Honeywell CM701 User manual


AUTO
1234567
CM701..................................2-6
CM707................................7-11
USER GUIDE


Features
• Ergonomic user interface featuring an ‘OK-button’.
• Large LCD (Liquid Crystal Display) Screen
with
backlight.
• 4 independent temperature levels (from 5°C to 35°C).
• Automatic Summer/Winter Time Change.
•
Optimum Start to achieve the right temperature at the
right time.
• Built-in Memory holds the user program indefinitely.
Description
The Honeywell CM701 is a
programmable room thermostat
designed to control your heating
system efficiently, providing
comfortable temperatures when
you are at home and energy
savings when you are away. The
following instructions explain how
to program and use the thermostat
to provide the most home comfort
at the least cost.
Controls Layout
LCD Screen
Battery Low Indicator
Time Display
Burner On Indicator
Temperature Display
1
2
3
6 11
12
13
7
8
9
10
4
5
Battery Cover
Program Buttons
Time Change Buttons
Set Date Button
Temperature Change Buttons
Temperature Enquiry Button
Operating Mode Buttons
Green OK Button
Battery Compartment
..4
AUTO
AUTO
MAN
OFF
13
1 2 43 5
7
8
9
6
11
12
10
PROGRAM
CM70
DATE
14
14
CM701 - USER GUIDE


SETTING-UP THE CM701 ‘Getting Started’
This section shows you how to setup and run the thermostat in 3 simple steps:
STEP 1: Installing the Batteries
Note: Please follow the instructions in this section only if the thermostat screen is blank (no
symbols or digits are displayed). If the room temperature is already displayed move on to Step 2:
Setting the Date and Time.
To install the Batteries:
a. Lift up the front cover of the thermostat to reveal the battery cover and product controls.
b. Remove the battery cover by pressing down and sliding out.
c. Insert the 2 x AA LR6 Alkaline Batteries supplied with the thermostat, ensuring the correct
orientation (see ‘Controls Layout’ on page 2).
d. After a short pause the thermostat will display information on the screen and is now ready for use.
e. Replace the battery cover by sliding it firmly back into the front of the thermostat.
STEP 2: Setting the Date and Time
To set the Date and Time:
a. Press the DATE button to begin setting the date. When you set
the date for the first time after the batteries are inserted, the
display will show:
Press the or buttons to set the current day of the month
(e.g. d 01 = 1st day of the month) then press the green
button to confirm.
b. Press the or buttons to set the current month of the
year (e.g. m 01 = January) then press the green button to
confirm.
c. Press the or buttons to set the current year (e.g. yr 06
= 2006) then press the green button to confirm.
The date is now stored.
d. Use the or buttons to set the correct time then press
the green button to confirm. Each press of the buttons will
change the time by one minute and holding them down will
change the time slowly at first and get progressively quicker.
Note: If this mode is entered accidentally then press the
AUTO, MAN or OFF buttons to exit.
STEP 3: Running the Built-in Heating Program
The thermostat is now ready for operation. Press the AUTO button and the built-in heating program
will start running. Note: The built-in heating program has been designed to provide normal comfort
requirements, but if you want to customise the settings please see the next section ‘Programming
the CM701’.
AM

4
Period 1 2 3 4
Time 6:30 8:00 18:00 22:30
Temperature 21°C 18°C 21°C 16°C
The Built-in Heating Program
The built-in heating program has 4 temperature level changes that can be set between 3.00am
and 2.50am the following day - allowing you to maintain the evening temperature after midnight.
Each temperature level can be set between 5°C and 35°C, and adjusted in 0.5°C increments. The
factory default program for heating is as follows.
Reviewing the Heating Program
To review or edit the heating program use the PROGRAM or buttons to navigate between
the 4 individual programming periods.
Modifying the Heating Program
To change the heating program:
a. Press either of the PROGRAM or buttons to
enter the programming mode. The time / temperature
settings for period will be flashing as shown. The
active period is highlighted by a flashing square
around the numbers at the bottom of the screen.
b. To adjust the period start time use the or buttons, the display will stop flashing and the
‘OK?’ indicator will be displayed. Holding the button down will change the time quickly.
Note: If you are pressing the or buttons and the display flashes the next period, it
means the next period will be pushed forward.
c. Once the required time is reached press the green button to confirm.
Note: If the original time setting did not require adjustment press the green button to move
to step ‘d’.
d. The temperature setting for period will now be flashing. To adjust this press the or
buttons and confirm the setting again by pressing the green button.
e. The next time and temperature period will now be active. Adjust this by repeating steps b- d
above until all 4 periods are set or press the AUTO button to run the program as set, at any time.
Disabling / Enabling Time Periods
The thermostat has 4 periods that can be programmed, but you may not need all of these switch
points for your heating requirements. Therefore, any period from 2 to 4 can be removed from (or
returned to) the heating program profile.
To disable or enable time periods:
a. To disable unwanted periods go to the desired period ( to 4) using the PROGRAM or
buttons to navigate, ensure the correct period is highlighted with the flashing square symbol.
Press and hold the button for at least 2 seconds and the display will indicate the period has
been removed from the program.
b. To enable periods again follow the same procedure as above, navigating to the already disabled
period. To enable this period again press and hold the button for at least 2 seconds.
4
‘Efficient Daily Use’ PROGRAMMING THE CM701


Choosing the Operating Mode
The thermostat can operate in three different modes: Automatic, Manual or Off. To set the operating
mode press either of the AUTO, MAN or OFF buttons. The screen indicates which mode is
currently active by displaying AUTO, MAN or OFF.
•
AUTO (automatic) mode sets the thermostat to follow the built-in temperature program (default
or personalised). Operating the thermostat in this mode is the best way to maintain a high level
of temperature comfort whilst maximising your energy savings.
• MAN (manual) mode sets the thermostat to act as a simple thermostat with a fixed setpoint
throughout the day. The setpoint can be adjusted from 5°C to 35°C by using the or buttons.
The thermostat will continue to maintain this temperature until another operating mode or temperature
is selected.
• OFF mode sets the thermostat to control to a minimum temperature setting of 5°C (default) that
acts as a frost protection measure for your home.
During Normal Operation
• Temperature Enquiry
In AUTO, MAN and OFF operating modes the thermostat will display the current room
temperature. To review the programmed ‘target’ temperature (the temperature which the
thermostat is trying to maintain) press the button. This ‘target’ temperature value will be
displayed flashing for 5 seconds before returning to the current room temperature value.
• Temperature Override
During normal operation (AUTO mode) the programmed temperature can be adjusted manually
by pressing the or buttons or the button. The ‘target’ temperature will be displayed and
flash for 5 seconds - during this time the or buttons can be used to modify the set value.
Note: This temperature override is cancelled at the next programmed temperature change.
Adjusting the Time
To adjust only the time during normal operation use the or buttons to adjust the time and
press the green button again to confirm any changes.
OPERATING THE CM701 ‘Using the Features’


Using the Special Features
• Display Backlight
The CM701 has a backlit display that will illuminate when a button is pressed for easier viewing
of the display in low light conditions.
• SERVICE indicator
Note: This option only works if activated by your installer.
The 'SERVICE' indicator is displayed at set intervals
as a reminder that your heating system requires a
routine check. Please call your installer to arrange a
maintenance visit.
The ‘SERVICE’ indicator will remain on the display
of the CM701 until it is either reset or disabled by
your installer. The CM701 and heating system will
continue to operate as normal.
• Automatic Summer/Winter Time Change
The CM701 has a built-in Automatic Summer/Winter Time Change feature that will automatically
adjust the clock forward or backward by one hour for ‘Daylight Saving Time’. This is carried out
on the last Sunday of March and October each year.
• Optimum Start
Optimum Start is a program which ensures that the optimum temperature conditions are
achieved at the required times. This is an Energy Efficiency feature that adjusts the start time
of your heating system depending upon how cold it is. For example, on cold days your heating
system will be started earlier to ensure that your home is warm when you get up (at the target
temperature) and on warmer days the heating system will be started later to save energy. So,
if the Optimum Start Feature is used, then the time / temperature settings which are entered
into the thermostat should be set to when you want to be warm by and not when you want the
heating system to start.
‘Using the Features’ OPERATING THE CM701

7
How do I change the batteries on the
thermostat when they run out?
The thermostat constantly monitors the battery
power level, which typically lasts for about 2
years before needing replaced. When the power
is running low a flashing symbol will be
displayed on the screen. To change the batteries
follow the steps in the above section (‘STEP 1:
Installing the Batteries’ on page 3), replacing
the used batteries with new ones in Step c.
Note: While changing the batteries your program
settings will be stored but you may need to adjust
the time settings to be correct.
FAQ’s
How do I set one temperature for the
whole day?
To operate as a simple thermostat with one
temperature throughout the day, select the
manual operating mode by pressing the
MAN button. Adjust the temperature by
pressing the or buttons - this can be
set anywhere from 5°C to 35°C in 0.5°C steps.
The thermostat will continue to maintain this
temperature until another operating mode is
selected or the temperature is adjusted.
Symptom
Blank Display (Power Loss).
Display shows flashing
symbol.
Display shows symbol.
Display shows the word 'SERVICE'
Remedy
Check batteries are installed by removing the battery
cover.
Check batteries have been installed in the correct
orientation.
Replace the batteries.
The batteries in the thermostat are low on power
- Replace the batteries.
A fault has occurred in your heating system. Remove
and re-insert the batteries.
If the symbol does not clear after a few minutes
contact your installer.
Your installer has set a scheduled maintenance alert
period on your CM701 as a recommendation that your
heating system should receive a routine inspection.
Call your installer to arrange a maintenance visit.
Note: The CM701 and heating system will continue to
operate as normal.
TROUBLESHOOTING THE CM701


CM707 - USER GUIDE
Features
• Ergonomic user interface featuring an ‘OK-button’.
•
Large LCD (Liquid Crystal Display) Screen with backlight.
• 7-day heating program to match your lifestyle, whilst
maximising energy savings.
•
4 independent temperature levels per day (from 5°C to 35°C).
• Holiday button saves energy by letting you reduce the
temperature for 1 to 99 days.
• Automatic Summer/Winter Time Change.
• Optimum Start to achieve the right temperature at the
right time.
• Built-in Memory holds the user program indefinitely.
Description
The Honeywell CM707 is a
programmable room thermostat
designed to control your heating
system efficiently, providing
comfortable temperatures when
you are at home and energy
savings when you are away. The
following instructions explain how
to program and use the thermostat
to provide the most home comfort
at the least cost.
Controls Layout
LCD Screen
Battery Low Indicator
Time Display
Burner On Indicator
Day Indicator
Temperature Display
1
2
3
4
5
6
Holiday Function Button
Program Buttons
Copy Day Button
Set Date/Day Button
Time Change Buttons
Temperature Change Buttons
Temperature Enquiry Button
Operating Mode Buttons
Green OK Button
Battery Compartment
Battery Cover
7
8
9
10
11
12
13
14
15
16
17
COPY
DAY
DATE/
DAY
..4
AUTO
1234567
AUTO
MAN
OFF
16
15
17
1 2 43 5
8
9
10
7
12
13
14
11
6
PROGRAM
CM707


SETTING-UP THE CM707 ‘Getting Started’
This section shows you how to setup and run the thermostat in 3 simple steps:
STEP 1: Installing the Batteries
Note: Please follow the instructions in this section only if the thermostat screen is blank (no
symbols or digits are displayed). If the room temperature is already displayed move on to Step 2:
Setting the Date and Time.
To install the Batteries:
a. Lift up the front cover of the thermostat to reveal the battery cover and product controls.
b. Remove the battery cover by pressing down and sliding out.
c. Insert the 2 x AA LR6 Alkaline Batteries supplied with the thermostat, ensuring the correct
orientation (see ‘Controls Layout’ on page 8).
d. After a short pause the thermostat will display information on the screen and is now ready for use.
e. Replace the battery cover by sliding it firmly back into the front of the thermostat.
STEP 2: Setting the Date and Time
To set the Date and Time:
a. Press the DATE/DAY button to begin setting the date. When
you set the date for the first time after the batteries are inserted,
the display will show:
Press the or buttons to set the current day of the month
(e.g. d 01 = 1st day of the month) then press the green
button to confirm.
b. Press the or buttons to set the current month of the
year (e.g. m 01 = January) then press the green button to
confirm.
c. Press the or buttons to set the current year (e.g. yr 06
= 2006) then press the green button to confirm.
The date is now stored and the Day Indicator will be displayed
under the current day of the week (e.g. 1 = Monday, 2 =
Tuesday, etc.)
d. Use the or buttons to set the correct time then press
the green button to confirm. Each press of the buttons will
change the time by one minute and holding them down will
change the time slowly at first and get progressively quicker.
Note: If this mode is entered accidentally then press the
AUTO, MAN or OFF buttons to exit.
STEP 3: Running the Built-in Heating Program
The thermostat is now ready for operation. Press the AUTO button and the built-in heating program
will start running. Note: The built-in heating program has been designed to provide normal comfort
requirements, but if you want to customise the settings please see the next section ‘Programming
the CM707’.
AM

0
‘Efficient Daily Use’ PROGRAMMING THE CM707
Modifying the Heating Program
To change the heating program:
a. Press either of the PROGRAM or buttons to
enter the programming mode. The time / temperature
settings for period

on Monday (Day 1) will be
flashing as shown. The active period is highlighted by
a flashing square around the numbers at the bottom of
the screen and the selected day is shown with the day
indicator.
b. To adjust the period start time use the or buttons, the ‘OK?’ indicator will be displayed to
confirm the change. Holding the button down will change the time quickly.
Note: If you are pressing the or buttons and the display flashes the next period, it
means the next period will be pushed forward.
c. Once the required time is reached press the green button to confirm.
Note: If the original time setting did not require adjustment press the green button to move
to step ‘d’.
d. The temperature setting for period on Monday (Day 1) will now be flashing. To adjust this
press the or buttons and confirm the setting again by pressing the green button.
e. The next time and temperature period will now be active. Adjust this by repeating steps b - d
above until all 4 periods are set for Monday or press the AUTO button to run the program as
set, at any time.
You now have a choice of how to set the program for the next day:
1234567
4
The Built-in Heating Program
The built-in heating program has 4 temperature level changes per day that can be set between
3.00am and 2.50am the following day - allowing you to maintain the evening temperature after
midnight. Each temperature level can be set between 5°C and 35°C, and adjusted in 0.5°C
increments. The factory default program for heating is as follows.
Reviewing the Heating Program
To review or edit the heating program use the PROGRAM or buttons to navigate between the
4 individual programming periods for that day. Use the DATE/DAY button to step through each day of
the week, so the complete 7 day heating program can be reviewed or edited.
Period 1 2 3 4
Time 6:30 8:00 18:00 22:30
Temperature 21°C 18°C 21°C 16°C
Monday to Friday
(Day 1 to 5)
Period 1 2 3 4
Time 8:00 10:00 18:00 23:00
Temperature 21°C 21°C 21°C 16°C
Saturday & Sunday
(Day 6 & 7)