Honeywell WebStat T7350 Owner's manual

63-2604
® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc.
All Rights Reserved
T7350
Programmable Thermostat
FOR CONVENTIONAL/HEAT PUMP SYSTEMS
Contents
Features ........................................................................... 2
Settings ............................................................................ 3
Programming ................................................................... 5

2 63-2604
FEATURES
• Typically used in buildings (including:
restaurants, shopping malls, office
buildings and banks) under 55,000
square feet.
• For single zone rooftop units, split
systems, heat pumps or hot/chilled water
systems.
• 7-day programming.
• Two Occupied and two Not Occupied
periods per day.
• Keypad multi-level lockout available with
all models.
• Individual heat and cool setpoints
available for Occupied and Not Occupied
periods.
• Convenient overrides allow temporary
setpoint changes.
• Intelligent Fan™ feature energizes fan
continuously in the Occupied periods. Fan
can also be configured for conventional
heat or electric heat fan operation.
• Remote sensor capability for temperature
(including outdoor air and discharge air)
and humidity sensors.
• P+I+D control minimizes temperature
fluctuations.
• Recovery ramping control automatically
optimizes equipment start times based
on building load.
• Thermostat Interface Module (TIM)
connections to thermostat from PDA for
advanced configuration, programming,
etc.
• Universal Versaguard™ Thermostat
guards available.

3 63-2604
• Auxiliary subbase contact typically
interface with a Honeywell Economizer
System (for total rooftop control
integration) or act as dehumidification
output.
Features Available via PDA
Configuration
• 365 day clock with holiday programming.
• Automatic Daylight Saving Time
adjustments.
• Selectable dehumidification limit control.
• Modulating output configuration.
• Occupancy input to control standby
setpoint.
• Additional standby period used in low
traffic areas.
• Sequential start option.
• Discharge air high/low limits.
• Selectable recovery ramp.
• Ambient lockout (with outdoor sensor).
SETTINGS
Using Thermostat Keys
The thermostat keys are used to:
• set current time and day,
• program times and setpoints for heating and
cooling,
• override the program temperatures,
• display present setting,
• set system and fan operation,
• perform simple configuration.
NOTE: See Fig. 1 for keypad information.
Setting Temperature
Refer to Table 1 for default temperature
setpoints. See Programming section for
complete instructions on changing these.

4 63-2604
Table 1. Default Setpoints.
Setting System and Fan
System default setting is Auto. The fan default
is set so the fan operates continuously during:
— Occupied periods,
— Heating and cooling equipment stages in
Not Occupied and recovery periods.
NOTE: Use System and Fan keys to change
settings.
System Settings
— Auto: Thermostat automatically changes
between heating and cooling based on
sensed indoor temperature.
— Cool: Thermostat controls cooling.
— Off: Heating, cooling, and fan are all off.
— Heat: Thermostat controls heating.
— Em Heat: Auxiliary heat serves as first stage.
Compressor stages are locked off.
Fan Settings
— On: Fan operates continuously in occupied
and standby periods. Fan cycles with call for
heat or cool during not occupied periods.
— Auto: Fan cycles with call for heating or
cooling during occupied, standby, and
not occupied periods.
NOTE: This is further modified by selection of
conventional or electric heat.
Control Occupied Not Occupied Standby
Heating 70°F (21°C) 55°F (13°C) 67°F (19°C)
Cooling 75°F (24°C) 85°F (29°C) 78°F (26°C)

5 63-2604
PROGRAMMING
The thermostat operates at the Occupied
temperature setting unless the thermostat is
programmed. The program has four settings:
— Occupied heat.
— Occupied cool.
— Not Occupied heat.
— Not Occupied cool.
The thermostat can be set for two Occupied
and two Not Occupied times for each day of the
week (28 independent time settings). The
Temporary Occupied key provides quick
setpoint changes for increased comfort during
Not Occupied periods. The Temporary Not
Occupied key provides energy efficient
operation for extended periods of time.
IMPORTANT
Programming the thermostat with the
keypad requires 24 Vac (turn on
system power). The keyboard lockout
feature must be disabled.
NOTE: Before starting programming, use
Table 2 to organize the program
schedule.
Setting Current Day/Time
This can be done using the keypad.
IMPORTANT
Once you set the day/time once, you
should not need to set it again. As a
result, if you use a PDA to set the day
based upon the calendar (MM/DD/
YYYY), the device will not allow the
keypad to change the day.

6 63-2604
Table 2. Occupied and Not Occupied Period Start Times.
NOTE: 12:00 PM is Noon, and 12:00 AM is Midnight.
Day Occupied Period 1 Not Occupied Period 1 Occupied Period 2 Not Occupied Period 2
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday

7 63-2604
Fig. 1. Thermostat key locations.
When using the keypad to change the day/time:
1. Press Set Day until the current day is
displayed.
NOTE: Sun = Sunday, Mon = Monday,
Tue = Tuesday,
Wed = Wednesday,
Thu = Thursday, Fri = Friday,
Sat = Saturday.
2. Press Set Time.
3. Press up ▲ or down ▼until the current
time is displayed.
NOTE: Tapping Set Time changes the
time in one hour increments.
4. Press Run Schedule.
System Fan Run
Schedule
CopyNot OccupiedOccupiedDay
Clear
Start Time
Day Time
Temperature
Temporary
Occupied
Override
HEAT HEATCOOL COOL
HEAT COOL ON AUTO
Schedule
Set Day/Time
Occupied Not Occupied
Temporar y
Not Occupied
M19610BB

8 63-2604
Setting Schedule Times
Use the keys in the “Schedule” area of the
keypad for this procedure.
1. Press Occupied.
NOTE: Anytime a start time is not
required, press Clear Start Time.
2. Press Day until desired day is displayed.
3. Press Occupied or Not Occupied until the
proper period is displayed.
4. Press up ▲ or down ▼until the
desired start time is displayed.
5. Repeat steps 3 and 4 for a given day.
6. Repeat steps 2 through 5 until finished.
Copying a Day
Use the keys in the “Schedule” area of the
keypad for this procedure.
NOTE: The thermostat must be in program
mode to use the copy feature. If the
thermostat is already in program
mode, skip step 1.
1. Press Occupied.
2. Press Day to select the day to be copied.
3. Press Copy.
4. Press Copy again.
5. Press Day until the day to receive the
copy is displayed.
6. Press Copy.
NOTE: DONE displays for two seconds
then the program display
reappears.
7. Repeat steps 2 through 6 for all the days
desired.
8. Press Run Schedule.

9 63-2604
Clearing Program Start Times
1. Press Occupied or Not Occupied until the
start period to be cleared is displayed.
2. Press Day until desired day is displayed.
3. Press Clear Start Time.
4. Repeat steps 1 through 3 for all the start
times to be cleared.
5. Press Run Schedule.
Temperature Setpoints
Setpoint Limits
The setpoint temperature range is 40°F to 90°F
(4°C to 32°C) for heating and 45°F to 99°F
(7°C to 37°C) for cooling.
NOTES: The ranges mentioned can be limited
based upon setpoints and stops:
1. The greater of the Minimum Heat
Stop and the Not Occupied Heat set-
points determines the lowest setting
to which the occupied heat setpoint
can be adjusted: Stop/NotOcc ≤
OccHeat ≤ (OccCool - 2).
2. The lesser of Maximum Cool Stop
and Not Occupied Cool setpoints
determines the highest setting to
which the occupied cool setpoint can
be adjusted: Stop/NotOcc ≥OccCool
≥(OccHeat + 2).
3. The Maximum Occupied Heat Set-
point is limited by Occupied Cool
Setpoint – 2.
4. The Minimum Occupied Cool Set-
point is limited by the Occupied Heat
Setpoint + 2.

10 63-2604
Programming Temperature Setpoints
1. Press Occupied Heat.
2. Press up ▲ or down ▼until the
desired temperature is displayed.
3. Press Occupied Cool.
4. Press up ▲ or down ▼until the
desired temperature is displayed.
5. Press Not Occupied Heat.
6. Press up ▲ or down ▼until the
desired temperature is displayed.
7. Press Not Occupied Cool.
8. Press up ▲ or down ▼until the
desired temperature is displayed.
9. Press Run Schedule.
Temperature Setpoint Overrides
IMPORTANT
— Setup determines Occupied override
duration.
— Default duration is three hours.
NOTE: To cancel Override and immediately
return to the program, press Run
Schedule.
T7770 Setpoint Knob
A T7770 setpoint knob can remotely adjust the
T7350 setpoint. This adjustment can be made
when the sensor is in override.
NOTES:
— During override, only occupied and
standby heat setpoints, and cool
setpoints are adjusted.
— The maximum adjustment is ±5°F.