homgeek NY-8608MC User manual
Model: NY- 8608MC
High Speed Blender
Instruction Manual
AC120V, 50/60Hz, 1450W
[ IMPORTANT ]
Please feel free to check out our website
www.homgeek.com
for more information.
Most customer has useful discover there,
you probably will, too.
Important Safeguards
Parts and Features
Control Panel
Operational Area Features
Use Your Blender
Using Variable Speed Dial
FAQ
Cleaning & Maintenance
Troubleshooting
Warranty & Service
[ CONTENT ]
- 01 -
2
5
6
7
8
11
11
12
14
14
IMPORTANT SAFEGUARDS
WARNING: This unit contains electrical connections and moving parts that potentially present risk to the
user. To avoid the risk of serious injury when using your blender. basic safety precautions should be
followed, including but not limited to following:
READ ALL INSTRUCTIONS, SAFEGUARDS, AND WARNINGS BEFORE OPERATING BLENDER.
The failure to follow any of the important safeguards and instructions for safe use is a misuse of your
blender, which can create the risk of serious injure and void your warranty.
1. Read all instructions.
2. Carefully observe and follow all warnings and instructions.
3. Take your time and exercise care during unpacking and appliance setup. This appliance contains sharp
blades that can cause injury if mishandled.
4. Take inventory of all contents to ensure that you have all parts needed to properly and safely operate
your appliance.
5. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or
mental capabilities, or lack of experience and knowledge, unless they are closed supervised and
instructed concerning use of the appliance by a person responsible for their safety. Close supervision is
necessary when any appliance is used by or near children. Children should be supervised to ensure that
they do not play with the appliance.
6. Do not allow children to operate this appliance or use as a toy. Close supervision is necessary when
any appliance is used near children.
7. To protect against the risk of electric shock, DO NOT submerge the appliance or allow the power cord
to contact any form of liquid.
8. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassem-
bling parts and before cleaning. To unplug, grasp the plug and pull from the out let. Never pull from the
power cord.
9. To avoid a hazard due to inadvertent resetting of the thermal cut-out, power to this blender must not be
supplied through an external switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
10. Do not operate any blender with a damaged cord or plug or after the blender malfunctions, or is
tion, repair, or adjustment.
11. GFI circuit breakers might be installed in your kitchen. Look for them in outlets near sinks. If the
blender won’t operate, unplug the blender. Reset the wall outlet or circuit breaker. If the circuit breaker
continues to trip, unplug the blender from the outlet. Allow the blender to sit for 24 hours before attempting
to use it again. Contact Customer Service if the problem persists.
12. This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric
shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. DO NOT modify the plug in any way.
13. This appliance has important information on the plug prong. The power cord is not suitable for
replacement. If damaged, contact homgeek for servicing in order to avoid a hazard.
14. Before use, wash all parts that may come into contact with food. Follow washing instructions covered
in this instruction manual.
15. ALWAYS use the appliance on a dry and level and firm surface. Never operate the appliance on soft
surfaces.
16. Avoid touching moving parts.
17. Alteration or modification of any part of the blender base or container, including the use of any part or
parts that are not genuine authorized homgeek parts, may cause fire, electric shock, or injury.
18. The use of attachments, including canning jars, not expressly authorized or sold by homgeek for use
with this blender, including container, may cause fire, electric shock, or injury.
19. Do not use outdoors.
20. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use blender for other than
intended use.
21. Check if the voltage you are using matches the voltage listed on the machine.
22. Do not let cord hang over edge of table or counter.
23. Do not let cord come into contact with hot surface, including the stove.
24. DO NOT operate this appliance on or near any hot surfaces (such as gas or electric burner or in a
heated oven). Never leave an appliance unattended when in use.
25. Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons
or damage to the blender. A scraper may be used but must be used only when the blender is not running.
26. The tamper provided must be used only when the main part of the lid is in place.
27. Do not leave foreign objects, such as spoons, forks, knives or the lid plug, in the container as this will
damage the blades and other components when starting the machine and may cause injury.
28. Never attempt to operate with damaged blades.
29. DO NOT use the appliance if blade assembly is bent or damaged.
30. Before each use, inspect blades for damage. If blades are bent or damage is suspected, contact
homgeek to arrange for replacement.
31. Always operate blender with lid and lid plug firmly in place. The lid plug should be removed only when
adding ingredients and when using the tamper.
32. If you find unmixed ingredients sticking to the sides of the container, stop the appliance, remove the
lid, and use a spatula to dislodge ingredients. NEVER insert your hands into the container, as you may
contact one of the blades and experience a laceration.
33. DO NOT attempt to remove the container and lids from the motor base while the blades are still
spinning. Allow the appliance to come to a complete stop before removing lids and containers.
34. Add ingredients to the container. NOTE: Do not overfill! To avoid spilling, do not add ingredients past
the “MAX” fill line.
35. When blending hot liquids or ingredients, use caution; spray or escaping steam may cause scalding
and burns. Do not fill container over half full of the capacity. Always begin processing on the lowest speed
setting, variable speed 0 and slowly increase speed. Keep hands and other exposed skin away from the
lid opening to prevent possible burns.
36. When making nut butters or oil-based foods, do not process for more than one minute after the mixture
starts to circulate in the container. Processing for longer periods can cause dangerous overheating.
37. Machines and power cords should be stored in a safe place to prevent children from pulling on the
power cord.
38. Blades are sharp-handle with care. Clean around the blades in the container with extreme care to
avoid injury.
39. Never attempt to operate with the centering pad removed.
40. Make sure that the container and blades base are flush with the centering pad to ensure that the drive
spline is engaged with the drive socket before operating.
41. DO NOT attempt to Defeat the interlock mechanism.
42. DO NOT use your container to heat ingredients.
43. DO NOT continuously use your machine for more than 5 minutes.
44. DO NOT attempt to sharpen blades.
45. DO NOT expose container to extreme temperature changes.
46. Appliance accessories are not intended to be used in the microwave. Do not place the container or the
lid in the microwave as it may result in damage to the accessories.
47. Extension cords are not recommended for use with this product.
48. If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset,
unplug the appliance and allow it to cool for approximately 1 hour before using again.
49. DO NOT store ingredients before or after blending them in the container with the blades attached.
Some foods may contain active ingredients or release gases that will expand if left in a sealed container,
resulting in excessive pressure buildup that can pose a risk of injury.
50. Never handle the plug with wet hands.
51. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control
to “off”, then remove plug from wall outlet.
52. Flashing light indicates ready to operate. Avoid any contact with blades or moveable parts.
53. Save this manual for future reference.
SAVE THESE INSTRUCTIONS
Household use only
- 02 -
IMPORTANT SAFEGUARDS
WARNING: This unit contains electrical connections and moving parts that potentially present risk to the
user. To avoid the risk of serious injury when using your blender. basic safety precautions should be
followed, including but not limited to following:
READ ALL INSTRUCTIONS, SAFEGUARDS, AND WARNINGS BEFORE OPERATING BLENDER.
The failure to follow any of the important safeguards and instructions for safe use is a misuse of your
blender, which can create the risk of serious injure and void your warranty.
1. Read all instructions.
2. Carefully observe and follow all warnings and instructions.
3. Take your time and exercise care during unpacking and appliance setup. This appliance contains sharp
blades that can cause injury if mishandled.
4. Take inventory of all contents to ensure that you have all parts needed to properly and safely operate
your appliance.
5. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or
mental capabilities, or lack of experience and knowledge, unless they are closed supervised and
instructed concerning use of the appliance by a person responsible for their safety. Close supervision is
necessary when any appliance is used by or near children. Children should be supervised to ensure that
they do not play with the appliance.
6. Do not allow children to operate this appliance or use as a toy. Close supervision is necessary when
any appliance is used near children.
7. To protect against the risk of electric shock, DO NOT submerge the appliance or allow the power cord
to contact any form of liquid.
8. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassem-
bling parts and before cleaning. To unplug, grasp the plug and pull from the out let. Never pull from the
power cord.
9. To avoid a hazard due to inadvertent resetting of the thermal cut-out, power to this blender must not be
supplied through an external switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
10. Do not operate any blender with a damaged cord or plug or after the blender malfunctions, or is
tion, repair, or adjustment.
11. GFI circuit breakers might be installed in your kitchen. Look for them in outlets near sinks. If the
blender won’t operate, unplug the blender. Reset the wall outlet or circuit breaker. If the circuit breaker
continues to trip, unplug the blender from the outlet. Allow the blender to sit for 24 hours before attempting
to use it again. Contact Customer Service if the problem persists.
12. This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric
shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. DO NOT modify the plug in any way.
13. This appliance has important information on the plug prong. The power cord is not suitable for
replacement. If damaged, contact homgeek for servicing in order to avoid a hazard.
14. Before use, wash all parts that may come into contact with food. Follow washing instructions covered
in this instruction manual.
15. ALWAYS use the appliance on a dry and level and firm surface. Never operate the appliance on soft
surfaces.
16. Avoid touching moving parts.
17. Alteration or modification of any part of the blender base or container, including the use of any part or
parts that are not genuine authorized homgeek parts, may cause fire, electric shock, or injury.
18. The use of attachments, including canning jars, not expressly authorized or sold by homgeek for use
with this blender, including container, may cause fire, electric shock, or injury.
19. Do not use outdoors.
20. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use blender for other than
intended use.
21. Check if the voltage you are using matches the voltage listed on the machine.
22. Do not let cord hang over edge of table or counter.
23. Do not let cord come into contact with hot surface, including the stove.
24. DO NOT operate this appliance on or near any hot surfaces (such as gas or electric burner or in a
heated oven). Never leave an appliance unattended when in use.
25. Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons
or damage to the blender. A scraper may be used but must be used only when the blender is not running.
26. The tamper provided must be used only when the main part of the lid is in place.
27. Do not leave foreign objects, such as spoons, forks, knives or the lid plug, in the container as this will
damage the blades and other components when starting the machine and may cause injury.
28. Never attempt to operate with damaged blades.
29. DO NOT use the appliance if blade assembly is bent or damaged.
30. Before each use, inspect blades for damage. If blades are bent or damage is suspected, contact
homgeek to arrange for replacement.
31. Always operate blender with lid and lid plug firmly in place. The lid plug should be removed only when
adding ingredients and when using the tamper.
32. If you find unmixed ingredients sticking to the sides of the container, stop the appliance, remove the
lid, and use a spatula to dislodge ingredients. NEVER insert your hands into the container, as you may
contact one of the blades and experience a laceration.
33. DO NOT attempt to remove the container and lids from the motor base while the blades are still
spinning. Allow the appliance to come to a complete stop before removing lids and containers.
34. Add ingredients to the container. NOTE: Do not overfill! To avoid spilling, do not add ingredients past
the “MAX” fill line.
35. When blending hot liquids or ingredients, use caution; spray or escaping steam may cause scalding
and burns. Do not fill container over half full of the capacity. Always begin processing on the lowest speed
setting, variable speed 0 and slowly increase speed. Keep hands and other exposed skin away from the
lid opening to prevent possible burns.
36. When making nut butters or oil-based foods, do not process for more than one minute after the mixture
starts to circulate in the container. Processing for longer periods can cause dangerous overheating.
37. Machines and power cords should be stored in a safe place to prevent children from pulling on the
power cord.
38. Blades are sharp-handle with care. Clean around the blades in the container with extreme care to
avoid injury.
39. Never attempt to operate with the centering pad removed.
40. Make sure that the container and blades base are flush with the centering pad to ensure that the drive
spline is engaged with the drive socket before operating.
41. DO NOT attempt to Defeat the interlock mechanism.
42. DO NOT use your container to heat ingredients.
43. DO NOT continuously use your machine for more than 5 minutes.
44. DO NOT attempt to sharpen blades.
45. DO NOT expose container to extreme temperature changes.
46. Appliance accessories are not intended to be used in the microwave. Do not place the container or the
lid in the microwave as it may result in damage to the accessories.
47. Extension cords are not recommended for use with this product.
48. If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset,
unplug the appliance and allow it to cool for approximately 1 hour before using again.
49. DO NOT store ingredients before or after blending them in the container with the blades attached.
Some foods may contain active ingredients or release gases that will expand if left in a sealed container,
resulting in excessive pressure buildup that can pose a risk of injury.
50. Never handle the plug with wet hands.
51. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control
to “off”, then remove plug from wall outlet.
52. Flashing light indicates ready to operate. Avoid any contact with blades or moveable parts.
53. Save this manual for future reference.
SAVE THESE INSTRUCTIONS
Household use only
- 03 -
IMPORTANT SAFEGUARDS
WARNING: This unit contains electrical connections and moving parts that potentially present risk to the
user. To avoid the risk of serious injury when using your blender. basic safety precautions should be
followed, including but not limited to following:
READ ALL INSTRUCTIONS, SAFEGUARDS, AND WARNINGS BEFORE OPERATING BLENDER.
The failure to follow any of the important safeguards and instructions for safe use is a misuse of your
blender, which can create the risk of serious injure and void your warranty.
1. Read all instructions.
2. Carefully observe and follow all warnings and instructions.
3. Take your time and exercise care during unpacking and appliance setup. This appliance contains sharp
blades that can cause injury if mishandled.
4. Take inventory of all contents to ensure that you have all parts needed to properly and safely operate
your appliance.
5. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or
mental capabilities, or lack of experience and knowledge, unless they are closed supervised and
instructed concerning use of the appliance by a person responsible for their safety. Close supervision is
necessary when any appliance is used by or near children. Children should be supervised to ensure that
they do not play with the appliance.
6. Do not allow children to operate this appliance or use as a toy. Close supervision is necessary when
any appliance is used near children.
7. To protect against the risk of electric shock, DO NOT submerge the appliance or allow the power cord
to contact any form of liquid.
8. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassem-
bling parts and before cleaning. To unplug, grasp the plug and pull from the out let. Never pull from the
power cord.
9. To avoid a hazard due to inadvertent resetting of the thermal cut-out, power to this blender must not be
supplied through an external switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
10. Do not operate any blender with a damaged cord or plug or after the blender malfunctions, or is
tion, repair, or adjustment.
11. GFI circuit breakers might be installed in your kitchen. Look for them in outlets near sinks. If the
blender won’t operate, unplug the blender. Reset the wall outlet or circuit breaker. If the circuit breaker
continues to trip, unplug the blender from the outlet. Allow the blender to sit for 24 hours before attempting
to use it again. Contact Customer Service if the problem persists.
12. This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric
shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. DO NOT modify the plug in any way.
13. This appliance has important information on the plug prong. The power cord is not suitable for
replacement. If damaged, contact homgeek for servicing in order to avoid a hazard.
14. Before use, wash all parts that may come into contact with food. Follow washing instructions covered
in this instruction manual.
15. ALWAYS use the appliance on a dry and level and firm surface. Never operate the appliance on soft
surfaces.
16. Avoid touching moving parts.
17. Alteration or modification of any part of the blender base or container, including the use of any part or
parts that are not genuine authorized homgeek parts, may cause fire, electric shock, or injury.
18. The use of attachments, including canning jars, not expressly authorized or sold by homgeek for use
with this blender, including container, may cause fire, electric shock, or injury.
19. Do not use outdoors.
20. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use blender for other than
intended use.
21. Check if the voltage you are using matches the voltage listed on the machine.
22. Do not let cord hang over edge of table or counter.
23. Do not let cord come into contact with hot surface, including the stove.
24. DO NOT operate this appliance on or near any hot surfaces (such as gas or electric burner or in a
heated oven). Never leave an appliance unattended when in use.
25. Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons
or damage to the blender. A scraper may be used but must be used only when the blender is not running.
26. The tamper provided must be used only when the main part of the lid is in place.
27. Do not leave foreign objects, such as spoons, forks, knives or the lid plug, in the container as this will
damage the blades and other components when starting the machine and may cause injury.
28. Never attempt to operate with damaged blades.
29. DO NOT use the appliance if blade assembly is bent or damaged.
30. Before each use, inspect blades for damage. If blades are bent or damage is suspected, contact
homgeek to arrange for replacement.
31. Always operate blender with lid and lid plug firmly in place. The lid plug should be removed only when
adding ingredients and when using the tamper.
32. If you find unmixed ingredients sticking to the sides of the container, stop the appliance, remove the
lid, and use a spatula to dislodge ingredients. NEVER insert your hands into the container, as you may
contact one of the blades and experience a laceration.
33. DO NOT attempt to remove the container and lids from the motor base while the blades are still
spinning. Allow the appliance to come to a complete stop before removing lids and containers.
34. Add ingredients to the container. NOTE: Do not overfill! To avoid spilling, do not add ingredients past
the “MAX” fill line.
35. When blending hot liquids or ingredients, use caution; spray or escaping steam may cause scalding
and burns. Do not fill container over half full of the capacity. Always begin processing on the lowest speed
setting, variable speed 0 and slowly increase speed. Keep hands and other exposed skin away from the
lid opening to prevent possible burns.
36. When making nut butters or oil-based foods, do not process for more than one minute after the mixture
starts to circulate in the container. Processing for longer periods can cause dangerous overheating.
37. Machines and power cords should be stored in a safe place to prevent children from pulling on the
power cord.
38. Blades are sharp-handle with care. Clean around the blades in the container with extreme care to
avoid injury.
39. Never attempt to operate with the centering pad removed.
40. Make sure that the container and blades base are flush with the centering pad to ensure that the drive
spline is engaged with the drive socket before operating.
41. DO NOT attempt to Defeat the interlock mechanism.
42. DO NOT use your container to heat ingredients.
43. DO NOT continuously use your machine for more than 5 minutes.
44. DO NOT attempt to sharpen blades.
45. DO NOT expose container to extreme temperature changes.
46. Appliance accessories are not intended to be used in the microwave. Do not place the container or the
lid in the microwave as it may result in damage to the accessories.
47. Extension cords are not recommended for use with this product.
48. If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset,
unplug the appliance and allow it to cool for approximately 1 hour before using again.
49. DO NOT store ingredients before or after blending them in the container with the blades attached.
Some foods may contain active ingredients or release gases that will expand if left in a sealed container,
resulting in excessive pressure buildup that can pose a risk of injury.
50. Never handle the plug with wet hands.
51. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control
to “off”, then remove plug from wall outlet.
52. Flashing light indicates ready to operate. Avoid any contact with blades or moveable parts.
53. Save this manual for future reference.
SAVE THESE INSTRUCTIONS
Household use only
WARNING
Before using the product,
please read the manual and all
explanations carefully.
Please don’t use the product
beyond its functions.
The voltage to use should
be 120V.
Please don’t let children use
the product.
Please stop using the product
when power line or plug damage
or other functions failure.
The product must be operated
on stable reliable worktable.
Please don’t let power line touch
sharp edge or high temperature
surface.
Hold the plug tightly when pulling
it, don’t pull its line.
The product is household use
only.
Don’t put the product into water
or any other liquids
To ensure safety, please don’t disassemble the product privately. If there is abnormal
situation, please contact customer service which contact information is printed on the
manual. It must be repaired by manufacturer or special technician of after-sale service
center appointed by manufacturer.
- 04 -
PARTS & FEATURES
Specifications
Product
Model Voltage Frequency Power Capacity Max. Speed
NY-8608MC AC120V 50Hz/60Hz 1450W 2.0L 30000RPM
- 05 -
Lid Plug
Tamper
2-Part Lid
2.0L Container
Blades
Centering Pad
Control Panel
Motor Base
Slip Resistant
Feet
Slip Resistant
Feet
Power Cord
2-Part Lid:The 2-part Lid is easy to put on and take off and easy to clean.
Always use the complete 2-part lid when blending, especially when blending hot ingredients (unless the
tamper is inserted through the lid plug opening). Never operate the blender without the lid securely
latched during operation.
Lid Plug: Insert through the lid plug opening and secure by turning clockwise. Turn counterclockwise and
lift it to remove the lid plug for using the tamper or adding ingredients.
Container: Ounces/milliliters/cups are clearly marked.
Blades: Blades are made of ultra-sharp stainless steel. The container is designed to be completely
cleanable without removing retainer nut and blades. DO NOT attempt to remove the retainer nut or blades
from the container.
Centering Pad: The container must be aligned over the centering pad. Never attempt to operate with the
centering pad removed.
Motor Base: The motor is designed with dual protection circuits to prevent overheating and an overload.
Tamper: Used to process thicker mixtures and keep ingredients moving towards and through the blades.
CAUTION 1: The tamper can only be used only when the main part of the lid is in place. Hold the
container while using the tamper.
CAUTION 2: Lids and tampers are not interchangeable between different container styles, types, and sizes.
Power Cord: The blender is equipped with a long power cord. Store the unused portion neatly underneath.
Bottom View/Cord Wrap: Plastic cord retainers hold the cord securely. They are flexible and return to
position after the cord is lifted out.
Slip Resistant Feet: Prevent movement during use and prevent damaging marks on countertops or tables.
b. High/Variable Switch
High: The highest speed available
Variable: Activates the Variable Speed Dial
c. Variable Speed Dial
Manual control of lower speed from Variable 0 (stop) to 10
a. On/off key
Controls power to the machine
CONTROL PANEL
- 06 -
bca
a. On/Off key: This key controls power to the machine. Push up to turn on the machine. Push down to
turn off.
b. High/Variable Switch:
High: The High function can be used when a smart program is selected and when you are using Variable
Speed Dial. Pushing the High/Variable Switch up to High position will cause the machine to blend at the
highest speed available. High provides the best quality of refinement, breaking down ice, frozen fruit,
whole fruits or vegetables, and grains to a smooth- lump-free consistency.
WARNING: Do not begin processing directly on the High setting.
Always make sure that the High/Variable Switch is set to Variable before pushing the On/Off Switch to
the On position.
Variable: Switch to Variable to activate all of the lower variable speeds by using Variable Speed Dial.
c. Variable Speed Dial: Gives you manual control of lower speed from Variable 0 (stop) to 8. It is active
only when the High/Variable Switch is set in the Variable position. LCD Display Screen displays speed
number in orange color when turning Dial. Timer will count up and elapsed time in white color will be
displayed on LCD screen.
Warning: Always make sure that the marker on Variable Speed Dial is set to 0before pushing the On/Off
Switch to the On position.
Variable Speed Dial (manual) Features
Program Speed Working
Time
Is Time
Adjustable? Time Range Auto
start after Used for
DIAL 0-10
Time elapses
when using
Variable Speed
Dial
Elapsed time 0 second
Making
whole-food
juices soups,
shakes, frozen
mixtures,
purees, nut
butters, and for
grinding grains.
0 seconds
OPERATING INSTRUCTIONS
IMPORTANT: READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY BEFORE USE. THE
FAILURE TO FOLLOW ANY OF THE IMPORTANT SAFEGUARDS AND IMPORTANT SAFETY
INSTRUCTIONS FOR SAFE USE IS A MISUSE OF YOUR BLENDER THAT CAN VOID YOUR
WARRANTY AND CREATE THE RISK OF SERIOUS INJURY.
BEFORE FIRST USE
1. Remove all packaging materials and labels from the appliance.
WARNING: Blades are sharp. Use extreme caution when handling.
2. Container, lids, and tamper are not dishwasher safe. If preferred, wash all parts in warm soapy water.
Rinse clean under running water and dry thoroughly. Wipe the motor base with a warm, damp cloth and
wipe clean with a dry, soft cloth. Allow all parts to dry completely before using.
WARNING: Do not place the motor base in water or other liquids. Do not let any liquid enter the
motor.
OPERATIONAL AREAS FEATURES
- 07 -
IMPORTANT: This unit contains electrical connections and moving parts that potentially present a risk to
the user. Read all important safeguards and instructions before operating the blender.
1. Place motor base on a clean, dry, even, level and firm surface such as a countertop or table.
2. Make sure the centering pad is securely aligned over the motor base before using.
3. Cut food into smaller pieces for more efficient blending. Add ingredients to the container, making sure
not to exceed the “MAX” fill line.
WARNING:
DON’T fill container with Hot ingredients over half full capacity to avoid overflow and cause injury.
NOTE: If you need to add additional ingredients while the appliance is processing, open the lid plug and
pour ingredients in through the lid plug opening. Make sure the main part of the lid is in place when
adding ingredients.
IMPORTANT: NEVER RUN THE APPLIANCE EMPTY.
WARNING
Electrical Shock Hazard
Use grounded outlet only.
DO NOT use an adapter.
DO NOT use an extension cord.
DO NOT remove ground.
Always unplug before cleaning or when not in use. Do not put the
motor base in water or any other liquids or let any form of liquid
enter the motor.
Failure to follow instructions in manual can cause death or
electrical shock.
USE YOUR BLENDER
Centering Pad
Motor Base
- 08 -
4. With the motor off, set the container on the motor base by aligning it over the centering pad. The
container can be installed in four different orientations. The handle can be aligned on either of the 4 sides
of the motor base. Do not ever attempt to put a container on an operating motor base or to operate a
motor base without a container properly in place. The motor will not work if the container is not installed
correctly.
CAUTION: Never attempt to remove the container while the appliance is still running.
5. Push the lid down into container firmly with lid flaps midway between the spout and the handle. Make
sure that both side clips on lid fully snap onto lip of container. Insert the lid plug into the lid plug opening
and turn clockwise to lock in place.
CAUTION: Never operate the blender without the lid securely latched during operation. Always use the
complete 2-part lid when blending, especially when blending hot ingredients (unless the tamper is inserted
through the lid plug opening).
Tips: How to load your container
according to your recipe?
We suggest, liquids first, then
dry goods, leafy greens, fruit &
veggies and finally ice & frozen
ingredients.
Ice & Frozen Ingredients
Fruit & Veggies
Leafy Greens
Dry Goods
Liquids
- 09 -
6. Check up the Variable Speed Dial. Make sure the High/Variable Switch is switched to Variable
position and the marker on Variable Speed Dial is pointing to “0” before powering on. When the
unit is connected to power and the container is correctly put onto the motor base, the unit will work at
once under the set speed that the marker on Variable Speed Dial is pointing if the marker on Variable
Speed Dial is not at “0”.
7. Plug the blender into a grounded, 2-prong outlet. On will be displayed on the LCD Display Screen
indicating that the appliance is ready for use.
Warning: Make sure the power plug is safely connected to a grounded wall electrical socket.
Warning: After plugged in, NEVER insert your hands into the container, as you may contact one of
the blades and experience a laceration.
8. Start to blend either using, Variable Speed Dial, or simply pressing a smart program button.
IMPORTANT! Never start on speeds above 0 with hot liquids to avoid possible burns. Always start
on Variable 0 and slowly increase speed. Escaping steam, or splashes from contents may scald.
Lock the lid and lid plug securely in place before operating the machine.
Power Supply
120V AC
- 10 -
1. Make sure the marker on Variable Speed dial is at “0” position.
2. Push the On/Off Switch up to On position, then slowly increase to the desired speed between 1 and
10during the blending cycle.
3. During blending, you can push the High/Variable Switch up to High position for the highest speed of
blending and turn it back to Variable position for using Variable Speed Dial again.
4. To stop blending, turn the marker on Variable Speed Dial to “0” and blender will enter standby mode.
Push the On/Off Switch down to Off and blender will power off.
Note:
Make sure that the marker on Variable Speed Dial is pointed to “0” after each use.
* If ingredients are not blending properly, use a tamper to help push ingredients towards blades. If this
does not work, press On/Off to Off position to power off. Remove the container from the blender base
and use a rubber spatula to press the air bubble away from the blades. Add liquid if necessary. Replace
the lid and lid plug. Replace container to the motor base and continue blending.
9. When blending is complete, turn off and unplug the appliance. Wait for the blades to completely stop
spinning.
CAUTION: Make sure that the motor base is unplugged when not in use.
10. To remove the container from motor base, lift it off the motor base.
WARNING: Be sure to wait for the unit to come to a complete stop before removing the container from the
base or the lid from the container.
11. To remove the lid, lift up on one lid flap while holding the container securely. The container can then be
emptied. If hot ingredients were blended, carefully hold the container handle, then place the container on
a flat surface.
FAQ
USING VARIABLE SPEED DIAL
2. How to determine the tamper is suitable for your blender?
Remove the lid plug and insert the tamper through the lid plug opening. The tamper should fit easily into
the opening. It should not come into contact with the blades no matter where you move the tamper inside
the container.
CAUTION
Moving Parts May
Become Hot with
Extended Use.
DO NOT touch.
- 11 -
CLEANING AND MAINTENANCE：
WARNING：
IF THE TAMPER TOUCHES THE BLADES AT ANY ANGLE, DO NOT USE THE TAMPER WITH YOUR
CONTAINER.
3. How to use the tamper?
CAUTION：
*To avoid inadvertent activation, unplug from outlet before assembling or disassembling parts, and before
cleaning.
* DON’T submerge the motor base into water or any other liquids.
DON’T let any liquid enter the motor.
Please refer to all instructions included in this book.
IMPORTANT: To ensure continued and effective performance, do not put the container, lid, or lid plug in
the dishwasher. Clean the appliance after every use.
1.To clean container, lid, lid plug, tamper and centering pad:
Self-Cleaning:
(without removing the container, lid and lid plug):
(1) Fill the container half full with warm water and add a couple of drops of dishwashing liquid.
(2) Make sure the 2-Part lid is securely snapped onto container.
(3) Perform one of the following procedures:
a. Make sure the marker on Variable Speed Dial is at 0. High/Variable Switch is at Variable position. Push
IMPORTANT! The splash disk (near the top of the tamper) and lid
prevent the tamper from hitting the blades when the lid is secured
properly in the locked position.
a. The container should not be more than two-thirds full when the
tamper is used.
b. If the food does not circulate, the blender may have trapped an
air bubble. While ensuring that the lid remains firmly in place,
carefully remove the lid plug.
c. Release the air bubble by inserting the tamper through the lid
plug opening.
d. Holding the tamper straight down may not help the ingredients
circulate. Point the tamper towards the sides or corners of the
container if necessary. DO NOT try to force the tamper deeper into
the container.
CAUTION:
The tamper can only be used when the main part of the lid is in
place. Hold the container while using the tamper. To avoid
overheating during blending, DO NOT use the tamper for more
than 30 consecutive seconds.
- 12 -
the On/Off Switch up to On position.
b. Slowly increase the variable speed to Variable 8.
c. Run the machine for 30 to 60 seconds. For best results, using short “High” several times.
d. Rotate the Variable Speed dial back to Variable 0 and turn off the machine.
e. Rinse clean under running water and dry thoroughly.
Hand Wash:
(remove the container, lid, and lid plug)
a. Wash the container, lid, and blades in warm soapy water. Rinse clean under running water and dry
thoroughly. Centering pad can be removed for more thorough cleaning.
CAUTION:
blades with care to avoid laceration caused by contact with sharp edges.
2. To clean motor base:
Clean the motor base with a soft, damp cloth to prevent scratching.
Do not submerge the motor base into water and or other liquids. Do not let any liquid enter the motor
HOW TO STORE?
1. Unplug the appliance.
2. Make sure all parts are clean & dry and placed in a clean and dry place.
3. Store the blender upright with the lid secured on top.
4. Store the unused portion of the power cord neatly underneath as picture.
Any other servicing should be performed by an authorized service representative.
- 13 -
TROUBLESHOOTING
WARRANTY AND SERVICE
WARNING:
To reduce the risk of shock and unintended operation, turn off power and unplug unit before
troubleshooting.
*1-Year Full Machine Warranty
This warranty coverage applies to the owner of this blender for personal household use only and to the
original product only and is not transferable. This Warranty does not apply to products for commercial,
rental or re-sale purposes.
homgeek warranty guarantees owner that if this blender fails within 1 year form the date of purchase due
to defects in materials and workmanship under normal household conditions, homgeek will in homgeek’s
sole discretion, elect to either(A)replace the Blender free of charge or(B) refund the owner, unless
homgeek receives prior written notice of the owner’s preference. In the rare event that a replacement unit
is issued, the warranty coverage ends six months after the receipt date of the replacement unit or the
remainder of the existing warranty, whichever is greater. If the unit id replaced, homgeek reserves the
right to replace the unit with one of equal or greater value.
This warranty is only valid if the blender is used and maintained in accordance with the instructions,
warnings and safeguards contained in the owner’s manual. This warranty only applies to product
Motor doesn’t start or
blades doesn’t rotate
Food is chopped too
finely or is too watery
1.If the blender does not start, check to make sure you have plugged
the unit in and that the On/Off switch is at On.
2.Make sure the container is securely placed on the motor base.
3.Check the fuse or circuit breaker.
The blender has dual-protection circuits.
a.For overheating.
b.For overloads.
If the motor overheats, allow it to cool for 1 hour; if overloaded,
unplug and plug again after 3 minutes.
The food has been over-processed. Use High mode for controlled
processing. Or stop blending if necessary.
The mixture is too thick. Add more liquid or use the tamper to help
push the ingredients toward the blades. The container should not be
filled more than 2/3 (for the sake of consistency) full when the tamper
is used during blending.
DO NOT use ice that has been sitting out or has started to melt. Use
ice straight from the freezer.
Food collects on lid
or on the sides of the
blades
You cannot create
snow from solid ice.
purchased through an authorized dealer.
This warranty does not cover damages or wear resulting from accident, misuse, abuse, commercial use,
or unauthorized adjustment and/or repair by homgeek. homgeek shall not be liable for loss of use or any
other incidental, consequential or indirect costs, expenses or damages. There are no express warranties
except as listed under the terms of this Limited Warranty. This warranty gives you specific legal rights, and
you may have other rights which vary from state to state.
If your appliance is found to be defective or fails to operate properly while in use under normal household
of purchase is required.
Shenzhen TOMTOP Technology Co., Ltd.
Add: G-4 Zone 5/F, No.1 Exchange Square, Huanan City, Pinghu Town, Longgang District, Shenzhen,
Guangdong, CN 18111
www.homgeek.com
- 14-
WARNING:
To reduce the risk of shock and unintended operation, turn off power and unplug unit before
troubleshooting.
*1-Year Full Machine Warranty
This warranty coverage applies to the owner of this blender for personal household use only and to the
original product only and is not transferable. This Warranty does not apply to products for commercial,
rental or re-sale purposes.
homgeek warranty guarantees owner that if this blender fails within 1 year form the date of purchase due
to defects in materials and workmanship under normal household conditions, homgeek will in homgeek’s
sole discretion, elect to either(A)replace the Blender free of charge or(B) refund the owner, unless
homgeek receives prior written notice of the owner’s preference. In the rare event that a replacement unit
is issued, the warranty coverage ends six months after the receipt date of the replacement unit or the
remainder of the existing warranty, whichever is greater. If the unit id replaced, homgeek reserves the
right to replace the unit with one of equal or greater value.
This warranty is only valid if the blender is used and maintained in accordance with the instructions,
warnings and safeguards contained in the owner’s manual. This warranty only applies to product
purchased through an authorized dealer.
This warranty does not cover damages or wear resulting from accident, misuse, abuse, commercial use,
or unauthorized adjustment and/or repair by homgeek. homgeek shall not be liable for loss of use or any
other incidental, consequential or indirect costs, expenses or damages. There are no express warranties
except as listed under the terms of this Limited Warranty. This warranty gives you specific legal rights, and
you may have other rights which vary from state to state.
If your appliance is found to be defective or fails to operate properly while in use under normal household
of purchase is required.
Shenzhen TOMTOP Technology Co., Ltd.
Add: G-4 Zone 5/F, No.1 Exchange Square, Huanan City, Pinghu Town, Longgang District, Shenzhen,
Guangdong, CN 18111
www.homgeek.com
- 15 -
Table of contents
Other homgeek Blender manuals
