Honeywell Single Stage Heat Pump ProgrammableCommercial... User manual

® U.S. Registered Trademark
Copyright © 1997 Honeywell Inc. • All Rights Reserved 63-4361
Single Stage Heat Pump Programmable
Commercial Thermostat
GUIDE SPECIFICATION
1.0 GENERAL
1.1 Overview
The contractor shall furnish, install, and place in operating condition an HVAC control system described herein.
All units shall be located in accordance with the plans.
1.2 Type of System
1.2.1 System Requirements
a. Controls one heating and one cooling stages for heat pump applications.
b. Permit seven day programming.
c. Provide two occupied and two unoccupied periods per day.
d. Offer automatic heat/cool changeover with 2°F minimum deadband.
e. Provide override capability for a three hour period.
f. Include a comfort adjust feature to modify setpoints for a three hour period.
g. Provide Proportional plus Integral (P + I) temperature control.
h. Permit automatic or manual changeover between heating and cooling setpoints.
i. Display room temperature in °F or °C.
j. Display time in 12 or 24 hour clock format.
1.2.2 System Components
a. Seven day programmable thermostat.
b. Wallplate.
1.3 Codes and Standards
1.3.1 The system shall comply with applicable provisions of ASHRAE 90-75.
1.3.2 These specifications are based on equipment from Honeywell to set a standard for design and quality.
1.4 Wiring
1.4.1 All wiring meets National Electrical Codes and local electrical codes.
1.5 Testing Guarantee Service
1.5.1 Prior to installation, the contractor shall provide copies of submittals.
1.5.2 The contractor is responsible for assuring that conduit and wire quantity, size, and type are suitable for
the equipment supplied.
1.5.3 Upon completion, the contractor shall conduct a total system test for the owner and engineer.
1.5.4 All components, parts, and assemblies supplied by the manufacturer shall be guaranteed against
defects in materials and workmanship for 12 months. Warranty service shall be performed by the
contractor.

SINGLE STAGE HEAT PUMP PROGRAMMABLE COMMERCIAL THERMOSTAT
63-4361 2
2.0 SEQUENCE OF OPERATIONS
The heating and cooling setpoints shall be individually adjustable for both the occupied and unoccupied periods. The
thermostat shall have a minimum deadband of 2°F (no mechanical heating or cooling shall operate within this
deadband). Space temperature deviation above the cooling setpoint or below the heating setpoint shall generate a
demand signal to control the system as follows.
2.1 Heating
2.1.1 The thermostat shall control the heating output based on the demand signal communicated from the
thermostat program, taking into account both space temperature deviation (proportional error) and the
duration of that temperature deviation (integral error).
2.1.2 The thermostat shall energize heating equipment when space temperature falls below heating
setpoint.
2.2 Cooling
2.2.1 The thermostat shall control the cooling output based on the demand signal communicated from the
thermostat program, taking into account both space temperature deviation (proportional error) and the
duration of that temperature deviation (integral error).
2.2.2 The thermostat shall energize cooling equipment when space temperature exceeds cooling setpoint.
2.3 Heating Setback and Cooling Setup
Initiation of heating setback or cooling setup for each of 7 days shall be provided by a programmed time
schedule manually entered into the thermostat. When all or a portion of a manually programmed schedule is
unavailable, the thermostat shall control to the default program as follows:
Table of Default Program
Occupied Unoccupied
Heating Setpoints 70°F (21°C) 55°F (13°C)
Cooling Setpoints 78°F (26°C) 90°F (32°C)
2.4 Setpoint Recovery from Unoccupied to Occupied
The thermostat shall employ Intelligent Recovery™. This shall select the optimum time to begin building warm
up or cool down based on setpoints and occupied program as follows:
2.4.1 Heating: 5°F per hour.
2.4.2 Cooling: 5°F per hour.
2.5 Fan Operation
2.5.1 Fan operation shall be energized with calls for cooling and calls for heating (optional).
2.6 Heating and Cooling Operation Minimum On and Off Times
The thermostat shall incorporate a program to maintain minimum-stage operation in both the heating and
cooling:
2.6.1 Cooling: 2 minutes on and 4 minutes off.
2.6.2 Heating: 2 minutes on and 4 minutes off.
2.7 Power Interruption
The system shall cycle off and provide timed restaging of heating or cooling equipment upon restoration of
power. The restaging operation shall occur according to minimum stage operation times incorporated in the
thermostat. A power interruption is annunciated by a blank LCD display.
2.7.1 During a power interruption less than 2 hours, the thermostat retains all programmed occupied and
unoccupied start times and temperatures as well as the present time and day.

SINGLE STAGE HEAT PUMP PROGRAMMABLE COMMERCIAL THERMOSTAT
3 63-4361
2.7.2 During a power interruption greater than 2 hours, the thermostat retains all programmed occupied and
unoccupied start times and temperatures. Only the present time and day will need to be
reprogrammed.
2.8 Calibration
2.8.1 No calibration and no adjustment shall be required for mixed air temperature, throttling range, reset
ratio, band width, or discharge air temperature.
2.8.2 Temperature setting displayed on thermostat shall be adjustable within ±3°F of measured room
temperature (optional).
2.9 Security
Two levels of security shall exist:
2.9.1 A keypad lockout switch located on the back of the thermostat shall allow for three types of keypad
lockout.
a. Lock out all keys on the thermostat.
b. Lock out all keys on the thermostat except System and Fan settings, temporary setpoint
adjustments, and clock and day adjustments.
c. Lock out thermostat Installer Setup only.
2.9.2 Thermostat shall allow for door to be locked by use of two Allen head screws to lock the cover and not
allow access to the keypad.
2.10 Overrides
Temperature setpoints can be overridden in three ways:
2.10.1 Thermostat shall allow for a 3 hour timed override from unoccupied setpoint to occupied setpoint from
the thermostat keypad.
2.10.2 Thermostat shall allow for a 3 hour timed adjustment of the occupied setpoint from the thermostat
keypad.
2.10.3 Thermostat shall allow for a continuous override to the unoccupied setpoint from the thermostat
keypad.
3.0 MAJOR EQUIPMENT
Model
Number Description Features
T7200E2005 Commercial programmable
thermostat, taupe color. • 7-day programming • 2 occupied and 2 unoccupied periods per day
• System and fan setting key set to AUTO only
• Wallplate included
4.0 OPTIONS
4.1 System Accessories
4.1.1 T675A—Remote Bulb Temperature Control, low ambient compressor lockout.
4.1.2 R8222—Switching Relay.
4.1.3 W950—Status Panels.

Home and Building Control Home and Building Control Helping You Control Your World®
Honeywell Inc. Honeywell Limited-Honeywell Limitée
Honeywell Plaza 155 Gordon Baker Road
P. O. Box 524 North York, Ontario
Minneapolis, MN 55408-0524 M2H 2C9
63-4361 J.A. 2-97
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.