Honeywell Dolphin CK65 User manual

Dolphin™ CK65
powered by Android™
Quick Start Guide
CK65-A-EN-QS-01 Rev A
4/19

2
Out of the Box
Make sure that your shipping box contains these items:
• CK65 mobile computer
(Model CK65L0N)
• Rechargeable 3.6 VDC Li-ion battery
•Handstrap
• Product documentation
If you ordered accessories for your mobile computer, verify that
they are also included with the order. Be sure to keep the original
packaging in case you need to return the mobile computer for
service.
Memory Card Specifications
Honeywell recommends the use of Single Level Cell (SLC)
industrial grade microSD™ or microSDHC™ memory cards with
Dolphin mobile computers for maximum performance and
durability. Contact a Honeywell sales representative for
additional information on qualified memory card options.

3
Mobile Computer Features
Microphone
Power Button
Ambient Light
Sensor
Touch Panel
Keyboard
(model dependent)
Notification/Scan/
Battery Status LEDs
Imager (LED / Laser Aperture)
Keypad Status LEDs
Scan Buttons
All Imagers

4
Camera Lens
and Flash
Battery Latch
(under hand strap)
Laser Safety
Label Location
Scan/Aux Button
Hand Strap
I/O Connector
Scan/Aux
Button
CK65 Model with N6703 Imager
MicroSD Card Door
(battery and hand strap removed)
All CK65 Units

5
Camera Lens
and Flash
MicroSD Card Door
(battery and hand strap removed)
Battery Latch
(under hand strap)
Laser Safety
Label Location
Scan/Aux Button
Hand Strap
I/O Connector
Scan/Aux
Button
CK65 Model with EX20 Imager
All CK65 Units

6
Install a microSD Card (Optional)
See Install the Battery for hand strap release information.
Format the microSD card before initial use.
Always power off the computer before attempting to
install or remove a card.
1 2
4
3

7
Install the Battery
The CK65 mobile computer ships with a Li-ion 3.6 VDC,
18 watt-hour battery manufactured for Honeywell International
Inc.
Use only Honeywell Li-ion battery pack models
AB17, AB18, and 1001AB01.
Ensure all components are dry prior to placing the
battery in the computer. Mating wet components may
cause damage not covered by the warranty.
1
2
3
4

8
Charge the Mobile Computer
The CK65 mobile computer ships with a partially charged
battery. Charge the battery with a CK3 Series charging device for
a minimum of 4 hours. Using the computer while charging the
battery increases the time required to reach a full charge.
CK65 mobile computers are designed for use with CK3 Series
charging accessories.
We recommend the use of Honeywell accessories and
power adapters. Use of any non-Honeywell
accessories or power adapters may cause damage not
covered by the warranty.
Ensure all components are dry prior to mating the
computers and batteries with peripheral devices.
Mating wet components may cause damage not
covered by the warranty.

9
Turn Power On/Off
The first time you power on the computer, a Welcome screen
appears. You can either scan a configuration bar code or use the
Wizard to manually set up the computer. Once setup is
complete, the Welcome screen no longer appears on startup
and Provisioning mode is automatically turned off (disabled).
To turn the computer on:
•PressandholdthePower button for approximately 3 seconds,
and then release.
To turn the computer off:
1. Press and hold the Power button until the options menu
appears.
2. Touch Power off.
Battery Replacement
Swap Battery Mode
You should always place the computer in Swap Battery mode
before removing the battery. Swap Battery mode places the
computer in a low power state so that the battery can be
removed for a short time.
To activate Swap Battery mode:
1. Press and hold the Power button until the options menu
appears.
2. Touch Swap Battery and follow the on-screen instructions.
3. Once you replace the battery, press the Power button.

10
Sleep Mode
Sleep mode automatically turns the touch panel display off and
locks the computer to save battery power when the computer is
inactive for a programmed period of time.
1. Press and release the Power button to wake the computer.
2. Drag the toward the top of the display to unlock the
computer.
Adjust the Display Sleep Time
To adjust the amount of time before the display sleeps after
inactivity:
1. Touch > Settings > Display > Advanced > Sleep.
2. Select the amount of time before the display goes to sleep.
3. Touch to return to the Home screen.