Honeywell Home Y87RF User manual

EN | Installation Guide
Installation Instructions
3. Unclip the
mounting plate.
Press the top of
the thermostat
downwards,
pull it loose and
tilt forwards.
2. First remove the dial.
1. Locate the thermostat
in a suitable location:
5. Remove the
protective tab
between the
batteries.
4. Mount directly
to the wall.
The plugs and
mounting screws
required are
supplied.
Plugs
Screws
7. Replace the dial.
6. Attach the
thermostat to
the mounting
plate. Step 1
Hook in
here
Step 2
Click into
place
50094157-014 B
2. You can now bind
the Single Zone
Thermostat. Touch
and hold on the
left touch zone
for approximately
10 seconds
3. The screen now
flashes bo.
Rotate the dial one
click clockwise
until it flashes Co – this is the binding
mode for binding to Evotouch.
By rotating the dial, other binding
modes are accessible:
a) bo for binding to boiler relays/
controls like BDR91 or R8810.
b) Hc for binding to an underfloor
heating control like HCE80/HCC80
1. First put the other RF device into
binding mode. You may need to cancel
or reset any prior binding information.
Note: for more information about
binding modes, see the instructions
supplied with the other RF device.
4. When the required symbol is flashing,
briefly touch the left touch zone on
the Single Zone Thermostat to send
the binding signal, at which point the
symbol will flash several times.
Binding
Before the Single Zone Thermostat
can communicate with other RF
devices it must be bound to them.
Attention: if the Single Zone Thermostat
is replaced, the other RF equipment must
have their bindings reset in order to allow
the replacement product to be bound.
Touch zones.
There are two
touch zones
just below the
thermostat display,
which are used
to access menus
and functions.
10s
Away from draughts Away from direct sunlight
1.2 - 1.5 m
Away from heat sources
Y87RF Single Zone Thermostat

Installation Menu
The Thermostat has an Installation
Menu that is used to set the minimum
and maximum temperature limits
and the off temperature setting.
Maximum and minimum temperatures:
The maximum temperature you can set your
thermostat to is 35°C and the minimum is 5°C.
The off temperature:
If the thermostat is operated remotely, this
is the temperature value that is used when
it is switched off from the remote app.
4. Touch the left touch
zone to display the off
temperature setting.
Change this using the
setting ring as before.
5. The Installation Menu
closes automatically
10 seconds after
the last action.
2. The maximum
temperature limit is
now displayed. The
setting can be changed
using the setting ring.
There is no need to
confirm the value.
3. While this setting is
flashing, touch the left
touch zone briefly to
display the minimum
temperature limit. This
can also be changed
using the setting ring.
1. Rotate the setting
ring fully to the left
until the minimum
value is shown. When
the value starts
flashing, touch and
hold on both left and
right touch zones
for approximately
10 seconds.
Activate the Installation Menu as follows:
10s 10s
Printed in EU.
(EU) 811/2013
© 2020 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell International Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
Pittway Sarl, Z.A. La Pièce 4,
1180 Rolle, Switzerland
Country of origin : UK
For support:
Resideo
200 Berkshire Place
Winnersh Triangle, Berkshire
RG41 5R
Phone: [phone]
Approvals:
Hereby, Pittway Sarl declares that the radio equipment type Y87RF is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address: https://hwllhome.co/DoC
RF (868MHz): Receiver Category 2, Max RF Power 25mW, 868–868.6MHz (868.3MHz)