Honeywell NW0130U20XXX User manual

11”
Fold
Fold
Fold
17” Fold
Fold
Fold
EN | 2
INSTALLATION
CAUTION: Before beginning installation turn off the circuit breaker and light switch.
STEP 1
STEP 3
RECOMMENDED: Wrap each wire nut with electrical tape (not included) after wires have
been attached.
Note: Avoid aiming the motion sensor at:
• Objects that change temperature rapidly to prevent false triggering, such as heating vents
and air conditioners.
• Moving objects such as trees and street trafc.
The lamp head (Part G) can be adjusted up/down and left/right for optimal lighting coverage. The
motion sensor (Part J) can be adjusted up/down toward desired detection area.
EN | 1
SAFETY INFORMATION
PRE-INSTALLATION
• To reduce the risk of electrical shock or other personal injury, ensure the power is turned
OFF at the fuse or breaker box before making any electrical connections.
• For outdoor use only.
• Must be connected to 120 volt, 60 Hz power source.
• Fixture should be mounted to a grounded junction box marked for use in wet locations.
• Suitable for wall mount.
• NOT suitable for ground locations. Minimum of 6 feet or higher.
• Wall lantern should be installed by a qualified electrician or person experienced with
household wiring. The electrical system, and method of electrical connection of the fixture,
must be in accordance with the National Electrical Code and local building codes.
PLANNING INSTALLATION
• Turn off the electrical power at the fuse or circuit breaker box before installing or servicing
any part of this fixture.
• Carefully remove the fixture from the carton and check that all parts are included. Be careful
not to misplace any of the screws or parts needed for installing the fixture.
HARDWARE INCLUDED
EN | 3
F:
Washer (1)
Ø8.5 mm x 1 mm
A:
Phillips Head Screws (2)
8-32UNC x 20
WARNING: Read all safety precautions and installation instructions carefully before installing or
servicing this fixture. Failure to comply with these instructions could result in a potentially fatal electric
shock, fire, and/or property damage.
IMPORTANT: lisez attentivement toutes les précautions de sécurité et les installations avant
d'installer ou de réparer ce luminaire. Le non respect de ces instructions peut entraîner un choc
électrique et / ou des dégâts matériels potentiellement fatals.
SUITABLE FOR WET LOCATIONS ! CONSULT A QUALIFIED ELECTRICIAN TO ENSURE
CORRECT BRANCH CIRCUIT CONDUCTOR! MINIMUM 90° C SUPPLY CONDUCTORS!
ADAPTÉ AUX LIEUX MOUILLÉS! CONSULTER UN ÉLECTRICIEN QUALIFIÉ POUR
ASSURER UN CONDUCTEUR DE CIRCUIT DE BRANCHE APPROPRIÉ! CONDUCTEURS
D'ALIMENTATION MINIMUM DE 90° C!
G- Lamp Head
H- Screw Nut
I - Lamp base
J - Motion Sensor
PARTS
C:
Waterproof pad (1)
Ø132 mm x 3 mm
D:
Mounting Bracket (1)
100 mm x 21 mm
B:
Wire Nut (3)
P2 10 mm x 17.2 mm
E:
Phillips Head Screws (1)
M5 x 42mm
G
G
I
J
J
H
(Figure 1)
(Figure 2)
1.
OPERATION
Position the mounting bracket (Part D) to the junction box (Not Included) and secure using
screws (Part A). The AC wires through the waterproof pad (Part C), and the waterproof pad
(Part C) can be pasted to the lamp base (Part I). Then connect the AC wires to the
corresponding wires (BLACK to BLACK, WHITE to WHITE and GROUND to GROUND) in the
junction box using the wire nuts (Part B). (Figure 1)
STEP 2
Making screw (Part E) through the washer (Part F) and the hole of the lamp base (Part I),
then fix the lamp to the mounting bracket, adjust the lamp to the proper position and
tighten the screw.
Note: The lamp heads should be installed horizentally.
FUNCTION SWITCH: K - Motion sensor sensitivity switch
L - Timer switch
M - Link button
1. Motion sensor sensitivity switch (Part K), detection distance can be adjusted to
Min. 6.6 feet (2m), Max. 39.4 feet (12m).
2. Timing switch (Part L), the TEST option is used for adjust detection distance during
the day time installation, the light will last 12s when activated.
After your test finished, select your favorite motion activated duration time,
1min/5min/10min.
Note: If you go back to TEST mode and light isn’t lit, try again after power off/on.
3. Link set-up:
a. Can be connected more than 2 lights, make sure all the light are power on and
move to TEST position, select one as the parent light and others as the child lights.
b. Press the link button (Part M) of the child light to flashing status, keep on the link
button (Part M) for 3 seconds of parent light and waiting for code matching, all lights
flashing, once the parent light and child light stop flashing or being on, it confirms
code matching is completed and products are linked, release button.
c. When any of the lights are triggered by motion detector, all lights will activate.
Note: When light triggered by motion, detection angle is 180°. Light's use radio
frequency technology to link, and should not be greater than 98 feet between the
neighboring/adjacent lights.
If you buy a new light and want to link , you can re-set up.
Note: Affected by the installation environment, the lamp will be delayed to light.
It is a normal case.
4. Relieve linkable function: keep on the link button (Part M) for 3 seconds, the light
will work independently.
L
KM
B
D
A
C
E
F

LED Outdoor Security Flood Light
Use and Care Guide
Read and Save this Instructions BeforeUse
EN
Model: NW0130U20XXX
11”
Fold
Fold
Fold
17”Fold
Fold
Fold
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
**********************************************************************************************
NOTES:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING:
TROUBLE SHOOTING
PROBLEM
Light will not come on.
A. Light switch is turned off.
B. Fuse is blown or circuit breaker is
turned off.
C. Incorrect circuit wiring.
D. There is too bright light from other
lamps to the sensor head.
E. The lamp is in a brighter
environment.
A. Turn light switch on.
B. Replace fuse or turn circuit breaker
on.
C. Verify that fixture is wired properly.
D. Install the lamp farther away from
other one relative brightly.
E. Install the lamp in a dark
environment.
A. The lamp may be installed in a
relatively dark location.
B. The ON-TIME setting option is set to
TEST mode where has no light control
function.
A. Reposition the lamp.
B. Switch the ON-TIME setting option
to another time location.
POSSIBLE CAUSE SOLUTION
Lights come on during
the day.
A. Lamp infrared motion sensor may be
sensing moving objects such as trees,
traffic, etc.
B. Lamp infrared sensitivity be set too
high.
A. Reposition the lamp.
B. Reduce sensitivity of the motion
sensor.
Lights come on for no
apparent reason.
A. Lamp too far from lamp or blocked by
wall.
The distance between two lights is too far
or there is obstacle between two lights
A. Re-install the lights and keep the
distance between two light within 98 feet
and make sure there is no obstacle
between two lights.
LINK cannot be
synchronized after
successful connection.
A. Failed to connect as required by LINK
operation.
A. Reconnect according to the LINK
operation.
LINK cannot be connected
successfully.
Sky Rich Star Limited
UNIT E, 10/F, WORLDWIDE CENTRE,
123 TUNG CHAU STREET, TAI KOK TSUI,
KL, HONG KONG
Toll-free: 1-877-723-0723
Made in China
© 2019 Sky Rich Star Limited, all rights reserved.
The Honeywell Trademark is used under license
from Honeywell International Inc.
Honeywell International Inc. makes no
representations or warranties with respect
to this product. This product is manufactured for
Sky Rich Star Limited.