Honeywell Home T6 Pro Smart User manual

Package Includes:
• T6 Pro Smart Thermostat
• UWP™ Mounting System
• Decorative Cover Plate
• Screws and anchors
• Thermostat literature
T6 Pro Smart
Programmable Thermostat
TH6220WF2006
TH6320WF2003
Professional Install
Guide
PM
Menu FanMode
Fan
Auto
Mode
Heat
Wake Away HomeSleep
Following Schedule
Search for local rebates: HoneywellHome.com/Rebates
33-00392EFS-01
Read before installing
Compatibility
• Compatible with most heating, cooling, and heat pump systems
• Required: 24 VAC power (“C” wire)
• Input: 24 V ~ @ 60 Hz, 1 A
• Does not work with electric baseboard heat (120V240V)
• Android or iOS smartphone or tablet
Customer assistance
WEB customer.resideo.com
PHONE 18006333991

2
Optional Decorative Cover Plate installation
NOTE: If Optional Cover Plate is not
required, see “UWP Mounting System
installation” on next page.
Use the Optional Cover Plate when you
need to cover paint gap from old thermo-
stat.
There are different cover plates depending
on when the thermostat was manufac-
tured.
For the square cover plate:
1. Separate the Cover Plate from
Mounting Plate.
2. Mount the Mounting Plate on to the
wall using any of the 8 screw holes.
Insert and tighten mounting screws
supplied with Cover Plate Kit. Do not
overtighten. See Figure 2. Make sure
the Mounting Plate is level.
3. Attach the UWP by hanging it on the
top hook of the Mounting Plate and
then snapping the bottom of the UWP
in place. See Figure 3.
4. Snap the Cover Plate onto the
Mounting Plate. See Figure 4.
Use supplied
screws and
wall anchors
4
3
2
1
For the rectangular cover plate:
1. Mount the Cover Plate on the wall using
any of the 6 screw holes. Insert and tighten
the mounting screws supplied with the
Cover Plate. Do not overtighten. See Figure
1. Make sure the Cover Plate is level. Attach
the UWP by hanging it on the top hook
of the Cover Plate and then snapping the
bottom of the UWP in place. See Figure 2.
2. If there are no existing wall anchors:
a. Position the Cover Plate on wall. Level
and mark hole positions. See Figure 1.
b. Drill holes at marked positions, and then
lightly tap supplied wall anchors into the
wall using a hammer.
•If your box contains red anchors, drill
7/32” (5.6 mm) holes.
•If your box contains yellow anchors,
drill 3/16” (4.8 mm) holes.
•Use 2x supplied screws (#8 11/2”
(38 mm) for red anchors and #6
11/2” (38 mm) for yellow anchors).
2
1

3
UWP Mounting System installation
1. Open package to find the UWP.
See Figure 1.
2. Position the UWP on the wall. Level and
mark hole positions. See Figure 2.
Drill holes at marked positions, and then
lightly tap supplied wall anchors into wall
using a hammer.
‒If your box contains red anchors, drill
7/32” (5.6 mm) holes for drywall.
If your box contains yellow anchors, drill
3/16” (4.8 mm) holes for drywall.
3. Pull the door open and insert wires
through wiring hole of the UWP. See
Figure 3.
4. Place the UWP over the wall anchors.
Insert and tighten mounting screws supplied with
the UWP. Do not overtighten. Tighten until the UWP
no longer moves. Close the door. See Figure 4.
1
2
3
4
Use 3x supplied screws
(#8 11/2" [38 mm] for
red anchors and #6 11/2
[38 mm] for yellow anchors)
1
2
3 4
1 2
3
4

4
Terminal designations
Conventional Systems Heat pump systems
Terminal Description Terminal Description
S/S Input for a wired indoor,
outdoor sensor S/S Input for a wired indoor, outdoor sensor
Y Compressor Stage 1 Y Compressor Stage 1
Y2 Compressor Stage 2 Y2 Compressor Stage 2
G Fan Relay G Fan Relay
C24VAC Common wire from secondary side of cooling
transformer (if 2 transformers) C24VAC Common wire from
secondary side of cooling
transformer
K* Connect to K on C-wire
adaptor K* Connect to K on C-wire adaptor
U/U** Relay for ventilation U/U** Relay for ventilation
A L/A Connect to compressor
monitor
W Heat Stage 1 O/B Changeover valve for heat
pumps
W2 Heat Stage 2 Aux Backup Heat
E Emergency Heat
R 24 VAC Heating transformer R 24 VAC Heating transformer
Rc 24 VAC Cooling transformer Rc 24 VAC Cooling transformer
* The THP9045A1098 C-wire adaptor is used on heat/cool systems when you only have four wires at
the thermostat and you need a fifth wire for a common wire. Use the K terminal in place of the Y and
G terminals on conventional or heat pump systems to provide control of the fan and the compressor
through a single wire—the unused wire then becomes your common wire. See THP9045 instructions
for more information.
** Ventilation is not available on all models. When the U slider is in the down position (2 wires), the U
contacts are a dry set of contacts. If your ventilation system requires 24 volts, move the U slider to the
up position (1 wire). Lower U terminal is internally jumped to the Rc terminal. In this application, you
would hook up one wire from your damper to the upper U terminal and the other to the common side of
the transformer.
Wiring UWP
Push down on the tabs to put the wires into the inner holes of their corresponding terminals
on the UWP (one wire per terminal) until they are firmly in place. Gently tug on the wires to
verify they are secure. If you need to release the wires again, push down the terminal tabs
on the sides of the UWP.
This wiring is just an example,
yours may vary.

5
Setting Slider Tabs
Set R Slider Tab, see Figure 1.
• Use built-in jumper (R Slider Tab)
to differentiate between one or two
transformer systems.
• If there is only one R wire, and it is
connected to the R, Rc, or RH terminal
on the old thermostat, set the slider to
the up position (1 wire).
• If there is one wire connected to the R
terminal and one wire connected to the
Rc terminal, set the slider to the down
position (2 wires).
Set U Slider Tab, see Figure 2.
• Use built-in jumper (U Slider Tab) of
relay to wire ventilation. Please note
that ventilation is not supported on all
models.
• When the U Slider Tab is in the down
position (2 wires) the U contacts are a
dry set of contacts.
• If the ventilator is powered by the
cooling transformer, move the jumper
switch to the up position (1 wire). With
this switch set to 1 wire, the lower U
terminal is internally jumped to the Rc
terminal. In this application, hook up
one wire from the vent damper to the U
terminal and the other to the common
side of the cooling system transformer.
2
1

6
Wiring
1H/1C System (1 transformer)
RPower
Rc [R+Rc joined by Slider Tab]
YCompressor contactor
C24VAC common
WHeat relay
GFan relay
NOTES:
1 Available wiring configurations differ by product models/product numbers.
2 Use 18 to 22 gauge thermostat wire. Shielded cable is not required.
3 Set the R Slider Tab on the UWP to the up position (1 wire) for 1 transformer
systems or the down position (2 wires) for 2 transformer systems. See "Setting
Slider Tabs" on page 5.
4 Set the U Slider Tab to the up position (1 wire) for non-powered ventilation or the
down position (2 wires) for powered ventilation. See "Setting Slider Tabs" on page
5.
Conventional systems
1H/1C System (2 transformers)
RPower (heating transformer)
Rc Power (cooling transformer)
YCompressor contactor
C24 VAC common from cooling transformer
WHeat relay
GFan relay
2H/2C System (1 transformer)
RPower
Rc [R+Rc joined by Slider Tab]
Y Compressor contactor (stage 1)
C24VAC common
WHeat relay (stage 1)
GFan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
Hot Water Relay Panel
RPower
Rc [R+Rc joined by Slider Tab]
WHeat Relay
C24VAC common
Heat-only System with Fan
RPower
Rc [R+Rc joined by Slider Tab]
C24VAC common
WHeat relay
GFan relay
Cool-only System with Fan
RPower
Rc [R+Rc joined by Slider Tab]
YCompressor contactor
C24VAC common
GFan relay
NOTE: If the panel does not provide 24 volts AC
at R and C, set the slider to down position and
wire a separate transformer to Rc and C.

7
Heat pumps systems
1H/1C Heat Pump System
RPower
Rc [R+Rc joined by Slider Tab]
YCompressor contactor
C24VAC common
O/B Changeover valve
GFan relay
2H/1C Heat Pump System
RPower
Rc [R+Rc joined by Slider Tab]
YCompressor contactor
C24VAC common
O/B Changeover valve
GFan relay
Aux Auxiliary heat*
EEmergency heat relay*
LHeat pump fault input
NOTE: If dual fuel, TH6320WF2003
model needed.
2H/2C Heat Pump System
RPower
Rc [R+Rc joined by Slider Tab]
YCompressor contactor (stage 1)
C24VAC common
O/B Changeover valve
GFan relay
Y2 Compressor contactor (stage 2)
LHeat pump fault input
3H/2C Heat Pump System
RPower
Rc [R+Rc joined by Slider Tab]
YCompressor contactor (stage 1)
C24VAC common
O/B Changeover valve
GFan relay
Aux Auxiliary heat*
EEmergency heat relay*
Y2 Compressor contactor (stage 2)
LHeat pump fault input
NOTE: TH6320WF2003 only.
* If you do not have separate wires for the Aux and E terminals, connect the wire to the Aux terminal.
NOTE: Do NOT use Wfor heat pump applications. Auxiliary heat must wire to AUX or E.

8
Ventilation systems
NOTE: Ventilation is not available on all models.
Mounting thermostat
1 Push excess wire back into the wall
opening.
2 Close the UWP door. It should remain
closed without bulging.
3 Align the UWP with the thermostat, and
push gently until the thermostat snaps in
place.
4 If needed, gently pull to remove the
thermostat from the UWP.
5 Search for local rebates:
Your thermostat may now be eligible for
local rebates. Search for offers in your area
at HoneywellHome.com/Rebates
Using U Slider Tab
Wired to ERV/HRV whole
house ventilator with internal
power supply.
Wired to fresh air damper
powered by furnace
transformer.
11 12

9
Installer setup – using the thermostat
Setup using the thermostat
• After the thermostat has powered up,
touch START SETUP on the thermostat.
You’ll be asked if you want to perform
setup via app. Touch No.
• Touch or to toggle between
Installer Set Up (ISU) options.
• Touch Edit or touch text area, and
then touch or to edit default
setup option.
• Touch Done or touch text area to
confirm the setting or press Cancel.
• Touch or to continue to setup
another ISU option.
NOTES:
• To see a list of all setup parameters,
go to "Installer setup options (ISU) –
advanced menu" on page 12. The
thermostat displays the ISU name
and the ISU number.
• To finish setup and save your settings,
scroll to the Finish screen at the end of
the ISU list.
• Touch Select or touch text area to
save changes and exit, or touch to
return to initial setup screen.
Cancel
Done
Edit ISU
ISU #
ISU option blinking
Cancels ISU option
selection, go back
to view ISU
Arrow buttons used
to scroll through ISU
options
Saves selected ISU
option moves on to
the next ISU screen
Edit
View ISU
ISU #ISU name and
option (scrolling) Arrow buttons used to scroll through
ISUs
Select
No Yes
Back

10
Advanced menu options
Device Setup
This is used to access the device ISU setting.
Screen Lock
The thermostat touch screen can be set to lock
fully or partially.
Rater View
A read only place to view all the ventilation
settings.
System Test
Test the heating and cooling system.
Range Stop (Temperature)
Set the minimum, maximum, cool and heat
temperature set points.
Reset
Access all reset options on the thermostat.
This is the only place to access factory reset.
Installer setup – using the Resideo Pro app
Setup using the app
Download the Resideo Pro or Honeywell
Home app from App Store or Google
Play to install and personally invite
your customer to connect the installed
thermostat at the same time.
With the Resideo Pro app, you can
personally invite your customer to
connect their account.
Installer setup – advanced menu
To access the advanced menu, press and hold the Menu button for 5 seconds.
Touch or to go through the options in the advanced menu.
AM
Menu FanMode
Fan
Auto
Mode
Heat
Wake Away Home Sleep
Following Schedule