Honeywell TB7100A1000 - MultiPro Commercial Thermostat User manual

INSTALLATION INSTRUCTIONS
62-0273-05
TB7100A1000 MultiPRO™
Multispeed and Multipurpose Thermostat
APPLICATION
The TB7100A1000 MultiPRO™ Multispeed and Multipurpose Thermostat provides electronic control of 24 Vac heating
and cooling systems.
See Table 1 for a description.
Table 1. TB7100A Thermostat Description.
MERCURY NOTICE
If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash. Dispose of properly.
Contact your local waste management authority
for instructions regarding recycling and the
proper disposal of an old control.
INSTALLATION
When Installing this Product...
1. Read these instructions carefully. Failure to follow
them could damage the product or cause a
hazardous condition.
2. Check ratings given in instructions and on the
product to ensure the product is suitable for your
application.
3. Installer must be a trained, experienced service
technician.
4. After installation is complete, check out product
operation as provided in these instructions.
Feature Description
Powering Methods •Battery only
•24 Vac only
•24 Vac with battery backup
System Types •Conventional (1 Heat, 1 Cool stages)
•Heat Pump (up to 2 Heat,1 Cool stages)
•2 Pipe Fan Coil
•2 Pipe Fan Coil with Auxiliary Heat
•4 Pipe Fan Coil
•PTAC (up to 2 Heat, 1 Cool)
Changeover Manual or automatic changeover selectable
System Setting Heat-Off-Cool-Auto
Fan Setting Auto, On
Fan Speeds Low, Medium, High
Remote Setback Remote Setback Input for occupancy sensor or DDC setback
Fan Ramping
Algorithm
VersaSpeed™ Fan Ramping Algorithm for automatic fan speed selection (fan coil and PTAC
applications)

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
62-0273—05 2
CAUTION
Electrical Shock or Equipment Damage
Hazard.
Can shock individuals or short equipment
circuitry.
Disconnect power supply before installation.
Select Thermostat Location
Select a location for the thermostat about 5 ft (1.5m)
above the floor in an area with good air circulation at
average temperature. See Fig. 1.
Fig. 1. Select thermostat location.
Do not install the thermostat where it can be affected by:
— Drafts or dead spots behind doors and in corners.
— Hot or cold air from ducts.
— Radiant heat from sun or appliances.
— Concealed pipes and chimneys.
— Unheated (uncooled) areas such as an outside wall
behind the thermostat.
Separate Wallplate from Thermostat
1. Separate the wallplate from the thermostat. See
Fig. 2.
Fig. 2. Separate wallplate from thermostat.
Install Wallplate (See Fig. 3)
Mount the thermostat horizontally on the wall:
1. Pull the wires through the wire hole on the wallplate.
2. Position the wallplate on the wall with the arrow
pointing up. Level the wallplate for appearance only.
3. Use a pencil to mark the mounting holes.
4. Remove the wallplate from the wall and drill two
3/16 in. holes in the wall (if drywall) as marked. For
firmer material such as plaster, drill two 7/32 in.
holes. Tap the wall anchors (provided) into the
drilled holes until flush with the wall.
5. Pull the wires through the wire hole on the wallplate
and position the wallplate over the wall anchors.
6. Insert the mounting screws into the wall anchors
and tighten.
Fig. 3. Install wallplate.
WIRING
IMPORTANT
— All wiring must agree with applicable codes,
ordinances and regulations.
— Use 18 gauge thermostat wire. Shielded cable is
not required.
NOTES:
— Sensor wires must have a cable separate
from the thermostat control cable.
— Refer to Table 2 for terminal designation
descriptions.
— See Fig. 6 through 17 for wiring diagrams for
specific equipment applications.
1. Select set of terminal identifications that correspond
to your system type (conventional or heat pump).
(See Fig. 4).
Fig. 4. Terminal identifications for system type.
2. Loosen screw terminals used for the application.
3. Insert the wires into the terminal block and tighten
each screw terminal.
4. Push excess wire back into the wall opening and
restrict wires to the shaded area. See Fig. 5.
5. Plug the wall opening with nonflammable insulation
to prevent drafts from affecting the thermostat.
5 FEET
[1.5 METERS]
YES
NO
M22258
NO
NO
THERMOSTAT
WIRE HOLE
M22267
WALLPLATE
M22268
DRILLED
HOLES (2)
WALL
ANCHORS (2)
MOUNTING
SCREWS (2)
WALLPLATE
M27415
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
SC
REW
TERMINALS

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
3 62-0273—05
Fig. 5. Restrict wires to shaded area of wire hole.
Table 2. Terminal Designation Descriptions.
NOTES:
1. When used in a single-transformer system,
leave metal jumper wire in place between RC
and R. If used on a two-transformer system,
remove metal jumper wire between RC and R.
2. Common wire is optional when thermostat is
used with batteries. When using separate
transformers for heating and cooling, the
common must come from the cooling
transformer.
3. If thermostat is configured for a heat pump in
the Installer Setup, configure changeover
valve for cool (O-factory setting) or heat (B).
4. Sensor wires must have a cable separate
from the thermostat control cable.
Table 3. Wiring Diagrams.
WALLPLATE
M22266
WALL OPENING
WIRE
SHADED AREA
Terminal Designation Description
RC (see Note 1) Power for cooling—connect to secondary side of cooling system transformer.
R (see Note 1) Power for heating—connect to secondary side of heating system transformer.
Y Compressor output.
C (see Note 2) Common wire from secondary side of cooling system transformer.
W1 Heat relay. Auxiliary heat relay to heat pump, PTAC.
G Fan relay. Low fan speed for Fan Coil and PTAC applications.
G2 Fan relay. Medium fan speed for Fan Coil applications only.
G3 Fan relay. High fan speed for Fan Coil and PTAC applications.
O/B (see Note 3) Changeover valve for heat pumps.
S1 (see Note 4) Indoor remote sensor, remote setback, or changeover input.
S2 (see Note 4) Indoor remote sensor, remote setback, or changeover input.
System Type
Wiring Diagram
Figure
Standard Heat/Cool (1H/1C) 6, 7
Heat Only 8
Heat Only with Fan 9
Cool only 10
Heat Pump (No Auxiliary Heat)
(1H/1C)
11
Heat Pump (with Auxiliary Heat)
(2H/1C)
12
4 Pipe Fan Coil 13
2 Pipe Fan Coil (with Auxiliary Heat) 14
2 Pipe Fan Coil (no Auxiliary Heat) 15
PTAC 1H/1C (High speed, Low speed
fan)
16
PTAC 2H/1C (High speed, Low speed
fan)
17
Multiple TR21 Sensors 18, 19, 20
Multiple C7189U Sensors 21

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
62-0273—05 4
Conventional System Wiring
Fig. 6. Typical wiring of single transformer
1H/1C system.
Fig. 7. Typical hookup of dual transformer
1H/1C system.
Fig. 8. Typical hookup of heat-only system.
Fig. 9. Typical hookup of heat-only system with fan.
Fig. 10. Typical hookup of cool-only system.
COMPRESSOR CONTACTOR INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK
FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION
IS OPTIONAL.
1
2
3
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
2
3
L1
(HOT)
L2
1
24 VAC
M27416
HEAT RELAY
COMPRESSOR CONTACTOR
M27417
HEAT RELAY
FAN RELAY
COOLING
TRANSFORMER
HEATING
TRANSFORMER
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
REMOVE FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION
IS OPTIONAL. WHEN USED, THE COMMON MUST CONNECT
TO THE COOLING TRANSFORMER SECONDARY.
1
3
2
3
L1
(HOT)
L2
1
24 VAC
L1
(HOT)
L2
1
24 VAC
C
G
Y
O/B
RC
R
2
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK
W1
G2
G3
S1
S2
M27418
HEAT RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION IS
OPTIONAL.
1
2
3
L1
(HOT)
L2
1
24 VAC
C
G
Y
O/B
RC
R
2
W1
G2
G3
S1
S2
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK
3
M27419
HEAT RELAY
FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION
IS OPTIONAL.
1
2
3
3
L1
(HOT)
L2
1
24 VAC
2
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK
M27420
FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION
IS OPTIONAL.
1
3
2
3
COMPRESSOR CONTACTOR
L1
(HOT)
L2
1
24 VAC
2
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
5 62-0273—05
Heat Pump System Wiring
Fig. 11. Typical hookup of single-stage heat pump
with no auxiliary heat (1H/1C).
Fig. 12. Typical hookup of single-stage heat pump
with auxiliary heat (2H/1C).
Fan Coil System Wiring
Fig. 13. Typical wiring of 4 pipe fan coil.
Fig. 14. Typical wiring of 2 pipe fan coil with reheat.
Fig. 15. Typical wiring of 2 pipe fan coil without
reheat.
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK
COMPRESSOR CONTACTOR
M27421
CHANGEOVER VALVE
1
2
3
4
5
FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION IS
OPTIONAL.
"O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B" IN THE
INSTALLER SETUP.
OPTIONAL INDOOR REMOTE SENSOR OR REMOTE SETBACK.
WIRES MUST HAVE A CABLE SEPARATE FROM THE THERMOSTAT
CABLE.
3
L
1
(HOT)
L2
1
24 VAC
5
C
G
Y
O/B
RC
R
4
2
W1
G2
G3
S1
S2
COMPRESSOR CONTACTOR
M27422
CHANGEOVER VALVE
1
2
3
4
5
FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION
IS OPTIONAL.
"O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B"
IN THE INSTALLER SETUP.
OPTIONAL INDOOR REMOTE SENSOR OR REMOTE SETBACK.
WIRES MUST HAVE A CABLE SEPARATE FROM THE THERMOSTAT
CABLE.
3
L
1
(HOT)
L2
1
24 VAC
AUXILIARY HEAT RELAY
4
2
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK 5
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
COOLING RELAY INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK
HEAT RELAY
LOW FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION IS
OPTIONAL.
1
2
3
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
2
3
L1
(HOT)
L2
1
24 VAC
M27423
HIGH FAN RELAY
MEDIUM FAN RELAY
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK/CHANGEOVER
PIPE SENSOR
TWO PIPE HEAT/COOL RELAY
LOW FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION IS
OPTIONAL.
1
2
3
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
2
3
L1
(HOT)
L2
1
24 VAC
M27424
HIGH FAN RELAY
AUXILIARY HEAT RELAY
MEDIUM FAN RELAY
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK/CHANGEOVER
PIPE SENSOR
TWO PIPE HEAT/COOL RELAY
LOW FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION IS
OPTIONAL.
1
2
3
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
2
3
L1
(HOT)
L2
1
24 VAC
M27425
HIGH FAN RELAY
MEDIUM FAN RELAY

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
62-0273—05 6
PTAC System Wiring
Fig. 16. Typical hookup of PTAC with HI and LO fan
speeds (1H/1C).
Fig. 17. Typical hookup of PTAC with HI and LO fan
speeds (2H/1C).
Sensor Wiring for Temperature Averaging
Fig. 18. Wiring four TR21 (20K ohm) Sensors.
Fig. 19. Wiring two TR21-A (10K ohm) Sensors to
provide a temperature averaging network.
Fig. 20. Wiring two TR21 (20K ohm) Sensors and one
TR21-A (10K ohm) Sensor to provide a temperature
averaging network
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK
COMPRESSOR CONTACTOR
M27426
CHANGEOVER VALVE
1
2
3
4
5
LOW FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION IS
OPTIONAL.
"O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B" IN THE
INSTALLER SETUP.
OPTIONAL INDOOR REMOTE SENSOR OR REMOTE SETBACK.
WIRES MUST HAVE A CABLE SEPARATE FROM THE THERMOSTAT
CABLE.
3
L1
(HOT)
L2
1
24 VAC
5
C
G
Y
O/B
RC
R
4
2
W1
G2
G3
S1
S2
HIGH FAN RELAY
COMPRESSOR CONTACTOR
M27427
CHANGEOVER VALVE
1
2
3
4
5
LOW FAN RELAY
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
FACTORY INSTALLED JUMPER.
WHEN USING BATTERIES, THE 24V COMMON CONNECTION IS
OPTIONAL.
"O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B"
IN THE INSTALLER SETUP.
OPTIONAL INDOOR REMOTE SENSOR OR REMOTE SETBACK.
WIRES MUST HAVE A CABLE SEPARATE FROM THE THERMOSTAT
CABLE.
3
L
1
(HOT)
L2
1
24 VAC
AUXILIARY HEAT RELAY
4
2
INDOOR TEMPERATURE
SENSOR/REMOTE
SETBACK 5
C
G
Y
O/B
RC
R
W1
G2
G3
S1
S2
HIGH FAN RELAY
M27481
S1 S2
T T
SUBBASE
TR21
T T
TR21
T T
TR21
T T
TR21
M27482
S1 S2
SUBBASE
TR21-A
T4 T3
TR21-A
T4 T3
1
11
THE TR21-A IS A 10K OHM SENSOR.
M27483
T4 T3
TR21-A
1
1
THE TR21-A IS A 10K OHM SENSOR.
S1 S2
TT
SUBBASE
TR21
TT
TR21

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
7 62-0273—05
Fig. 21. Wiring four C7189U (10K ohm) Sensors to
provide a temperature averaging network.
POWER THE THERMOSTAT
You can choose from three methods to power the
thermostat:
• Batteries only (AA alkaline).
• 24 Vac direct connection only.
• 24 Vac direct connection with battery backup (AA
alkaline).
Wiring 24 Vac Common
• Single-Transformer System—Connect the common
side of the transformer to the C screw terminal of the
thermostat wallplate. Leave the metal jumper wire in
place between RC and R.
• Two-Transformer System—Connect the common side
of the cooling transformer to the C screw terminal of
the thermostat wallplate. Remove the metal jumper
wire between RC and R.
Installing Batteries
1. Install two AA alkaline batteries on the back of the
thermostat as marked. See Fig. 22.
Fig. 22. Installing batteries.
2. Locate and remove the tab labeled Remove. See
Fig. 23.
IMPORTANT
This tab must be removed in order to set the
real-time clock.
Fig. 23. Remove tab labeled REMOVE from thermostat
back.
Mount Thermostat to Wallplate
1. Align the terminal screw blocks with the pins on the
back of the thermostat.
2. Push the thermostat straight onto the wallplate until
it snaps into place. See Fig. 24.
Fig. 24. Mount thermostat to wallplate.
M27432
WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE.
1
1 C7189 C7189
C7189 C7189
SUBBASE
S1 S2
M22259
BACK OF THERMOSTAT
BATTERY HOLDER
BATTERIES (2)
REMOVE
TAB
REMOVE DURING
INSTALLATION
M22260
REMOVE DURING
INSTALLATION
WALL
M23024

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
62-0273—05 8
SETTING CALENDAR AND TIME
This thermostat is designed to, under normal use,
automatically keep current time and day in memory for up
to ten years once the calendar is set. There are two ways
to set the calendar and time for this thermostat:
SETTING DATE/TIME WHEN THERMOSTAT IS FIRST POWERED
When the thermostat is first powered, the display is ready
to set the calendar and time. The thermostat proceeds
through a sequence of setup screens. See Fig. 25.
SETTING DATE/TIME AFTER THERMOSTAT IS ALREADY
FUNCTIONING
Use the installer setup to set year, month and day. See
the Installer Setup Numbers, Settings, and Tests section.
Fig. 25. Setting calendar and time after initial powerup.
ADVANCED SETTINGS
The thermostat has advanced settings to match the HVAC
system. These settings can be adjusted to match specific
needs. See the following section (Installer Setup
Numbers, Settings, and Tests) for details.
M23023A
MONTH
YEAR DAY
GO BACK KEY
GOES BACK TO
LAST SETTING
NEXT KEY
ADVANCE TO NEXT SETTING
DONE KEY
ADVANCES TO TIME SETTING
SCREEN AND HOME SCREEN
UP AND DOWN KEYS
CHANGES MONTH, DAY,
YEAR AND TIME
DeSelect Day
System & Fan
FanUseEdit
Schedule
View
Clock & More
Tue
Done
PM

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
9 62-0273—05
INSTALLER SETUP NUMBERS, SETTINGS, AND TESTS (TABLE 4)
Configure Installer Setup
1. Press and release the System key.
2. Press System and Done keys simultaneously.
3. Hold keys for approximately five seconds, until the
screen changes.
4. When the display changes, release the System and
Done keys.
NOTE: See Table 4 for installer setup (ISU) numbers
and settings.
Installer System Tests
Use the Installer System Test section to test the heating,
cooling and fan. Refer to the latter portion of Table 4.
CAUTION
Equipment Damage Hazard.
Minimum compressor off time is bypassed
during Installer System Test
Avoid cycling compressor quickly.
IMPORTANT
Use Installer System Test to test heating, cooling
and fan. The setting chosen for System Type
(Installer Setup Number 0170) can prevent some
System Test Numbers from appearing.
Table 4. Installer Setup Menu.
Installer
Setup
Number
Installer Setup
Name
Default
Setting All Settings Notes
0120 Date (Year Upper) 20 20—21 Available year range: 2001 - 2178
0130 Date (Year Lower) 08 00-99 Available year range: 2001 - 2178
0140 Date (Month) 6 1-12
0150 Date (Day) 15 1-31 (Month Dependent)
0160 Schedule Options 4 0—Non-Programmable
4—Programmable
0170 System Selection 1 1—1H/1C Conv
2—1H w/o fan
3—1H with fan
4—1C
5—1H/1C HP
6—2H/1C HP
7—4 pipe Fan Coil
8—2 pipe Fan Coil
9—2 pipe Fan Coil w/ Aux
Heat
10—PTAC 1H/1C (Hi
speed, Lo speed Fan)
11—PTAC 2H/1C (Hi
speed, Lo speed Fan)
Relay Y is used for 2 pipe fan coil output relay.
0180 Heat Fan Operation 0 0—Fossil
1—Electric
Only shows up if conventional system with heat
stages and fan capability is selected (ISU 0170). If
heat pump is selected, fan defaults to electric. If
fan coil or PTAC modes are selected, fan defaults
to electric (does not show up).
0185 Pre-occupancy
Purge Duration
0 0—no duration
1—one hour
2—two hours
3—three hours
Shown only if system has fan and schedule is
programmable (ISU 0160).
Pre-occupancy purge is enabled by a nonzero
duration.
0190 Reversing Valve
O/B
0 0—O (O/B On Cool)
1—B (O/B On Heat)
Only shown if heat pump or PTAC system is
selected.
0220 Cycles Per Hour
(CPH) for first stage
cooling/compressor
3 1-6 Only shown if system has cool stages (ISU 0170).
Shown for heat pump, fan coil, PTAC, and
conventional cooling stages.
0240 CPH for first stage
heat
5 1-12 Only shown if system is conventional with heat
stages, 4 pipe fan coil, 2 pipe fan coil (ISU 0170).
0270 CPH for Em Heat 9 1-12 Only shown if HP with reheat, 2 pipe fan coil with
reheat, and PTAC with reheat (ISU 0170).
0280 Continuous
Backlight
0 0—No
1—Yes
Always shown; however, if AC power is not
present, the option is overridden and normal
backlight operation occurs.

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT
62-0273—05 10
0300 Changeover 1 0—Manual
1—Auto
Only shown if system has both heat and cool
stages (ISU 0170). Shown for CNV, HP, PTAC and
4 pipe fan coil (ISU 0170). Not shown for 2 pipe
fan coil modes.
0310 Deadband 3°F
(2°C)
2 (1.5)—2°F (1.5°C)
3 (2.0)—3°F (2.0°C)
4 (2.5)—4°F (2.5°C)
5 (3.0)—5°F (3.0°C)
6 (3.5)—6°F (3.5°C)
7 (4.0)—7°F (4.0°C)
8 (4.5)—8°F (4.5°C)
9 (5.0)—9°F (5.0°C)
Only shown if Automatic Changeover selected
(ISU 0300).
0320 Temperature
Indication Scale
0 0—°F
1—°C
0330 Daylight Saving 1 0—Disabled
1—Enabled (US)
0340 Remote Temp
Sensor/Remote
Setback/
Changeover Input
0 0—None
1—Remote 10K Indoor
2—Remote 20K Indoor
3—Changeover 2 pipe
Fan Coil modes only
4—Changeover 2 pipe
Fan Coil modes only
Only shown on models that offer remote sensing.
NO input (default mode is Heat)
NO input (default mode is Cool)
0340
(Non-
program
mable)
Remote Temp
Sensor/Remote
Setback/
Changeover Input
0 0—None
1—Remote 10K Indoor
2—Remote 20K Indoor
3—Changeover 2 pipe
Fan Coil modes only
4—Changeover 2 pipe
Fan Coil modes only
5—Remote Setback
6—Remote Setback
Only shown on models that offer remote sensing.
NO input (default mode is Heat)
NO input (default mode is Cool)
Hotel card NO, with 1 second software delay going
from UnOcc to Occupied; 2 minute delay going
from Occupied to UnOcc.
Hotel Card NC, with 1 second software delay
going from UnOcc to Occupied; 2 minute delay
going from Occupied to UnOcc.
0341 Delay for Remote
Setback
0 0—No Delay
2—2 Minute Delay
Only shown if Remote Setback (ISU 0340) is
enabled.
0342 Override Option
(only available in
non-programmable
mode)
0 0—No Override
1—Override
This option is only available for non-programmable
mode (ISU 0160)
0343 Unoccupied
Heating Setpoint
(only when remote
setback enabled)
60°F 50-65°F
10-18°C
0346 Unoccupied
Cooling Setpoint
(only when remote
setback is enabled)
80°F 75-90°F
24-30°C
0347 Fan Ramping 1 0—Disabled (Lo, Med, Hi)
1—Enabled
To enable the fan ramping algorithm. Only
available for fan coil or PTAC applications.
0348 Fan Mode 0 0—User can choose
Cycle or Constant 3
speed: Low->Med->
H i g h - > A u t o - > L o w
1—Cycle Only - Auto only
To select a particular fan mode: Auto is the fan
ramp mode. If ramping is not selected, fan mode
automatically defaults to Low Med High (Constant
only) and ISU 0348 is unavailable. Only available
for fan coil or PTAC applications.
Table 4. Installer Setup Menu. (Continued)
Installer
Setup
Number
Installer Setup
Name
Default
Setting All Settings Notes