Honeywell PRO-2200 User manual

PRO-2200
Output Module
Installation Manual
Part Number: PRO22OUT
TD1142 rev0501
A division of Northern Computers, Inc.

PRO-2200 Output Module PRO22OUT 3Installation Guide
Contents
Warnings and Cautions........................................................................................4
Disclaimer...........................................................................................................6
Product Liability; Mutual Indemnification ................................................................6
Unpacking Procedure...........................................................................................6
Shipping Instructions ............................................................................................7
Limited Warranty..................................................................................................7
Confidentiality .....................................................................................................8
Description..........................................................................................................9
Set Up ...............................................................................................................9
LED Operation ..................................................................................................11
Power ...............................................................................................................11
Communications ...............................................................................................11
Alarm Contact Wiring ........................................................................................12
Control Output Wiring .......................................................................................12
Mounting Options .............................................................................................13
Suggested Installation Sequence .........................................................................13
Specification......................................................................................................14
Wiring Diagram for Connectors 1 through 8........................................................15
Wiring Diagram for Connectors 7 through 11......................................................16
Notes................................................................................................................17

4 PRO-2200 Output Module PRO22OUTInstallation Guide
Warnings and Cautions
WARNING
Before installation, TURN OFF the external circuit breaker which supplies power to the
system.
Before connecting the device to the power supply, verify that the output voltage is within
specifications of the power supply.
Do not apply power to the system until after the installation has been completed.
Personal injury or death could occur, and the equipment could be damaged beyond
repair, if theseWARNINGSare not observed!
WARNING
Fire Safety and Liability Notice
Never connect card readers to any critical entry, exit door, barrier, elevator or gate
without providing an alternative exit in accordance with all fire and life safety codes
pertinent to the installation.These fire and safety codes vary from city to city and you
must get approval from local fire officials whenever using an electronic product to control
a door or other barrier.Use of egress buttons, for example, may be illegal in some cities.
In most applications, single action exit without prior knowledge of what to do is a life
safety requirement.Always make certain that any required approvals are obtained in
writing.DO NOT ACCEPTVERBAL APPROVALS,THEY ARE NOTVALID.
Engineered Systems never recommends using the PRO-2200 or related products as a
primarywarning or monitoringsystem. Primary warning or monitoring systems should
always meet local fire and safety code requirements.The installer must also test the
system on a regular basis by instructing the end user in appropriate daily testing proce-
dures.Failure to test a system regularly could make installer liable for damages to the end
user if a problem occurs.
WARNING
EARTH groundall enclosures, for proper installation.
WARNING
Use suppressors on all door strikes. Use S-4 suppressors for installation. Engineering
Systems recommends only DC strikes.
The information in this document is subject to change without notice.

PRO-2200 Output Module PRO22OUT 5Installation Guide
CAUTION
IF ANY DAMAGETO THE SHIPMENT IS NOTICED, A CLAIM MUST BE FILED WITH
THE COMMERCIAL CARRIER RESPONSIBLE.
CAUTION
Electro-static discharge can damage CMOS integrated circuits and modules.
To prevent damage always follow these procedures:
Use static shield packaging and containers to transport all electronic components,
including completed reader assemblies.
Handle all ESD sensitive components at an approved static controlled workstation.These
workstations consist of a desk mat, floor mat and an ESD wrist strap.Workstations are
available from various vendors.
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
NOTICE
This document and the data in it shall not be duplicated, used or disclosed to others for
procurement or manufacture, except as authorized by and with the written permission of,
Engineering Systems.The information contained in this document or in the product itself
is considered the exclusive property and trade secrets of Engineering Systems.Copyright
laws of the United States protect all information in this document or in the software
product itself.
NOTICE
Any use of this product is subject to the terms and acceptance of the Engineering
Systems Software Agreement. Please request a copy from Engineering Systems, and
reviewtheagreement carefully.

6 PRO-2200 Output Module PRO22OUTInstallation Guide
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component thereof
has caused personal injury or damage to property of others, Customer shall immediately
notify Engineering Systems in writing of all such claims. Engineering Systems shall
defend or settle such claims and shall indemnify and hold Customer harmless for any
costsor damages includingreasonable attorneys’ feeswhich Customer maybe required
to pay as a result of the defective Product or the negligence of Engineering Systems, its
agents, or its employees.
Customer shall hold harmless and indemnify Engineering Systems from and against all
claims, demands, losses and liability arising out of damage to property or injury to
persons occasioned by or in connection with the acts or omissions of Customer and its
agents and employees, and from and against all claims, demands, losses and liability for
costs of fees, including reasonable attorneys’ fees, in connection therewith.
Unpacking Procedure
CAUTION
If any damage to the shipment is noticed before unpacking, a claim must be filed with the
commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.
Follow these steps to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all packing materials. They may be used again for reshipment
ofthe equipment, if needed.
2. Inspect the contents for shortage.If items are missing items, contact the order entry
department at800-323-4576.
3. Visually check contents. If damage is discovered, perform the following:
If shipping caused damage to the unit, a claim must be filed with the
commercialcarrier.
If any other defect is apparent, call 800-323-4576 for a return authorization.

PRO-2200 Output Module PRO22OUT 7Installation Guide
Shipping Instructions
To ship equipment back to Engineering Systems:
1.Contactthe customerservicedepartmentat 800-323-4576,before returning equipment.
Beforecalling, please haveavailable:
•A description of the problem or reason for returning the equipment.
•Original purchase order number, invoice number and if the unit is under warranty.
•A new purchase order number if the unit is not under warranty
2. Obtain the Return Authorization Number (RMA) from the customer service
department at800-323-4576.
3.Show the RMA number on all packages shipped.Packages, which are not marked with
an RMA number will be refused at the factory and returned to you COD.
4.Carefully pack the equipment for shipment. Use the original packingmaterial whenever
possible.
Limited Warranty
All Products sold or licensed by Engineering Systems include a warranty registration card
which must be completed and returned to Engineering Systems by or on behalf of the end
user in order for Engineering Systems to provide warranty service, repair, credit or ex-
change. All warranty work shall be handled through Customer which shall notify Engineer-
ing Systems and apply for a Return Merchandise Authorization (RMA) number prior to
returning any Product for service, repair, credit or exchange. Engineering Systems
warrants that its Products shall be free from defects in materials and workmanship for a
period of two years from date of shipment of the Product to Customer.The warranty on
Terminals, Printers, Communications Products and Upgrade kits is 90 days from date of
shipment. Satisfaction of this warranty shall be limited to repair or replacement of Prod-
ucts which are defective or defective under normal use. Engineering Systems’warranty
shall not extend to any Product which, upon examination, is determined to be defective as
a result of misuse, improper storage, incorrect installation, operation or maintenance,
alteration, modification, accident or unusual deterioration of the Product due to physical
environments in excess of the limits set forth in Product manuals.THERE ARE NO
WARRANTIESWHICH EXTEND BEYONDTHIS PROVISION.THISWARRANTY IS IN
LIEUOF ALL OTHERWARRANTIESWHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDINGIMPLIEDWARRANTIESOF MERCHANTABILITY OR FITNESSFOR ANY
PARTICULAR PURPOSE.NO REPRESENTATIONORWARRANTYOFTHEDISTRIBU-
TOR SHALL EXTENDTHE LIABILITY OR RESPONSIBILITY OFTHE MANUFACTURER
BEYONDTHETERMS OFTHIS PROVISION.IN NO EVENT SHALL ENGINEERING
SYSTEMS BE LIABLE FOR ANY RE-PROCUREMENT COSTS, LOSS OF PROFITS,
LOSS OF USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGESTO ANY
PERSON RESULTING FROMTHE USE OF ENGINEERING SYSTEMS’PRODUCTS.

8 PRO-2200 Output Module PRO22OUTInstallation Guide
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and other
materials furnished by Engineering Systems relating to the design, use and service of the
Products shall remain confidential and shall constitute proprietary rights of Engineering
Systems and Customer agrees to treat such information as confidential. Customer shall
acquire no rights in the design of the Products or the related materials except to use such
information solely for the purpose of and only during the time it sells the Products. Cus-
tomer shall not copy the design of any of the Products or use or cause to be used any
Product design or related materials for its own benefit or for the benefit of any other party.
The covenants contained in this section shall remain effective throughout the term of this
Agreement and thereafter unless specifically waived by Engineering Systems in writing.

PRO-2200 Output Module PRO22OUT 9Installation Guide
N-1000-IV FourN-1000-IV Four
N-1000-IV FourN-1000-IV Four
N-1000-IV Four
Reader BoardReader Board
Reader BoardReader Board
Reader Board
Description
The Output Board provides connections for 16 relay outputs. This board can be rack
mounted, in which case, only one edge is accessible for wiring. Mounting the board flat
increases the amount of available I/O slightly but also significantly decreases the number
of boards that can be mounted in one enclosure.
Starting at the bottom of the rack-mount side of the board, the first connector provides
power to the board. The next connector provides communication with the Controller
(PRO22IC). Continuing up this edge, the next 6 connectors provide 12 relay output
connections.
When the board is mounted flat, four additional relay outputs and two dedicated alarm
inputs for cabinet tamper and power fault detection are available on the opposite edge of
theboard.
All 16 form-C relay outputs are designed to handle dry-circuit signals. The two dedicated
inputs are non-supervised. Communication to the control panel is accomplished via an
RS-485interface.This board requires12VDCinput power.
When communication to the Controller is lost, this board maintains all previous output
settings at the time communication was lost.
Set Up
JumperSettings:
repmuJ gnitteS tluafeD detceleS
1J FFO *evitcatonsirotanimretLOE584-SR1troP
NOevitcasirotanimretLOE584-SR1troP

10 PRO-2200 Output Module PRO22OUTInstallation Guide
Dipswitch Settings:
8S 7S 6S 5S 4S 3S 2S 1S NOITCELES
FFOFFOFFOFFONO*1SSERDDA
FFOFFOFFONOFFO2SSERDDA
FFOFFOFFONONO3SSERDDA
FFOFFONOFFOFFO4SSERDDA
FFOFFONOFFONO5SSERDDA
FFOFFONONOFFO6SSERDDA
FFOFFONONONO7SSERDDA
FFONOFFOFFOFFO8SSERDDA
FFOFFO devreseR
FFONO SPB006,9
NOFFO SPB002,91
NONO *SPB004,83
FFO *desUtoN
* = Default