Honeywell VisionPRO Wi-Fi TH8320WF Instruction Manual

Doc ID - 1188 • Rev 04 1 / 8
Honeywell WiFi Thermostat
Integration Release Notes
Content
Introduction...1
Installing the Honeywell thermostat...2
Registering the thermostat...3
Enabling auto mode...3
Configuring in Fusion...4
Configuring rules with TCC thermostats...6
Contact information...8
Last modified: 05/03/18
Introduction
The Honeywell WiFi thermostats are a series of WiFi thermostats that have been
tested and certified for integration with the ClareHome system.
When integrating a Honeywell WiFi thermostat into your ClareHome project, no
extra connections are necessary. Install the thermostat according to the
Honeywell documentation, register the thermostat on the Honeywell portal,
enable auto mode in the thermostat, and then connect it to the network using IP.
All HVAC integrations share a common UI, so that the user experience is
consistent. Temperature settings can be controlled via events. Use Fusion’s
Scenes and Rules to automate the actions your customers want.
Supported models:
TH9320WF
TH8320WF
TH8321WF
RTH-8580WF
RTH9580WF
RTH6580WF
TH6320WF1005/B

Doc ID - 1188 • Rev 04 2 / 8
The Following figure shows the Honeywell controls on the ClareHome UI.
Figure 1: User interface of the Honeywell WiFi thermostat.
(1) Change the Heat set point by sliding the indicator around the dial.
(2) Change the Cool set point by sliding the indicator around the dial.
(3) Temperature setting displays on the ClareHome UI in Fahrenheit.
(4) Change the Operation mode using the slider control.
(5) Change the Fan mode using the slider control.
Installing the Honeywell thermostat
A qualified HVAC installation technician should install the Honeywell thermostat.
Refer to the documentation that came with the thermostat for detailed installation
instructions. Clare Controls does not assume any responsibility for damages
caused by improper installation or connection to the data network.

Doc ID - 1188 • Rev 04 3 / 8
Registering the thermostat
After installation, you must register the thermostat on the Honeywell portal. This
allows the thermostat to be accessed remotely and updated with information from
the Honeywell portal
To register the Honeywell thermostat:
Note: To register your Honeywell WiFi devices, you must have each device’s
MAC ID and Device CRC.
1. Access the Honeywell WiFi portal at
https://mytotalconnectcomfort.com/portal.
2. Log into the website.
–or –
Create an account, and then log in.
3. Add a location.
Adding the location launches a registration wizard.
4. Complete the wizard to register your devices.
Note: You will need the thermostats name for Fusion. The name is case
sensitive and must match the name in Honeywell.
Enabling auto mode
For auto mode to function in the Clare Controls App, auto mode must be enabled
on the thermostat. This process varies by thermostat. Below are some examples.
Note: It is necessary to enable auto mode when its used with the Clare Controls
App.
To enable auto mode in the Honeywell 8321:
1. Disconnect the thermostat from the wall mount to view the back.
2. Note the pin code, and then connect the thermostat to the mount.
3. Press Menu, and then press the down arrow until the Installer Options
displays.
4. Tap Select and enter the pin code as prompted.
5. Press Done to view the Installer Menu, and then press the down arrow until
the Installer Setup displays.
6. Press Select, and then press Next until the System Changeover displays.
7. Toggle the System Changeover to automatic, and then press Done.
8. Tap Yes to exit the menu.

Doc ID - 1188 • Rev 04 4 / 8
To enable auto mode in other Honeywell 8000 models:
1. Access the thermostat, and then press System.
2. Press and hold the blank center button.
3. Press the up arrow until 0300 is displayed.
4. Change the value to 1, and then exit the menu.
To enable auto mode in the Honeywell 9000:
1. Access the thermostat, and then press MENU.
2. Browse to Advanced Preferences.
Preferences > Advanced Preferences
3. Press the Next button until the Heating and Cooling System Changeover
screen displays.
4. Press Automatic, and then press Done.
5. The Exit screen displays, press Yes to save your changes.
Configuring in Fusion
Once the thermostat has been installed, registered, and set to auto mode,
configure the Honeywell thermostat in Fusion.
To add the Honeywell WiFi device in Fusion:
1. Click the Devices tab, and then click the New Device button to display the
Select Template dialog.
2. Expand the Climate folder, and browse to the Honeywell WiFi Thermostats.
Climate > IP Thermostats > Honeywell WiFi Thermostats

Doc ID - 1188 • Rev 04 5 / 8
3. Click OK.
The Details tab displays.
4. Enter a name and notes for the thermostat.
5. Click the Configure tab.
6. Enter values in the following fields:
•Thermostat ID: Enter the thermostat number associated with that
thermostat.
Note: Fusion sets the Thermostat ID to 1 by default. This number only
needs to be changed if there is more than one thermostat in use. We
recommend assigning the thermostats IDs in order. The first thermostat
added is 1, the second thermostat is 2, and so on.
•Device Name: The thermostats name in the Honeywell WiFi portal.
Note: The names in the Honeywell portal and Fusion must be identical or
the thermostat will not connect. The names are case sensitive.
•Username: The username used for the Honeywell WiFi portal.
•Password: The password used for the Honeywell WiFi portal.

Doc ID - 1188 • Rev 04 6 / 8
7. Click the Save button .
8. The Create Service dialog displays. Click OK, and the service is automatically
created for you.
Note: You can select Open Wizard to check or change the controls points as
needed.
9. Configure rules to work with your thermostat.
Configuring rules with TCC thermostats
Configure a rule for your thermostat. The example below shows how to set a rule
for alerting the customer of the home’s temperature. If the thermostat reaches
above 72°F, an email notification is sent.
To create a rule for the TCC thermostat in Fusion:
1. Access your project, and then click the Rules tab.
2. Click the New Rule button .
3. Enter a name for the rule, and then select the Enable Rule checkbox.

Doc ID - 1188 • Rev 04 7 / 8
4. Configure the Event Part as below.
•Event Type: Device Property Change Event
Note: This event type is replacing the Device Property Value Event.
•Device: Honeywell WiFi thermostat
•Function: Heat Cool Temperature Actuator
•Property: Unit
•Constraint: >
•Value: 72
5. Configure the Action part as below.
•Action Type: Send Email
•Recipients: The homeowner’s Email address
Note: To add an Email address, you must click the green plus icon . Do
this for each desired Email recipient.
•Subject: The purpose of the alarm
•Text: The information included in the email
6. Click the Save button , and then deploy the project.

Doc ID - 1188 • Rev 04 8 / 8
Contact information
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
General: 941.328.3991
Fax: [phone]
www.clarecontrols.com
Integrator/Dealer Support: 941.404.1072
[email protected]
Homeowner Support (ClareCare): 941.315.2273 (CARE)
[email protected]