring
EXISTING CONSTRUCTION INSTALLATION INSTRUCTIONS
BEFORE INSTALLATION
WARNING: RISK OF ELECTRIC SHOCK! Ensure the
electricity to the wires you are working on is shut off.
Either remove the fuse or turn off the circuit breaker
before removing the existing bath fan or installing the
new one.
1. Remove existing fan. 1
2. Measure the opening to ensure it is large enough to accommo-
date the new fan housing (9-1/4 in. x 9-1/4 in.). 2
45678910111
3. If the opening is not large enough for the new fan housing,
cut a 9-1/4 in. x 9-1/4 in. opening for the fan housing (A). 3
9-1/4"
9-1⁄4 "

9
HomewerksWW.com
EXISTING CONSTRUCTION INSTALLATION INSTRUCTIONS (continued)
4. Installation Without Suspension Brackets
Place the fan housing (A) next to a ceiling joist or wall stud. The
fan housing (A) should be level and perpendicular to the joist or
wall stud. Allow for thickness of ceiling board or drywall used
in your application. DO NOT ush mount to joist or wall stud.
Bottom of fan housing (A) should be ush with the ceiling board
or drywall.
12
A
4
5. Mount fan housing (A) to the joist or wall stud using wood
screws (AA) where indicated by arrows outside the fan
body (A).
A
Hardware Used
AA Wood screws x 2
5
A
AA
AA
A
6. Installation With Suspension Brackets
Insert suspension brackets (C and D) onto the fan housing
(A). Position the fan housing (A) so the edge of fan is ush
with the ceiling board or drywall. Do not ush mount the fan
housing (A) with the ceiling joist or wall stud.
6
7. Secure the fan housing (A) to the ceiling joists or wall studs
using wood screws (AA) (included).
Hardware Used
AA Wood screws x 8
7
AA
A
8. Secure the suspension brackets (C and D) to the fan housing (A)
using machine screws (BB) (included).
Hardware Used
BB Machine screws x 4
BB
BB
D
C
A
8

10
HomewerksWW.com
EXISTING CONSTRUCTION INSTALLATION INSTRUCTIONS (continued)
9. Remove the wiring cover. Pull the house wires through the
wiring cover hole. Using the attached quick connectors, connect
120v house wiring to the fan as shown in the wiring diagram
on page 5. 12-18 AWG is the smallest conductor that should
be used for branch circuit wiring.
Carefully push the connected wires back into the wiring box
housing. Reattach the wiring box cover.
CAUTION: If the house electrical wires do not match the
colors from the fan wiring diagram on page 5, you must
determine what each house wire represents before
connecting. You may need to consult an electrical
contractor to determine safely.
Wire
cover
Wire
cover
House
wire
Product
wire Quick
connect
9
10. Connect a 4 in. circular duct (not included) and vent to the
outside. Secure it with duct tape (not included) or a clamp
(not included) to make the connection secure and airtight.
Finish ceiling work. Ceiling hole should be aligned with edge
of the fan housing (A).
10
A
11. Plug the connector attached to the grille (B) into the
connector on the fan housing (A). 11
A
B
Connector
12. Attach the grille (B) by pinching the mounting springs
and inserting into the narrow rectangular slots in the
fan housing (A).
Turn on the power source. If you hear any abnormal sound
or vibration, please refer to the Troubleshooting Guide on
page 12.
12
A
B
Mounting
spring

11
HomewerksWW.com
CARE AND CLEANING
CAUTION: Before attempting to clean the xture, disconnect the power to the xture by turning the breaker
off or removing the fuse from the fuse box.
• See safety information before proceeding. Routine maintenance should be done at least once a year.
• Never use solvents, thinner or harsh chemicals for cleaning the fan.
• Do not allow water to enter the motor.
• Do not immerse metal parts in water.
• Do not immerse resin parts in water more than 140°F.
1. Remove grille (B) by squeezing springs and pulling down. Wipe
grille with a damp cloth.
B
1
2. Remove dust and dirt from the fan housing (A) with a vacuum
cleaner.
A
2
3. Wipe the fan housing (A) with a damp cloth and wipe dry.
A
3
4. Replace the grille (B) and turn on the power source.
A
B
4

12
HomewerksWW.com
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
The fan seems louder than it
should. The CFM is too great. Be sure the CFM rating on the fan matches the square footage of your room.
The damper is damaged or not working properly. Check the damper to ensure it is opening and closing
properly. If the damper has become damaged, please
call Customer Service.
The bend in the duct is too close to the fan dis-
charge.
Be sure you do not have any sharp bends in the duct
within 18 in. of the fan discharge.
The fan discharge is reduced to t a smaller duct. Use the recommended size ducting to reduce fan
noise.
The fan body is not attached securely. Be sure the fan is securely attached to the ceiling
joists.
The fan has an abnormal
sound or vibration. Fan body is not attached securely. Be sure the fan housing is securely attached to the ceiling joists or wall studs.
The grille is not attached securely. Be sure the grille is pushed upward until it is gently,
but rmly attached to the fan housing.
The circular duct is not secured to the duct
connector. Be sure the duct tape or clamp is secured for an airtight connection.
The fan is not clearing
humidity from the room. There is insufcient airow intake in the room. Be sure a door or window is slightly ajar or open to allow airow. The fan is not able to draw air out of the
room without enough airow.
There is insufcient CFM.
NOTE: Using a tissue is not the correct method for
determining if the fan is operating properly. If the fan
clears steam from the room within approximately 15
minutes of completing your shower, then the fan is
operating properly.
Be sure the CFM rating of the fan matches the
square footage of your room.
The fan keeps running even
though the humidity level is
lower than 60% RH.
NOTE: Our sensor tolerance
is +/-10% RH.
Outdoor humidity is back drafting into the fan. Continue to let fan run since it is good to keep venting
the house and the electric cost is minimal (estimated
at less than $10 per year).
If the light on the grille is red, the fan is in full speed
mode and not humidity sensing mode and will not
shut off automatically.
Turn the fan off when not in use.
LIMITED 3-YEAR WARRANTY
If the fan fails due to a defect in materials or workmanship at any time during the rst three (3) years of ownership, the manufacturer will
replace it free of charge, postage-paid at their option. This warranty does not cover products that have been abused, altered, damaged,
misused, cut or worn. This warranty does not cover use in commercial applications. Use only manufacturer-supplied genuine warranty
repair replacement parts to repair this fan. Use of non-genuine repair parts will void your warranty. The manufacturer DISCLAIMS all
other implied or express warranties including all warranties of merchantability and/or tness for a particular purpose. As some states do
not allow exclusions or limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives
you specic legal rights, and you may have other rights that vary from state to state.
This warranty is limited to the replacement of defective parts only. Labor charges and/or damage incurred during installation, repair,
replacement as well as incidental and consequential damages connected with the above are excluded. Any damage to this product
as a result of neglect, misuse, accident, improper installation or use other than the purpose SHALL VOID THIS WARRANTY.
Shipping costs for return product as part of a claim on the warranty must be paid for by the customer. Inquiries regarding warranty
claims can be directed to 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
The device has been evaluated to meet general RF exposure requirement,
The device can be used in portable exposure condition without restriction
Federal Communication Commission (FCC) Radiation Exposure Statement
Power is so low that no RF exposure calculation is needed.
FCC statements:
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to
this equipment. Such modifications or changes could void the user’s authority to operate the equipment.