Hoover ONEPWR Emerge User manual

EMERGE
CORDLESS VACUUM
EMERGE PET
CORDLESS VACUUM
USER GUIDE
F18OPSV22Z
F18OPSV22J2

IMPORTANT SAFETY INFORMATION
This machine is intended for household use only and NOT for commercial or
industrial use. This machine is intended for dry vacuuming only. Do not use this
machine for any other purpose. PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND
USE ONLY AS INSTRUCTED IN THIS GUIDE.
• Don’t leave the charger plugged in when unattended.
• Don’t use the machine if it is faulty or has been dropped, damaged or left
outdoors.
• Don’t use the machine to pick up any flammable or combustible materials
(lighter fluid, petrol, kerosene etc.) or use the machine in an area with explosive
vapours or liquid.
• Don’t use the machine to pick up hot coals, cigarette butts, matches or smoking
hot burning items or use in an area where there may be harmful fluids (chlorine,
bleach and ammonia drain cleaner).
• Don’t handle the charger, battery or use the machine with wet hands.
• Don’t unplug the charger by pulling on the power cord.
• Don’t use the charger if the power cord or plug is damaged.
• Don’t attempt to remove blockages with sharp objects as this may cause damage
to the machine.
• Don’t use the machine with the incorrect battery or charger as this may result in
damage or injury to the user. The correct battery charger information is listed on
the battery pack ratings label.
• Don’t charge the battery outdoors, or leave the charger connected to the mains
when not in use.
• Don’t use the machine with a damaged battery. If the battery is damaged return
the machine, battery and charger to the point of purchase.
• Don’t over fill the dirt container to avoid blocking the air flow through the
machine.
• The brushbar in the powered head constantly rotates when switched on. Never
use the powered head on one spot for an extended period of time as the
brushbar may damage the floor surface.
• Only Hoover ONEPWR batteries and chargers should be used with this machine.
• Only Hoover ONEPWR recommended tools and accessories should be used with
this machine.
• Always remove the battery from the machine before carrying out any
maintenance or if storing unused for a long period of time.
2

• Keep all openings clear and free from debris as this may affect the
airflow/suction.
• Turn off all controls on the machine before disconnecting or connecting the
battery.
• Always protect the charger power cord from heated surfaces or near open
flames.
• Only use the machine indoors on dry surfaces and keep the area you’re cleaning
well lit.
• The power cord cannot be replaced. If the cord is damaged the charger should
be scrapped.
• Do not use this charger to charge non-rechargeable batteries.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Keep fingers, hair and loose clothing away from moving parts and openings
whilst using the machine.
• Store the machine in a cool, dry area. Keep the machine away from rain and
moisture.
• Take extra care when using the machine on the stairs.
• Use only Australian/New Zealand approved 10amp extension cords, non-approved
extension cords may overheat. Care should be taken to arrange the extension
cord as it can be a trip hazard.
• To prevent any damage being sustained, test on an inconspicuous area of the
flooring first.
• Always make sure the separator and filter are fitted correctly before using your
machine and only use the machine with the filter and separator in place.
• Always check the powered head and accessories are free from damage, dirt and
debris before using.
• This machine does not stay upright without constant support. Between uses, lie
flat on the floor in a suitable location so that it does not become a trip hazard or
can be stepped on.
IMPORTANT SAFETY INFORMATION
3

IMPORTANT SAFETY INFORMATION
BATTERY SAFETY PRECAUTIONS
• Replace the battery with a Hoover ONEPWR battery only. Use of another battery
may present a risk of fire or explosion.
• Do not attempt to disassemble the battery, remove any component projecting
from the battery terminals and do not dispose of in a fire.
• The battery and charger have no user serviceable parts. Fire or injury may result.
• Prior to disposal, protect exposed terminals with heavy insulating tape to prevent
shorting. The battery is to be disposed of safely at your local battery recycling
centre.
• When the battery pack is not in use, keep it away from other metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
• In case of battery leakages avoid any contact with the skin. If liquid comes into
contact with the skin, wash immediately with soap and water, then neutralise
with lemon juice or vinegar. If liquid gets into the eyes, ush with clean water
for at least 10 minutes, then seek immediate medical attention.
• To reduce the risk of re, personal injury, and product damage due to short
circuit, never immerse the tool, battery pack, or charger in uid or allow uid
to ow inside them. Corrosive or conductive uids, such as seawater, certain
industrial chemicals, and bleach or bleach-containing products, etc., can cause a
short circuit.
4

GENERAL INFORMATION
Technical Specications F18OPSV22Z F18OPSV22J2
Product Description Hoover ONEPWR Emerge
Cordless Vacuum
Hoover ONEPWR Emerge
Pet Cordless Vacuum
Console Model Number BH53600ANZV BH53602ANZV
Product Weight
(without battery pack)
2.8kg 3.09kg
Dust Cup Capacity 600ml 600ml
Runtime* Up to 45 mins Up to 45 mins
Charge Time (per battery) 3 hours 3 hours
Charger Model Number BH05000ANZ BH05000ANZ
Battery Included 1x 4.0Ah (BH29040ANZV) 1x 4.0Ah (BH29040ANZV)
Battery Voltage 18V Li-Ion 18V Li-Ion
Compatible Battery Packs
Subject to technical change without notice.
* Runtime is based on internal testing. Actual runtime will vary under specific
conditions or when using different accessories.
Description of Symbols
DISTRIBUTED BY:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC, 3149, Melbourne, Australia
Web Address: www.hoover.com.au
Customer Careline: 1300 698 130
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South, East Tamaki, Auckland, 2013, New Zealand
Web Address: www.hoover.co.nz
Customer Careline: 0800 126 688
Regulatory
Compliance
Mark
For Indoor
Use Only
Read User
Manual
5
MODEL TYPE RATED VOLTAGE RATED CAPACITY CELL NUMBER
F18BTOP21J4 Li-Ion 18V 4.0Ah 5
BH29040ANZ Li-Ion 18V 4.0Ah 5
BH29040ANZV Li-Ion 18V 4.0Ah 5

66
7
8
9
10
1Carry Handle
2Filter (hidden)
3Dirt Cup Release Button
4Dirt Cup
5Dirt Release Button (hidden)
6Handheld Crevice Tool (hidden)
7Power ON/OFF
8Reduce Suction
9Increase Suction
10 Battery Level Indicator Light
11 Reach Wand
12 Reach Wand Crevice Tool (hidden)
13 Floorhead with LED Lights
14 Brushbar
15 Battery Dock
16 ONEPWR 4.0Ah Battery
17 ONEPWR Charger
18 2-in-1 Dusting Brush/Crevice Tool
19 Upholstery Tool
20 Wall Mount, Screws and Wall Plugs
MODEL: F18OPSV22Z
Subject to technical change without notice. Images are illustrative only.
17
18 20
1
3
4
2
5
6
13
11
12
14
16
19
MACHINE OVERVIEW
15
EMERGE
CORDLESS VACUUM

SAFETY GUIDE
7
MACHINE OVERVIEW
EMERGE PET
CORDLESS VACUUM
7
8
9
10
1Carry Handle
2Filter (hidden)
3Dirt Cup Release Button
4Dirt Cup
5Dirt Release Button (hidden)
6Handheld Crevice Tool (hidden)
7Power ON/OFF
8Reduce Suction
9Increase Suction
10 Battery Level Indicator Light
11 Reach Wand
12 Reach Wand Crevice Tool (hidden)
13 All-Terrain Floorhead with LED Lights
14 Brushbar and Brushroll
15 Battery Dock
16 ONEPWR 4.0Ah Battery
17 ONEPWR Charger
18 2-in-1 Dusting Brush/Crevice Tool
19 Motorised Pet Tool
20 Wall Mount, Screws and Wall Plugs
Powered Extension Hose
MODEL: F18OPSV22J2
Subject to technical change without notice. Images are illustrative only.
17
18
20
1
3
4
2
5
6
13
11
12
14
16
19
15
21
21

8support.vax.co.uk
ASSEMBLING THE VACUUM
Fit the dirt cup onto the hooks, then rock
it up into the handheld so it secures
into place.
Push the reach wand down onto the
floorhead until it clicks into place.
Push the handheld down onto the reach
wand until it clicks into place.
ASSEMBLY
NOTE: The tool caddy attaches onto the reach wand. Accessories can be stored by sliding them onto the top and
bottom of the tool caddy.

9
ATTACHING THE WALL MOUNT
Choose the desired location, then place
the wall mount on the wall. Ensure that
the mount height allows the floorhead
to be positioned flat on the floor
when mounted. Mark the wall anchor
locations. Install the anchors and screw
the wall mount to the wall.
Store the vacuum by firmly pressing the
product into the wall mount to secure.
Accessories can be stored by sliding
them onto the top and bottom of the
wall mount.
NOTE: Vacuum can be locked into an upright position, but is not meant to be left standing unattended. While using
the vacuum in between uses or when carrying out any maintenance always lie the vacuum flat on the floor, in a
suitable location so it does not become a trip hazard or can be stepped on.
IMPORTANT: The wall mount is not designed to hold the full weight of the vacuum. The oorhead should be
positioned at on the surface of the oor to support the weight of the vacuum while the wall mount positions the
vacuum in the upright position.
ASSEMBLY

10 support.vax.co.uk
Once fully charged, slide the battery off
the charger to remove.
To check the battery charge
level press the battery symbol.
THIS MACHINE IS ONLY TO BE USED WITH HOOVER ONEPWR BATTERIES AND CHARGER.
PLEASE READ THE BATTERY AND CHARGER USER GUIDES BEFORE USE.
NOTE: Before first use, ensure the battery is fully charged. Failure to fully charge the battery before first use
may result in poor battery performance. The life expectancy of the battery will vary depending on the usage of the
machine.
CHARGING YOUR PRODUCT
CHARGING THE BATTERY
Plug in the charger. Attach the battery
pack to the charger by aligning the ribs
on the battery pack to the grooves in
the charger.
The charger light will flash white to
show when the battery is charging. The
light on the charger will stop flashing
and go off when the battery is fully
charged.

11
Place your foot on the floorhead. Pull the
handle backwards to recline.
To remove the battery press both the
buttons to release.
Slide the battery into the machine until it
clicks into place.
WARNING: The brushbar in the floorhead constantly rotates when activated. Never use the floorhead on one spot
for an extended period of time as the brushbar may damage the surface. To prevent any damage being sustained,
test on an inconspicuous area of the flooring/surface first.
CAUTION: Always take extra care when using the vacuum on the stairs.
OPERATION
•ON/OFF power button.
•Unit turns on in Default mode.
•To increase runtime for hard
oors and everyday messes.
•To increase suction for more
embedded messes.
•Battery LED is illuminated WHITE
when on and RED when battery
is low.
NOTE: Pressing the - or + will increase
or decrease the power level from where
it is currently running.
CAUTION: Store the vacuum
safely after use to prevent tripping
accidents.
CAUTION: Not to be used for
grooming a pet.
NOTE: When less than 20% charge
is remaining the low battery
indicator will flash red indicating the
battery is running low and charging
is required.
CAUTION: If the brushbar in the
floorhead has been obstructed, the
brushbar motor protection sensor
may activate. The brushbar will
stop and the machine may switch
off. To reset, switch the machine
off and remove the battery. Remove
the floorhead from the reach wand/
handheld and clear any obstruction.
Wait 1 minute before refitting the
floorhead. Install the battery and
switch the machine on.
During use, press the battery symbol on
the battery. The lights will illuminate
indicating how much charge is
remaining.
GETTING STARTED

12 support.vax.co.uk
2-in-1 Dusting Brush/Crevice Tool
1. Soft bristled dusting brush for delicate surfaces and skirting boards.
2a. For edge cleaning press the button and push the dusting brush down.
2b. For tight and hard to reach areas press the button and pull the dusting brush up
to remove it.
12a 2b
Motorised Pet Tool
While in use, the mini motorised base
plate can be rotated so it can be
used flat or horizontally for all angle
cleaning.
Press the release button on reach wand
and pull to separate.
GETTING STARTED
HANDHELD MODE
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before
connecting or disconnecting accessories.
Push the chosen accessory into the
handheld until it clicks into place.
Accessories can also be attached onto
the reach wand for cleaning up high.
Disconnect the floorhead and push the
accessory into the reach wand until it
clicks into place.
USING THE ACCESSORIES
NOTE: Motorised pet tool included
with model F18OPSV22J2 only.

13
Powered Extension Hose
Extends to reach confined spaces.
Powered for use with the motorised pet
tool and floorhead. Can also be used
with the upholstery and 2-in-1 dusting
brush/crevice tool.
USING THE ACCESSORIES
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before
connecting or disconnecting accessories.
Upholstery Tool
Ideal for cleaning surfaces such
as sofas, chairs, mattresses, and
cushions. For more delicate areas, the
brush attachment can be removed by
unclipping the attachment from the tool.
NOTE: All of the accessories,
including the 2-in-1 tool, upholstery
tool, motorised pet tool and
floorhead, can be attached directly
onto the handheld, reach wand or
powered hose.
The powered hose, crevice tool and
dusting brush can be used for hard
to reach places and at different
heights for above floor cleaning.
To remove the tools, press the
button on the tool and pull to
release.
GETTING STARTED
NOTE: Powered extension hose
included with model F18OPSV22J2
only.
NOTE: Upholstery Tool included
with model F18OPSV22Z only.

14 support.vax.co.uk
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before cleaning
or servicing.
IMPORTANT: Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from
various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove dirt, dust, oil,
grease, etc.
EMPTYING THE DIRT CUP
Press button to release the dirt cup. Hold the dirt cup over a bin and press
the dirt cup release button to empty.
Close the dirt cup, then replace it by
rocking it back into place.
CLEANING THE SEPARATOR
NOTE: For best cleaning results,
empty the dust cup after each use.
Lift the dirt cup cover to access the
filter. Lift the filter and separator from
the dirt cup.
Tap the separator over a bin to remove
dirt and debris and wipe over the
metal shroud with a dry cloth.
CLEANING AND MAINTENANCE

15
Refit the separator making sure that
the tabs on the separator fits into the
grooves on the dirt cup. Then refit the
dirt cup cover.
Pull the tab on the filter to remove from
the separator.
Tap the filter against the bin to remove
any dirt and debris.
Wash the filter under running water
(40°C max). Leave for at least 24hrs or
until fully dry before replacing.
24hr
40°C
MAX
CLEANING THE FILTER
CAUTION: Ensure that the filter,
dirt cup lid and separator are
refitted before use.
IMPORTANT: Don’t over ll the dust cup to avoid blocking the air ow through the vacuum cleaner. Do not exceed
the MAX line indicated on the side of the dust cup.
CLEANING AND MAINTENANCE
IMPORTANT: The lter should be tapped over a bin every 4-6 uses, to remove dirt and debris, and replaced every
6-9 months, depending upon use. The lter should be washed every 3 months, or when required. Allow the lter to
completely dry before reinstalling.

16 support.vax.co.uk
REMOVING AND CLEANING THE BRUSHBAR (MODEL F18OPSV22Z)
NOTE: If the brushbar in the floorhead has been obstructed, the brushbar motor protection sensor may activate.
The brushbar will stop and the machine may switch off. To reset, switch the machine off and remove the battery.
Remove the floorhead from the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting the
floorhead. Install the battery and switch the machine on.
CLEANING AND MAINTENANCE
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before cleaning
or servicing.
Remove the floorhead from reach wand.
Using your fingers or a coin, push and
turn the brushbar lock anticlockwise to
release the brushbar.
Pull the brushbar out of the floorhead
with pull tab.
To remove any threads or hair, cut along
the groove of the brushbar.
Refit the brushbar into the housing and
turn the brushbar lock clockwise to lock.
IMPORTANT: For best
performance, regularly remove
any threads or hair from around
the brushbar.

17
REMOVING AND CLEANING THE BRUSHBAR
(MODEL F18OPSV22J2)
NOTE: If the brushbar or brushroll in the floorhead has been obstructed, the motor protection sensor may activate.
The brushes will stop and the machine may switch off. To reset, switch the machine off and remove the battery.
Remove the floorhead from the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting the
floorhead. Install the battery and switch the machine on.
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before cleaning
or servicing.
Remove the floorhead from reach wand.
Using your fingers or a coin, push and
turn the brushbar lock anticlockwise to
release the brushbar.
Pull the brushbar out of the floorhead
with pull tab.
To remove any threads or hair, cut along
the groove of the brushbar.
Refit the brushbar into the housing and
turn the brushbar lock clockwise to lock.
IMPORTANT: For best
performance, regularly remove
any threads or hair from around
the brushbar.
CLEANING AND MAINTENANCE

18 support.vax.co.uk
REMOVING AND CLEANING THE BRUSHROLL
(MODEL F18OPSV22J2)
NOTE: If the brushbar or brushroll in the floorhead has been obstructed, the motor protection sensor may activate.
The brushes will stop and the machine may switch off. To reset, switch the machine off and remove the battery.
Remove the floorhead from the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting the
floorhead. Install the battery and switch the machine on.
CLEANING AND MAINTENANCE
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before cleaning
or servicing.
Refit the brushroll into the housing and
turn the brushroll lock clockwise to
lock.
Using a coin, push and turn the brushroll
lock anticlockwise to unlock the
brushroll.
Lift and rotate the brushroll away from the
floorhead assembly.
Clear debris from the brushroll with a dry
cloth. Clear any dirt/debris from the end
caps of the powered nozzle.
IMPORTANT: For best
performance, regularly remove
any threads or hair from around
the brushroll.

SAFETY GUIDE
19
Pull the brushbar out from the brushbar
housing.
Using a coin, turn the brushbar lock
anticlockwise to release the brushbar.
To remove any threads or hair slide
the blade of a pair of scissors into the
groove on the brushbar and cut along
the groove. Clear any dirt/debris inside
the housing of the tool.
NOTE: If the brushbar in the motorised pet tool has been obstructed, the brushbar motor protection sensor may
activate. The brushbar will stop and the machine may switch off. To reset, switch the machine off and remove the
battery. Remove the tool and clear any obstruction. Wait 1 minute before refitting the tool. Install the battery and
switch the machine on.
Check the inlet for any blockages
and use a blunt object to remove the
blockage.
Refit the brushbar and turn the
brushbar lock clockwise to lock.
REMOVING AND CLEANING THE MOTORISED PET TOOL BRUSHBAR
(MODEL F18OPSV22J2)
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before cleaning
or servicing.
CLEANING AND MAINTENANCE

20 support.vax.co.uk
CHECKING FOR BLOCKAGES
Remove the dirt cup and reach wand.
Check and clear any dirt and debris from
the dirt cup and handheld inlet.
Press the dirt cup release button and
remove the dirt cup. Check and clear
any dirt and debris from behind the dirt
cup flap.
Check the powered floorhead for any
blockages and use a blunt object to
remove the blockage.
To test for a blockage in the reach wand or powered hose, drop a small ball of paper
into the wand/hose. The paper will drop through if the wand/hose is clear. Use a
broom handle or similar blunt object to remove any blockage.
CLEANING AND MAINTENANCE
WARNING: To reduce the risk of personal injury, always turn power switch off and remove battery before cleaning
or servicing.
NOTE: Powered extension hose
included with model F18OPSV22J2
only.