Honeywell FOCUSPRO TH6320R User manual

FocusPRO®TH6320R
Wireless Thermostat
Termóstato inalámbrico
Thermostat Sans Fil
Operating Manual

® U.S. Registered Trademark. Patents pending.
Copyright © 2008 Honeywell International Inc. All rights reserved.
Read and save these instructions
Quick Reference Card
Grasp and pull to see basic
operating instructions at a
glance.
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
Battery Holder
Press down and pull to
remove batteries.
Batteries should be
replaced once a year
(see page 16).
CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage,
do not operate cooling system when outdoor temperature is below 50°F (10°C).

11
About your new thermostat
Programming at a glance............2
Quick reference to controls ........3
Quick reference to display..........4
Programming & Operation
Set time and day ........................5
Fan settings (auto/on) ................6
System settings (heat/cool)..........7
Program schedules ....................8
Program schedule overrides ....10
Auto-changeover (heat/cool) ....12
Remote control..........................13
Display outdoor climate............14
Find lost remote control............14
Special features ........................15
Appendices
Battery replacement..................16
In case of difficulty....................18
Limited warranty........................19
Regulatory information..............60
Contents Español: vea la página 20 •Français : voir la page 40

2
About your new thermostat
Your new thermostat is pre-programmed and ready to go. All you have to
do is set the time and day. Then check the settings below and change if
needed:
1Set time and day (required for proper operation)...............See page 5
2Select fan setting (Auto/On)....................................................See page 6
3Select system setting (Heat/Cool) .........................................See page 7
4Program schedules: Preset to energy-saving levels
while you’re at work or asleep (assumes you
wake at 6 am, leave at 8 am, return at 6 pm
and go to bed at 10 pm).........................................................See pages 8-9
ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time,
and manually adjust the temperature (see pages 10-11).

3
Quick reference to controls
Digital display (see page 4) Battery holder (see page 16)
Temperature buttons
Press to adjust temperature
settings (see page 10-11)
Hold button
Press to override programmed
temperature control (see page 11)
Function buttons
Press to select the function displayed just above each button.
(Functions change depending on the task.)

Quick reference to display screen
4
System setting
Heat/Cool/Auto/Off/Em
Heat (see page 7)
Fan setting
Auto/On (see page 6)
Current program period
Wake/Leave/Return/Sleep
(see pages 8-9)
Set Clock/Day/Schedule
(see pages 5 & 9)
Current inside temperature
Recovery
(see page 15)
Low battery warnings
(see pages 16-17)
System status
Heat On/Cool On
(If flashing, see p. 15)
Auxiliary heat
(Only for heat pumps
with auxiliary heat)
More
Press to view outdoor climate (if
outdoor sensor is installed), or to
find a misplaced remote control if
installed (see page 14)
Current time/day
(see page 5)
Temperature setting
(see pages 9-11)
Heat OnAux
Indoor Recovery Replace Battery Heat
Setting
75 6:30 AM 75
Set
Clock/Day
Schedule
System
Heat More
°°
Fan
Auto
Wake

5
Set the time and day
1 Press SET CLOCK/DAY/SCHEDULE, then
press or to set clock.
2 Press SET DAY, then press or
to select the day of week.
3 Press DONE to save.
Press SET CLOCK/DAY/SCHEDULE, then adjust time
4:30 PM
Press SET DAY, then select current day
Wed
Done
Set
Day Set Schedule
Set
Clock/Day
Schedule
System
Heat More
Fan
Auto
Note: If the SET CLOCK/DAY/SCHEDULE
option is not displayed, press DONE
or CANCEL.
Note: If the display flashes Set
Clock, the thermostat will follow your
settings for the weekday “Wake”
time period until you reset the time
and day.

6
Select the fan setting
Press FAN to select Auto or On.
In “Auto” mode (the most commonly
used setting), the fan runs only when the
heating or cooling system is on.
If set to “On,” the fan runs continuously.
Set
Clock/Day
Schedule
System
Heat More
Fan
Auto
Set
Clock/Day
Schedule
System
Heat More
Fan
On
Note: Options may vary
depending on your heating/
cooling equipment.

7
Select the system setting
Note: Options may vary
depending on your heating/
cooling equipment.
Press SYSTEM to select:
•Heat: Thermostat controls only the
heating system.
•Cool: Thermostat controls only the
cooling system.
•Off: All systems are off.
•Auto: Thermostat automatically
selects heating or cooling depending
on the indoor temperature.
•Em Heat (only for heat pumps with
auxiliary heat): Thermostat controls
Emergency and Auxiliary Heat.
Compressor is locked out.
Set
Clock/Day
Schedule
System
Heat More
Fan
Auto
Set
Clock/Day
Schedule
System
Cool
More
Fan
Auto

8
EnergyStar®settings for maximum cost savings
This thermostat is pre-set to use EnergyStar®program settings. We recom-
mend these settings, since they can reduce your heating/cooling expenses by
as much as 33%. (See next page to adjust times and temperatures of each
time period.)
70
°
78
°
70
°
78
°
62
°
85
°
62
°
85
°
70
°
78
°
70
°
78
°
62
°
82
°
62
°
82
°
Heat (Mon-Fri) Cool (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun)
Wake
(6:00 am)
Leave
(8:00 am)
Return
(6:00 pm)
Sleep
(10:00 pm)
[Or cancel period]
[Or cancel period]
[Or cancel period]
[Or cancel period]