Hoover H-HOB 300 User manual

CANDY HOOVER GROUP S.R.L. • Via Privata Eden Fumagalli • 20047 Brugherio Milano Italy
GB
IT
CZ
FR
NL
DE
HOBS
USER INSTRUCTIONS
PIANI COTTURA
ISTRUZIONI D’USO E DI INSTALLAZIONE
VARNÉ DESKY
NAVOD POU ŽITĺ
TABLE DE CUISSON
NOTICE D’EMPLOI ET D’INSTALLATION
KOOKPLAATS
INSTALLATIE-EN GEBRUIKSINSTRUCTIES
KOCHMULDE
GEBRAUCHS - UND INSTALLATIONSANWEISUNGEN
PLACAS
INSTRUCOES DE UTILIZACAO
KEITTOTASOT
KÄYTTÖOHJEET
PLATETOPPER
BRUKERINSTRUKSJONER
SPISHÄLLAR
ANVÄNDARINSTRUKTIONER
KOGESEKTIONER
BRUGSANVISNING
PT
FI
NO
SV
DA

SOMMAIRE FR
CONSIGNES DE SÉCURITÉ
1. Avertissements généraux
2. Protection de l'environnement
3.Installation
4. Raccordement électrique
5. Conseils concernant les ustensiles de
oncuisine pour la table de cuiss
6. Utilisation
7. Nettoyage et entretien
8. Résolution de problèmes
Contrôle d'entretien préliminaire9.
........................... ........27.....
..........................................28
...................................28
.................... .....................28............... ..........
. ......................................29....
.....................................31
. ....................................................31.............
. ......... .......................33........... ....
....... .... .......................33.... ......
. .......................34..........
INHOUD NL
VEILIGHEIDSAANWIJZINGEN
1.Algemene waarschuwingen
2.Bescherming van het milieu
3.Installatie
4.Elektrische aansluiting
5.Advies over te gebruiken pannen
6.Gebruik
7.Reiniging en onderhoud
8.Problemen oplossen
9.NAZORG
......................................35
.........................................36
........................................36
............. ................................36............... ..........
. ............................................37....
................................39
. ..........................................................39.............
. ..............................41...............
....... ...................................41..........
. ...................................................42.................
INHALT DE
SICHERHEITSHINWEISE
1.Allgemeine Warnhinweise
2.Umweltschutz
3.Installation
4.Elektrischer Anschluss
5.Tipps zum Kochgeschirr
6.Benutzung
7.Reinigung und Wartung
8.Problembehebung
9.Kundendienst
................................. ........43.....
............................................44
..............................................................44
............. .............................44............... ..........
. ...........................................45....
...............................................47
. .....................................................47.............
. ...............................49...............
....... ......................................49..........
. .............................................50.................
CONTEÚDO PT
INSTRUÇÕES DE SEGURANÇA
1.Avisos gerais
2.Proteção do ambiente
3.Instalação
4.Ligação elétrica
5.Conselhos de utensílios de cozinha
6.Uso
7.Limpeza e manutenção
8.Resolução de problemas
9.Pós-tratamento
............................. ....51..
................................................................52
..................................................52
............. ...............................52............... ..........
. .......................................................53....
.............................55
. .................................................................55.............
. ................................57...............
....... .............................57..........
. ...............................................57.............
INDICE IT
ISTRUZIONI DI SICUREZZA
1. Avvertenze generali
2. Salvaguardia dell'ambiente
3.Installazione
4. Collegamento elettrico
5. Consigli sui recipienti di cottura per il piano
6. Uso
7. Pulizia e manutenzione
8. Risoluzione del problema
9. Manutenzione aggiuntiva
10. Garanzie
............................. ........11....
..................................................12
.......................................12
.. ............. ........................12.......... ..... ..........
..... .........................................13
..............15
. ................................................................ ...........15
. .......................................... 17
....... ................................... 17
. .......................................... 18
18.................. .................................................
OBSAH CZ
BEZPEČNOSTNÍ OPATŘENÍ
1. Všeobecná upozornění
2. Ochrana životního prostředí
3.Instalace
4. Elektrické připojení
5. uDoporučení ohledně nádobí pro varnou desk
6. Použití
7. Čištění a údržba
8. Řešení problémů
9. Následná péče
............................. ........19...
.............................................20
......................................20
............. ...............................20............... ..........
. ...............................................21....
..........23
. ..........................................................23.............
. ........................................25...............
....... ......................................25..........
. ........................................25.................
CONTENT GB
SAFETY INSTRUCTIONS
1. General arningsw
2. Protection of the environment
3. Installation
4. Electrical conne ionct
5. Hob cookware advice
6. Use
7. C and maintenanceleaning
8. Problem solving
Aftercare9.
.............................................03
.......................................................04
....................................04
. ............. ..............04. ........................... ..........
............. ................................. 5.... 0
................................................07
. ................................................07...........................
.....................09...................
................................. ..............09..........
.............................. ..............09........................
SISÄLTÖ FI
TURVALLISUUSOHJEET...............................................59
1. Yleisiä varoituksia........................................................60
2. Ympäristönsuojelu.......................................................60
3. Asennus......................................................................60
4. Sähköliitäntä
5. Keittotasolle sopivat keittoastiat.................................63
6. Käyttö
7. Puhdistaminen ja ylläpitohuolto
8. Ongelmien ratkaisu ...................................................65
9. Myynninjälkeinen palvelu
..... ..........................................................61
.......... ................................................................63
....... ............................65
........................................................65

INNHOLD NO
SIKKERHETSINSTRUKSJONER
1. Generelle advarsler
3. Installasjon
4. Elektrisk tilkobling
5. Anbefalinger om kokekar å bruke på platetoppen.....71
6. Bruk
7. Rengjøring og vedlikehold
8. Problemløsning
9.
.................................67.....
..................................................68
2. Beskyttelse av miljøet ...............................................68
............... .............................. ....................68
..... ...............................................69
....................... ...................................................71
... ..... ......... .......................73
.... ............. .............................................73
Etterbehandling .......... ...............................................73
INNEHÅLL SV
SÄKERHETSINSTRUKTIONER
1. Allmänna varningar
3. Installation
4. Elanslutning
5. Råd om köksutrustning ............................................79
6. Användning
8. Problemlösning
9.
.................................................76
2. Skydd av miljön .......................................................76
............... .............................. ...................76
..... .......................................................77
............ ...................................................79
7. Rengöring och skötsel
. ... .... ......... .............................................81
....... .... ..................................................81
Eftervård..................... ...............................................81
................................75
INDHOLD DK
SIKKERHEDSANVISNINGER
1. Generelle advarsler
3. Installation
4. Elektriske forbindelser
5. Råd om kogegrej ......................................................87
6. Brug
8. Problemløsning
9.
..................................................84
2. Miljøbeskyttelse .......................................................84
............... .............................. ....................84
..... ..........................................85
....................... ..................................................87
7. Rengøring og vedligeholdelse
....... .... ...................................................89
Service .......... ............................................................89
....... .... ...............................89

We recommend you keep the instructions for
installation and use for later reference, and before
installing the hob, note its serial number in case
you need to get help from the after sales service.
WARNING: the appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements. Children under
8 years of age must be kept away from the
appliance unless they are continuously
supervised.
WARNING: use only hob guards designed by the
Manufacturer of the cooking appliance or
indicated by the Manufacturer of the appliance in
the instructions for use as suitable or hob guards
incorporated in the appliance. The use of
inappropriate guards can cause accidents.
WARNING: unattended cooking on a hob with fat
or oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but
switch off the appliance and then cover flame e.g.
with a lid or a fire blanket.
WARNING: danger of fire: do not store items on
the cooking surfaces.
WARNING: if the surface is cracked, do not touch
the glass and switch off the appliance to avoid the
possibility of electric shock.
This appliance can be used by children aged from
8 years and above and people with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children should be supervised
to ensure that they do not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
CAUTION: the cooking process must be
supervised. A short term cooking process has to
be supervised continuously.
It is strongly recommended to keep children away
from the cooking zones while they are in operation
or when they are switched off, so long as the
residual heat indicator is on, in order to prevent
the risks of serious burns.
This appliance is not intended to be operated by
means of an external timer or separate remote
control system.
If present do not to stare into halogen lamp hob
elements.
Connect a plug to the supply cable that is able to
bear the voltage, current and load indicated on the
tag and having the earth contact. The socket must
be suitable for the load indicated on the tag and
must be having the earth contact connected and
in operation. The earth conductor is yellow-green
in color. This operation should be carried out by a
suitably qualified professional. In case of
SAFETY INSTRUCTIONS
incompatibility between the socket and the
appliance plug, ask a qualified electrician to
substitute the socket with another suitable type.
The plug and the socket must be conformed to
the current norms of the installation country.
Connection to the power source can also be
made by placing an omnipolar breaker between
the appliance and the power source that can bear
the maximum connected load and that is in line
with current legislation.
The yellow-green earth cable should not be
interrupted by the breaker. The socket or
omnipolar breaker used for the connection
should be easily accessible when the appliance is
installed.
The disconnection may be achieved by having
the plug accessible or by incorporating a switch in
the fixed wiring in accordance with the wiring
rules.
If the supply cord is damaged, it must be replaced
by Manufacturer, its service agent or similarly
qualified people in order to avoid a hazard. The
earth conductor (yellow-green) must be longer
than 10 mm on the terminal block side. The
internal conductors section should be
appropriate to the power absorbed by the hob
(indicated on the tag). The type of power cable
must be HO5V2V2-F.
Do not put metallic objects such as knives, forks,
spoons or lids on the hob. They could heat up.
Aluminum foil and plastic pans must not be
placed on heating zones.
After every use, some cleaning of the hob is
necessary to prevent the build-up of dirt and
grease. If left, this is recooked when the hob is
used and burns giving off smoke and unpleasant
smells, not to mention the risks of fire
propagation.
Never use a steam or high pressure spray to
clean the appliance.
Do not touch the heat zones during operation or
for a while after use.
Never cook food directly on the glass ceramic
hob.
Always use the appropriate cookware.Always
place the pan in the center of the unit that you are
cooking on.
Do not place anything on control panel.
Do not use the hob as a working surface.
Do not use the surface as a cutting board.
Do not store heavy items above the hob. If they
drop onto the hob, they may cause damage.
Do not use the hob for storage of any items.
Do not slide cookware across the hob.
No additional operation/setting is required in
order to operate the appliance at the rated
frequencies.
03 GB

Leave a distance of at least 55
mm between the hob and the
back wall and of at least 150
mm between the hob and the
vertical furniture or walls in the
lateral side. If a furniture is
installed above the hob, the
minimum distance required is
700 mm.
When installing a hood above
the hob, please consult the
installation requirements
specified for the hood but, in
any case, the distance between
the hob and the hood must not
be lower than 700 mm.
PRODUCT CODE T
Identification Plate (located under the hob's bottom casing)
1. GENERAL WARNINGS
By placing the mark on this appliance we are assuring
compliance to all European Safety, Health and Environment
requirements which are applicable for this product category.
2. PROTECTION OF THE ENVIRONMENT
This appliance is marked according to European
Directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE).
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components which can be
reused.It is important to have WEEE subjected to
specific treatments, in order to remove and dispose
properly all pollutants and recover and recycle all
materials.
Individuals can play an important role in ensuring that the WEEE
does not become an environmental issue; it is essential to follow
some basic rules:
• WEEE shall not be threatened as household waste.
• WEEE shall be handled over to the relevant collection points
managed by the municipality or by registered companies. In many
Countries, for large WEEE, home collection could be present.
• In many Countries, when you buy a new appliance, the old one
may be returned to the retailer who has to collect it free of charge on
a one-to-one basis, as long as the appliance is of equivalent
typology and has the same functions as the supplied one.
3 INSTALLATION.
Installing a domestic appliance it is a complicated operation which, if
not carried out correctly, can seriously have impact on safety of goods,
properties or people. For this reason, it should be carried out by a
professionally qualified person in accordance with technical
regulations.
In the event that this advice it is ignored and installation is carried out
by an unqualified person, the Manufacturer declines all responsibility
for any technical failure of the appliance whether or not it results in
damage of goods or properties or in injury of people or animals.
After having removed the packaging please be sure that the appliance
it is not damaged, otherwise contact the Retailer or ManufacturerAfter
Sales Service.
Make sure that the furniture in which the appliance will be fitted and all
other furniture in the nearby are made with materials which can
withstand high temperatures (min 100 °C).
In addition, all decorative laminates should be fixed with high-resistance
glue.
Appliance can be installed in a Built-in furniture in “Standard” or “Flush”
mode.
700 mm 55 mm
150 mm
490 mm
+ 2
- 0
560 mm
+ 2
- 0
Min. 70 mm
Standard installation
perimeter
Note: Inner perimeter dimensions are same with standard installation
703 mm (70 cm hob)
+2
-0
523 mm
+ 2
- 0
593 mm (60 cm hob)
+2
-0
Slot depth: 5 mm
Flush installation
perimeter
Worktop thickness should be between 25 and 45 mm.
If the bottom part of the hob is adjacent to an area normally accessible
for handling or cleaning operations, a separator it must be put 0 mm2
below the bottom part of the hob.
min 20 mm
When installing an oven under the hob, separator must not be put and
the minimum distance between the bottom part of the hob and the
oven must not be lower than 10 mm. Do not install not cooled oven
under this hob and install the oven following its own installation
requirements.
10 mm
min
04 GB

6
6
5
5
3
1
2
4
5
5
6
6
1
2
366
6
45
5
5
6
6
5
5
3
1
2
5
5
6
6
1
2
3
6
6
6
5
5
5
FLUSH INSTALLATION
After checking that the position of
the hob is correct fill the gap
between the worktop and the hob
with silicone adhesive. Flatten the
silicone layer with a scraper or
with wet finger damped with water
and soap before it forms.
Do not use the hob until the
silicone layer it is completely dry.
A watertight seal gasket is
supplied with the hob. Fit
the seal gasket around the
bottom hob as described
and make sure that it is
properly fitted to avoid any
leakage into the supporting
furniture.
4. ELECTRICAL CONNECTION
Bottom
Normal Fixing:
- Get the fixing clips from accessory bag
and screw them into the position shown
on bottom box. (Do not tighten the
screws to block clips, they should move
freely)
- Insert the hob in center
position of cut out.
- Turn the clips and tighten
them fully.
Quick Fixing: (Depending on model)
Get four springs form accesory bag and
screw them onto bottom box as shown
in figure.
Center and insert the hob.
Press the sides of hob until it
is supported around its
entire perimeter.
1-3
2-4
5
6
7
LAYOUT
According to model
1."+"
2"."-
3. TIMER
4.Additional cooking zone led
5. Cooking zone programming indicator
6. Selection of the zone
7. Bridge
AB
CD
A
B
C
AB
CD
A
B
C
A
C
B
C
AB
D
AB
CD
05 GB

"Installation must conform to the standards & directives."
Manufacturer declines all responsibility for any damage that
might be caused by unsuitable or unreasonable use.
WARNING: Manufacturer cannot be held responsible for any incident
or its consequences that may arise during the use of an appliance not
linked to the earth, or linked to an earth whose continuity is defective.
Before any electrical operation, please check the supply tension
shown on the electricity meter, the adjustment of the circuit- breaker,
the continuity of the connection to earth to the installation and that the
fuse is suitable.
The electrical connection to the installation should be made according
to the rated power of the Appliance; this should be made via an Omni
pole cut-out switch.
If the appliance has a socket outlet, it must be installed so that the
socket outlet is accessible.
The yellow/green wire of the power supply cable must be connected to
the earth of both power supply and appliance terminals.
For any questions regarding power supply cord refer to After Sales
Service or a qualified technician.
If the hob is fitted with power supply cord, this shall be connected only
to a power supply of 220-240 V between phase and neutral.
It is however possible to connect the hob to:
Three Phase 220-240 V3
Three Phase 380-415 V2N
To proceed to the new connection, please follow below instructions:
Before making the connection, make sure that the installation is
protected by a suitable fuse, and that it is fitted with wires of a large
enough section to supply the appliance normally.
Turn over the hob, glass side against the working top, taking care to
protect the glass.
Open the cover in the following sequence:
- unscrew the cable clamp "1";
- find the two tabs located on the sides;
- put the blade of a flat screw-driver in front of each tab "2" e
"3", push in and press;
- remove the cover.
To release the power supply cord:
- Remove the screws retaining the terminal block which
contains the shunt bars and the conductors of the supply cord;
- Pull out the supply cord.
Operations to be carried out to make a new connection:
- Choose the power supply cable in accordance with the
recommendations in the table;
- Pass the power supply cable into the clamp;
- Strip the end of each conductor of the supply cord on a 10 mm length,
by taking in account the requested length of the cord for the
connection to the terminal block;
-According to the installation and with the help of shunt bars which you
should have recovered in the first operation, fix the conductor as
shown on the chart;
- Fix the cover;
- Screw the cable clamp.
Connection to the terminals on the terminal block
ATTENTION:
If it should be necessary to replace the power supply cord, connect the
wire in accordance with following colors/codes:
LAY OUT
"1-6"
LAY OUT
"7"
MONOPHASE or TWO PHASES 220-240 V~
Cable
HO5V2V2F
Cable
HO5V2V2F
Cable
HO5V2V2F
3x2,5 mm23x4 mm2
4x1,5 mm24x1,5 mm2
4x1,5 mm24x1,5 mm2
THREE PHASES 220-240 V3~
THREE PHASES 380-415 V2N~
Note: make sure the terminal board screws are tight.
Operations to be carried out to make a new connection:
- Choose the power supply cable in accordance with the
recommendations in the table;
- Pass the power supply cable into the clamp;
- Strip the end of each conductor of the supply
cord on a 10 mm length, by taking in account
the requested length of the cord for the
connection to the terminal block;
- According to the installation and with the help
of shunt bars which you should have recovered
in the first operation, fix the conductor as shown
on the chart;
- Fix the cover;
- Screw the cable clamp.
06 GB
SHUNT
N=Neutral PE =EarthL1 / L2 / L3 = Phase
220-240V 3 ~
PE L1 L2 L3
380-415V 2N ~
N
PE L1 L2
L3
PE L1
L2
220-240V ~
N
L
220-240V 2 ~
L2
PE L1
PE
231

07 GB
5. HOB COOKWARE ADVICE
Using good quality cookware is critical for setting
the best performance from your hob.
•Always use good quality cookware with perfectly flat and thick
bases : using this type of cookware will prevent hot spots that cause
food to stick. Thick metal pots and pans will provide an even
distribution of heat.
• when filling pansEnsure that the base of the pot or pan is dry :
with liquid or using one that has been stored in the refrigerator, ensure
that the base of the pan is completely dry before placing it on the hob.
This will help to avoid staining the hob.
•Use pans whose diameter is wide enough to completely cover
the surface unit : the size of the pan should be no smaller than the
heating area. If it is slightly wider the energy will be used at its
maximum efficiency.
THE CHOICE OF COOKWARE - The following information will help
you to choose cookware which will give good performance.
Stainless Steel : highly recommended. Especially good with a
sandwich clad base. The sandwich base combines the benefits of
stainless steel (appearance, durability and stability) with the
advantages of aluminium or copper (heat conduction, even heat
distribution).
Aluminium : heavy weight recommended. Good conductivity.
Aluminium residues sometimes appear as scratches on the hob, but
can be removed if cleaned immediately.
Because of its low melting point, thin aluminium should not be used.
Cast Iron : usable, but not recommended. Poor performance. May
scratch the surface.
Copper Bottom / stoneware: heavy weight recommended. Good
performance, but copper may leave residues which can appear as
scratches. The residues can be removed, as long as the hob is
cleaned immediately. However, do not let these pots boil
dry. Overheated metal can bond to glass hobs. An overheated copper
pot will leave a residue that will permanently stain the hob.
Porcelain/enamel : Good perfomance only with a thiny smooth, flat
base.
Glass-ceramic : not recommended. Poor performance. May scratch
the surface.
1) If any cooking stage is in position 0, this display will switch OFF
automatically after 10 seconds and the zone OFF sequence will
sound.
2) If there is residual heat indication in the display which is OFF, "H" will
be displayed.
3) Even lock function is active you can switch OFF a zone.
4) If only one heater is active and this one is switched off, 4 Short beep
will be heard indicating all cook top is Off.
Switch ON/OFF a heater zone
To switch ON a heater Touch any heater´s zone during 400 msec.
Long beep will be heard and "0" value will appear in target zone digit,
indicating power level.
1) If any cooking stage is in position 0, this display will switch OFF
automatically after 10 seconds and the zone OFF sequence will
sound.
2) If there is residual heat indication in the display which is ON but in 0
power, "0" will appear changing over.
3) If lock function is active you cannot switch ON a zone.
To switch OFF a heater Touch any heater´s zone during 1,2 sec. 3
Short beeps will be heard and nothing or "H" value will appear in
target zone digit if residual heat exists. Zone will be OFF.
6. USE
Through the "Power management" function, the user can set the
maximum power that can be reached by the hob. Power management
function is only available during first 30 seconds after switch on the
hob. There is even the possibility to repeat this setting switching off
and on the power plug. By setting the desired maximum power, the
hob automatically adjusts the distribution in the various cooking zones
so that this limit is never exceeded; with the added advantage of being
able to simultaneously manage all the zones without overload
problems. The customer can set the maximum power of hob between
2.5 kW and the maximum related power of the hob (this can change
according to the model) (for example if the maximum power of the hob
is 7.2 kW. The maximum power level for setting is between 2.5kW and
7.2kW)At the time of purchase, the hob is set to maximum power. After
connecting the appliance to the electrical power, within 30 seconds
you can set the power level based on the points shown below:
1.- Switch on hob.
2.- Let touch control finish its initialization process.
3.- Before pass 30 seconds touch during 5 seconds ‘ key.
4.-After this moment, this message will appear on display.
How to choose power management level
P
5.- Using ‘Plus’ and ‘Minus’ keys Power management value can be
adjusted. In this example case between 6500 and 2500w. When
required value is selected, touch at the same time ‘Plus’ & ‘Minus’keys
during 5 seconds.
6.- When this process is finished, a long beep is heard and a reset is
produced. Start-up process will be generated again.
7.- After start-up process, in timer display ECO power management
will be showed.
After that, touch control won´t allow any combination which
can exceed this Eco limit.
P
45
00

Child Lock option
This action will be done when ‘+’ & ‘-‘keys were touched at the same
time.
Then, any time when a key will be touched, displays will show "L"
during 2sec. heating remains at the same state.
To deactivate Child Lock, follow the same process explained before.
Then Short beep will be heard and displays will show "n" letter. Hob will
remain unlocked.
Note: An automatic child lock will produce in 15 minutes after total
Switch OFF of the hob.
Selecting a zone
When zone is already ON a lower lighting intensity for the not selected
zones that are ON is produced.
If only one zone is ON, this zone is already selected by default, without
needing to short press (150 msec) over selection key.
Increase / Decrease power level
With a short press on ‘+’ or ‘-‘ keys, Increase or decrease power in the
selected zones digit: 0-1-2-3...9-P
1. For Long Presses in + or - keys, power level increases /decreases
continuously. With a fast increase, power stops at level 9, and for a
higher power another short press is needed on the + key. No beep
sound is heard with fast increase / decrease.
2. Once arrived to P power level, pressing + key again does not
change power level to 0.Once arrived to 0 power level, pressing - key
again does not change power level to P.
3. With a zone ON at 0 power level, if the zone is hot, 0 will blink
alternatively.After 10 seconds, 0 will disappear an ‘H’ letter will appear
fixed on display.
4. When a heater is selected and ‘+’ & ‘-‘keys are touched at the same
time, power level will go to ‘0’ but heater will maintain selected during
10 seconds. If heater was temporized, timer will go to Off. This action
can only be developed in several cases depending touch control
configuration.The following examples are for information only.
Personal experience should then let you adapt these settings to your
taste and habits.
To switch ON double extension ring, associated main zone must be
already ON and Indicating power level must be higher than 0.
8.1- Double zone ON
1st Short Press on extension key Switches ON extension ring. LED
over extension key turns ON if Extension ring is ON.
2nd Short Press on extension key Switches OFF extension ring.
Short beep each press on extension key.
8.2- Triple zone ON
1st Short Press on extension key Switches ON 1st extension ring. 1
LED over extension key turns ON if 1st extension ring is ON (left LED
in case of triple zone, middle and only LED in case of double zone) 2nd
Short Press on extension key Switches ON 2nd extension ring.
Double / Triple zones
Bridge function
The bridge can be enabled only when both heaters are off. One heater
of the bridge has been selected, to activate bridge function touch
bridge key.
Abeep sounds and the zone LED is switched on if the zone is enabled.
Both bridge heaters will be selected at the same time.
Once the heaters selected, if the power level is not the desired power
level, by the + - keys.
Both bridge heater displays will show same power level.
The function will finish:
- If the bridge key is touched in setting mode
- If user selects power level “0”
Overflow security
Something (an object or a liquid) is pressing any key during more than
5s. 2 Short Beep + 1 Long beep every 30s while the key is pressed.
Cook-top will turn Off. This symbol will maintain blinking while the
matter persist.
Timer
Timer function can be activated with its own key.
Select the zone to be timed. Power level of the zone greater than 0.
Static is displayed in the zone being timed . "0 0" in the digits
reserved for the timer.
1) With "+" or "-" keys, timer time can be chosen. No Beeps at time
change.
2) Pressing continuously timer key, the timer is cancelled (goes to 00).
3) If timer "+" or "-" keys is maintained pressed there is quick setting.
4) When setting timer time, it is possible to go from "00" to "99" with "-"
key, and from "99" to "00" with "+" key.
5) Maximum time 99 minutes.
6) When the time is elapsed and the hob is beeping, press any key and
the alarm and digit sequence will end.
7) It is possible to adjust the timer time while the timer is previously
running.
8) Power of timed zone can be modified without consequences on the
timer programming.
9) Last minute will be displayed by seconds (For Variants only visible if
we enter the timer programming while the last minute of the
countdown)
10) Pressing the Timer key without any selected zone and when no
zone is being timed, does nothing.
11) Pressing the Timer key without any selected zone and when many
zones are being timed, the time shown in time digits changes in a
rotatory way, and shows the time whose power display has the
decimal point ON.
12) Alternatively Power (5s) and (0,5s) is displayed in the zone being
timed.
Remaining time is displayed in the digits reserved for the timer. If
multiple zones are timed, the smallest remaining time is displayed,
and the decimal point is displayed in the corresponding zone.
2 LEDs over extension key turn ON if 1st and 2nd extension rings are
ON 3rd Short Press on extension key. Switches OFF 1st and 2nd
extension rings.
Short beep each press on extension key.
Residual Heat Indicator (In radiant heaters-> calculated)
The same indicators can be used for “residual heat” indication as well.
A time table must be defined on this purpose: Rest Heat time=f (power
level, working time).
While a temperature on the cook top glass surface is above
65 Cb(theory value), this condition will be shown in the associated
o
display, by means of an “H”.
To generate a temperature above 65 C a heating element has to be in
o
operation for certain time, this time depends on the power level. Once
this time has expired, the residual heat warning will be shown when
the heating element is switched off.
08 GB

09 GB
Automatic Safety Off
If the power level is not changed during a preset time, the
corresponding heater turns off automatically.
The maximum time a heater can stay on, depends on the selected
cooking level.
Power level Max. time on (hours)
1
2
3
4
5
6
7
8
9
P
10
5
5
4
3
2
2
2
2
2
NOTE: while an overheating situation should occur during the
operation of the highest power levels, the Hob control will
automatically adjust the power level in order to protect the hob from
overheating.
7. CLEANING AND MAINTENANCE
. Before carrying out any maintenance work on the hob, allow it to
cool down.
.Only products, (creams and scrapers) specifically designed for
aglass ceramic surfaces should be used. They are obtainable from
hardware stores.
.Avoid spillages, as anything which falls on to the hob surface will
quickly burn and will make cleaning more difficult.
.It is advisable to keep away from the hob all substances which are
liable to melt, such as plastic items, sugar, or sugar-based products.
.MAINTENANCE:
- Place a few drops of the specialised cleaning product on the hob
surface.
- Rub any stubborn stains with a soft cloth or with slightly damp
kitchen paper.
- Wipe with a soft cloth or dry kitchen paper until the surface is clean.
If there are still some stubborn stains:
- Place a few more drops of specialised cleaning fluid on the surface.
- Scrape with a scraper, holding it at an angle of 30° to the hob, until
the stains disappear.
- Wipe with a soft cloth or dry kitchen paper until the surface is clean.
- Repeat the operation if necessary.
AFEW HINTS:
Frequent cleaning leaves a protective layer which is essential to
prevent scratches and wear. Make sure that the surface is clean
before using the hob again. To remove marks left by water, use a few
drops of white vinegar or lemon juice. Then wipe with absorbent paper
and a few drops of specialised cleaning fluid.
The glass ceramic surface will withstand scraping from flat-bottomed
cooking vessels, however, it is always better to lift them when moving
them from one zone to another.
NB:
Do not use a sponge which is too wet.
Never use a knife or a screwdriver.
A scraper with a razor blade will not damage the surface, as long
as it is kept at an angle of 30°.
Never leave a scraper with a razor blade within the reach of
children.
Never use abrasive products or scouring powders.
.The metal surround : to safely clean the metal surround wash with
soap and water, rinse, then dry with a soft cloth.
30° Maxi
Any change in the colour of the glass-ceramic surface does
not affect its operation or the stability of the surface. Such
discolorations are mostly a result of burnt food residues or
use of cookware made of materials such as aluminium or
copper; these stains are difficult to remove.
8. PROBLEM SOLVING
The cooking zones do not simmer or only fry gently
Only use flat-bottomed pans. If light is visible between the pan and the
hob, the zone is not transmitting heat correctly.
The pan bottom should fully cover the diameter of the selected zone.
The cooking is too slow
Unsuitable pans are being used. Only use flatbottomed utensils, that
are heavy and have a diameter at least the same
as the cooking zone.
Small scratches or abrasions on the hob's glass surface
Incorrect cleaning or rough-bottomed pans are used; particles like
grains of sand or salt get between the hob and the bottom of the pan.
Refer to the "CLEANING" section; make sure that pan bottoms are
clean before use and only use smooth bottomed pans. Scratches can
be lessened only the cleaning is done correctly.
Metal marks
Do not slide aluminium pans on the hob. Refer to the cleaning
recommendations.
You use the correct materials, but the stains persist.
Use a razor blade and follow the "CLEANING" section.
Dark stains
Use a razor blade and follow the "CLEANING" section.
Light surfaces on the hob
Marks from an aluminium or copper pan, but also mineral, water or
food deposits; they can be removed using the cream cleaner.
Caramelisation or melted plastic on the hob.
Refer to the "CLEANING" section.
The hob does not operate or certain zones don't work
The shunts are not positioned correctly on the terminal board.
Have a check made that the connection is done he control panel is
locked. Unlock the hob.
The hob does not cut off.
The control panel is locked. Unlock the hob.
Frequency of on/off operations for cooking zones
The on-off cycles vary according to the required heat level:
- low level: short operating time,
-high level: long operating time.
The cooktop is not working.
Check the condition of the fuses / circuit breakers at your
location.Check to see if you are experiencing a power failure.
The cooktop has turned itself off.
The main switch (ON/OFF key) was accidentally touched or there is
any object above any key. Turn the unit on again without any object
about the keyboard. Enter your settings again.
Display F and numbers
If and numbers appears in the display, your unit has detected a fault.F
The following table list actions you can take to correct the problem.
9. AFTERCARE
Before calling out a Service Engineer please check the
following:
— that the plug is correctly inserted and fused;
If the fault cannot be identified switch off the appliance — do not
tamper with it — call the Aftercare Service Centre. The appliance is
supplied with a guarantee certificate that ensures that it will be
repaired free of charge at the Service Centre.