Honeywell Home TL8130A1005 User manual

Owner’s Guide
TL8130A1005
7-Day Programmable Thermostat
69-1805EF-07

Overview
Before you start..................................................1
About your thermostat........................................2
Controls..............................................................3
Display ...............................................................4
Installation
Installing the thermostat .....................................5
Wiring diagram ...................................................6
Setting the configuration switches......................7
Setup
Time and day......................................................8
Daylight Saving Time .........................................9
Preset temperatures.........................................10
Default schedule ..............................................11
Modifying the schedule ....................................12
Operation
Running the schedule (Automatic mode) .........13
Temporary override of schedule.......................13
Permanent override (Manual mode) ...............14
Appendices
Error messages................................................15
Technical specifications....................................16
Warranty...........................................................17
Customer assistance........................................18
Table of contents

TL8130A1005
1
Read the entire document
CAUTION:
• Installation must be carried out by a certified electrician and must comply with national and local
electrical codes.
• To prevent severe shock or electrocution, always cut the power at the service panel before working
with wiring.
• Use this thermostat for resistive loads only.
• Do NOT install the thermostat in an area where it can be exposed to water or rain.
• Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind a
door), direct sunlight or concealed chimney or stove pipes.
• For a new installation, choose a location about 1.5 m (5 ft.) above the floor.
• Install the thermostat on an inside wall facing the heating system.
• Install the thermostat onto an electrical box.
• Use special CO/ALR solderless connectors if you connect the thermostat to aluminum wires.
• Keep the thermostat's top and bottom air vents (openings) clean and unobstructed at all times.
Before you start

Owner’s Guide
2
Honeywell Home’s TL8130A1005 thermostat can be connected to an electric
heater to control the room temperature.
Supplied Parts
• One (1) thermostat
• Two (2) mounting screws
• Four (4) solderless connectors for copper wires
About your thermostat

TL8130A1005
3
Controls
On/Standby switch*
Day button
Temperature adjustment buttons**
Program button
Mode selection / program exit
Preset temperature buttons
(see page 10)
Backlight button**
Program clear button
Hour button
Minutes button
*
Place at Standby to cut power to the heater (e.g., in the summer). This will not affect the time and temperature settings.
** When the backlight button or either of the buttons is pressed, the display illuminates for 12 seconds.

Owner’s Guide
4
Display
Temperature*
Operation mode icon
(see pages 13 & 14)
Period (see page 11)
Time
Number of flames varies
according to heating intensity
Preset temperature icon (see page 10)
Appears when the setpoint
temperature is displayed*
Indicates this thermostat model is used
to control the ambient temperature
Day
* The thermostat normally displays the actual (measured) temperature. To view the setpoint temperature, briefly press
either of the buttons. The setpoint will appear for 5 seconds. To change the setpoint temperature, press one of the
buttons until the desired temperature is displayed. To scroll faster, press and hold the button.

TL8130A1005
5
1) Turn the heating system off at the main electrical panel.
2) Loosen the bottom screw and remove the thermostat faceplate
from its wallplate. (The screw cannot be completely removed.)
3) Connect the thermostat to the load and to the power supply
(see page 6).
4) Install the wallplate to the electrical box using the provided
screws.
5) If necessary, set the configuration switches on the back of the
faceplate (see page 7).
6) Install the faceplate back on the wallplate and tighten the
screw. If there is a sticker on the screen, peel it off.
7) You can now return power to the heating system at the main
electrical panel.
Installing the thermostat
Wallplate
Faceplate

Owner’s Guide
6
NOTE: Connect the wires using the provided solderless connectors for copper wires.
Wiring diagram
Power
Load

TL8130A1005
7
Configuration switches are on the back of the faceplate.
Set the configuration switches
# Configurations Up Down
1 Display format °F / 12 h °C / 24 h
2Early Start1
1. Early Start is used in Automatic mode only. When Early Start is enabled (on), the thermostat
determines when to start heating so the Comfort temperature is attained at the beginning of
periods 1 and 3. When Early Start is disabled (off), heating starts only at the beginning of
periods 1 and 3; thus there is a delay before the Comfort temperature is reached.
Enable Disable
3 Not used

Owner’s Guide
8
To set the clock and the day:
1) Press the Hour button to set the hour.
2) Press the Min button to set the minutes.
3) Press the Day button to set the day.
4) Press the Mode/Ret button to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is
pressed for 60 seconds.
Time and day