Hoover 5006PH Mode User manual

Bagged Vacuum
Cleaner with Powerhead
Compact Powerhead
for a Powerful Clean
Washable HEPA Filtration
High Efficiency Soft Start Motor

Features
3.
Features:
1. Handle
2. Hose
3. Air Outlet
4. Handle Release Button
5. Telescopic Tube
6. Powerhead
7. Handle
8. Cover Release Button
9. Accessories Storage Compartment
10. Exhaust Filter Grill
11. On/Off Button
12. Variable Speed Dial
13. Automatic Cable Retract Button
14. Power Cable & Plug (not shown)
15. Powerhead Release Button
Specifications:
Max Watts: 1500W + 100W =1600W
Dust Capacity: 2.5L
Noise Level: <73dBa
Hose Length: 1.9m
Telescopic Tube: Aluminium
Power Cable Length: 5m
Weight: 8.2kg
Accessories: (not shown)
Combination Floor Brush
Crevice Tool
Upholstery Brush
Dusting Brush
Hand Turbo Brush
Please contact Hoover Customer Care 1300 360 845,
NZ [phone] to find your local spare parts provider.
5006PH Mode
Congratulations on the purchase of your new HOOVER vacuum cleaner. There are many useful
features built into your cleaner and we recommend that you carefully read this instruction manual
so that you may take best advantage of them.
2.
2
6
1
3
4
5
13
12
14
8
7
10 11
9
15

Before you Begin
5.4.
Before you Begin
When using your vacuum cleaner, basic
precautions should always be observed, including
the following;
1. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
2. Children should be supervised to ensure that
they do not play with the appliance.
3. To prevent electrical shock, do not immerse
the appliance, power cord or power plug into
water or other liquids.
4. To prevent electrical shock, do not use the
vacuum cleaner outdoors or on wet surfaces.
5. Always check the power cord before use, the
power cord and the plug should be in a good
condition and must not be damaged. If the
power supply cord is damaged or defective,
it must be replaced by the manufacturer, its
service agent or similarly qualified person in
order to avoid a hazard.
6. Do not unplug by pulling on the power cord.
To unplug, grasp the plug not the power cord.
Use only Australian and New Zealand electrical
safety approved extension cords.
7. Do not pull or carry the appliance by the power
cable, use the power cable as a handle or
pull the power cable around shaft edges or
corners. Avoid running the appliance over the
power cable.
8. Ensure the appliance is switched off before
unplugging.
9. Do not handle or operate the appliance
with wet hands and follow electrical safety
precautions at all times.
10. Extreme caution should be exercised when
using the appliance on stairs.
11. Do not attempt to change the attachments
while the appliance is plugged in to mains
power supply. Switch off and remove plug from
mains power supply. Use only manufacturer’s
recommended accessories.
12. Do not operate the vacuum cleaner too close
to the heaters, radiators and other
hot surfaces.
13. Do not use the appliance to pick up flammable
items or combustible liquids (i.e. petrol, hot
ashes cigarettes, matches, explosive materials
or anything burning) or use in areas where
such substances and items may be present.
14. Do not use the appliance to pick up toxic
materials (i.e. chlorine bleach, ammonia).
15. Ensure the appliance is disconnected from the
mains power supply before connecting the
hose to the unit.
Safety Precautions & Warnings
IMPORTANT! Always switch off the cleaner and remove the plug from the
electricity power supply before cleaning your appliance, when not in use or
attempting any maintenance task. The cleaner must only be connected to an
AC power supply at the voltage shown on the rating label. This cleaner should
only be used for its intended purpose as described in this instruction manual.
Never operate the vacuum cleaner without filters.
This cleaner must be operated in accordance with these instructions and used only for domestic
household cleaning to remove DRY dirt and dust from household carpets, flooring, walls and fabrics.
This cleaner is not fit to be used as an industrial cleaner hence will void the manufacturer’s warranty if
used inappropriately.
Please read these instructions thoroughly
This will ensure you obtain full benefit from your new cleaner. Keep this Instruction Manual in a handy
place for future reference.
Important
Always switch the cleaner off and remove the plug from the electricity supply before cleaning your
appliance, when not in use, or attempting any maintenance task. The cleaner must only be connected to
an AC supply at the voltage shown on the rating plate. This cleaner should only be used for its intended
purpose as described in these instructions.
Precautionary measures:
1. Do not operate the vacuum cleaner too close to heaters, radiators, and other
hot surfaces.
2. Before inserting the plug into the wall, make sure your hand is dry.
3. Before turning on the vacuum cleaner, remove any large or sharp objects from the
floor or cleaning surface in order to prevent damage to the filter.
4. When you want to pull the plug from the wall, do not use the power cable, gently
pull the plug from the power socket.
5. Do not use vacuum cleaner to pick up water or liquids.
This vacuum cleaner is equipped with a plug and a cable, which rewinds automatically. If anything gets
damaged, both the plug and the cable must be repaired by a qualified technician.

Warnings
7.6.
16. Do not operate or use the appliance without the
dust bag and/or filters in place.
17. Before vacuuming, remove any large or sharp
objects from the floor or cleaning surface in order
to prevent damage to the filter.
18. If the air inlet, floor head or the telescopic tube
is blocked, switch off the cleaner straight away
and remove from the mains power. First clear
the blocked object before attempting to start the
cleaner vacuum again.
19. Hold the plug when rewinding onto the cord reel.
To prevent accidental injury do not allow the plug
to whip when rewinding.
20. Do not extend the power cable beyond the
yellow mark.
21. Do not leave the appliance unattended when it is
connected to a mains power supply.
22. Before carry out any maintenance service
or cleaning the filters, always switch off the
vacuum cleaner and disconnect the plug
from power supply.
23. Keep ends of the hose, telescopic tube and
other openings away from your face and body.
24. Do not use the vacuum cleaner if it is damaged
or breaks down. Check the electrical regularly
for defects. If connection cables, electrical
hoses, electrical contacts and electric tubes are
damaged, have them replace immediately.
25. Never clean the vacuum cleaner or any of
the electrical parts, especially the electrical
connections with water or liquid cleaners.
26. Never attempt to make any modifications
electrically to the vacuum cleaner.
27. Always store the appliance indoors in a cool
and dry place.
28. Do not pick up water, dry household use only.
29. Damage caused by improper use or by not
observing the instructions in this manual will
void warranty.
Vacuum Cleaner with Power Head
1. The electric hose contains electrical connections;
- Do not immerse it in water for cleaning;
- The hose should be checked regularly and
must not be used if damaged.
- The vacuum cleaner handle contains
electrical connections the handle is not a
serviceable part
- The vacuum cleaner rod contains electrical
connections the rod is not a serviceable part
- The vacuum cleaner powerhead contains
electrical connections the powerhead is not
a serviceable part
2. Use the electric power head only for vacuuming
dust and dry substances in the home.
3. Never run over the power cable with the power
head as the cable could get damaged.
4. Never touch the brush roller while the vacuum
cleaner is connected to the mains.
5. To prevent unnecessary wear on the power
head cleaning nozzle keeps it moving while
in operation.
Safety Precautions & Warnings Assembling the Vacuum Cleaner
IMPORTANT! Always remove the plug from the power socket before fitting
or removing accessories.
1. Fitting or Removing the Flexible Hose
Fitting:
Insert the flexible hose into the air inlet of the vacuum. Press until it
clicks into position.
Removing:
Remove the plug from the power socket and then release the flexible
hose from the air inlet by depressing the two buttons.
b. Fit the floor head to the telescopic tube, gently insert the
telescopic tube into the floor head and push until it clicks
in place.
You will hear the click sound.
2. Fitting the Telescopic Tube
and Accessories
Important: Ensure the powerhead switch on the handle is
in the “off” position before fitting the handle to the tube.
a. Fit the telescopic tube to the handle, gently insert the handle
into the telescopic tube and push until it clicks in place.

Assembly
9.8.
Assembling the Vacuum Cleaner
Ideal for picking up pet hair on upholstery.
Note: The hand turbo brush adaptor must be used to fit the telescopic
tube to the accessory.
1. Insert the smaller end of the adaptor into the end of the hand turbo brush.
2. Insert the larger end of the adaptor into your handle or telescopic rod.
3. The hand turbo tool is now ready to be used with the vacuum.
Note: Unlock the side release buttons by sliding them up or down as
required. This will allow you to rotate the rubber external bristle to face
upwards, allowing a closer clean as required.
Hand Turbo Brush
Combination Floor Head: For use on hard
floors and carpet.
Powerhead: For use on carpet for a deep clean.
Crevice tool: For radiators, crevices, corners,
baseboards and between cushions.
Upholstery tool: For vacuuming furniture
and upholstery.
Dusting brush: For furniture, blinds, bookshelves
and lamp shades.
Hand Turbo Tool: For removing pet hair and dirt
from upholstery and bedding.
Accessories
Ideal for daily cleaning on carpets
and hard floors*.
*Powerhead is NOT ideal for
hard floors
Carpet Hard Floors*
Instructions for Use
Before using the appliance, unwind a sufficient length of cable and insert the
plug into the power socket. A yellow mark on the power cable shows the ideal
cable length. Don’t expend the cable beyond the red mark.
1. Press the ON/OFF button to turn the vacuum on.
2. To rewind the power cable, press the retract button
with one hand and guide the cable with the other hand
to ensure that it does not whip causing damage to
the cable.
3. Press the ON/OFF button on the handle to operate
the powerhead.
On/Off
button

Maintenance
11.10.
Maintenance
IMPORTANT! Ensure the vacuum cleaner is not connected to the power supply
when performing any maintenance procedures. Use a damp cloth and mild
detergent when cleaning the appliance.
Vacuum Cleaner Storage
When not in use, ensure the cleaner is not connected to the power supply, and pull the power cable
gently out of the power socket. Press the automatic cord rewind button to reel in the power cable fully.
Hang the floor brush onto the floor park. The powerhead must be stored separately. Store the cleaner
in a cool dry location.
Changing the Dust Bag
Always operate the cleaner with dust bag installed. If you
forget to attach the dust bag or attach it in the wrong
direction, the dust bag cover may not close completely.
1. Remove the hose from the inlet.
2. Open the cover.
3. Remove the dust bag holder and dust bag from
the machine.
4. Remove the dust bag when it is full and replace bag
by sliding a new dust bag into the bag holder in the
direction of the arrow.
5. Replace the bag holder and bag into the machine.
6. Gently close the cover, you will hear it click closed.
Motor Filter Replacement
WARNING! Ensure the cleaner is not connected to the power supply when
performing any maintenance procedure.
• The inlet filter should be cleaned at least twice a year or
when it becomes visibly dirty.
• Always operate the cleaner with all clean filters installed.
Otherwise, suction power is reduced or motor damage
may be result.
• Do not use a washing machine to wash the inlet filter.
• Do not use hair drier to dry clean the filter.
1. Pull out the filter bracket assembly.
• Separate the filter from the bracket assembly.
• Replace with a new filter and reinstall the filter bracket
back in the vacuum.
Exhaust Filter Cleaning or Replacement
1. Open the dust bag cover and remove the exhaust filter.
2. Clean the filter with lukewarm water (no soap) and allow
24 hours to air dry before reinstalling.
3. It is recommended to replace the exhaust filter every
6 months.

Maintenance
13.12.
Maintenance (continued)
Hand Turbo Brush
Warning: Ensure the cleaner is not connected to the mains power supply when
performing any maintenance procedures.
1. Unlock the neck on the hand turbo brush by twisting anti-clockwise.
2. Push the release buttons on the side of the Hand Turbo Brush down to unlock the external
bristles. Rotate this bristle attachment upwards.
3. Remove the clear cover.
4. Remove any dirt or hair from the roller brush.
5. Replace the clear cover.
6. Lock the neck on the hand turbo brush by twisting clockwise.
7. Rotate the external bristles down and lock the side release buttons by pushing upwards.
Changing the Motorised Powerhead Drive Belt
WARNING: To reduce the risk of electric shock, turn all power off from the unit and
unplug the unit before performing any cleaning, maintenance or troubleshooting
checks. Failure to do so may result in electric shock or personal injury.
Depending on how much your vacuum is
used, the motorised powerhead drive belt will
occasionally require changing.
1. Disconnect the powerhead from the
telescopic tube.
Cleaning the Motorised Powerhead
The rotating brush must be free of debris for effective cleaning
and maximum suction. Disconnect the motorised powerhead
and turn it over to inspect the bottom. If a buildup of debris is
wound around the rotating brush, remove by carefully cutting
with scissors. Avoid damaging or cutting the bristles.
2. Turn the powerhead upside down and
remove the small screw from the centre of
the powerhead.
3. Release the 4 clips from the underside,
allowing you to remove the bottom plate.

Maintenance
15.14.
Maintenance (continued)
Part Part Number
Filter Set 32200832
Bag Holder 33101201
Dust Bag 5Pk 32410222
Hose Assembly 31210073
Rod 31300564
Troubleshooting
Problems and Solutions
If you come across a problem, please use the checklist of troubleshooting tips before
ringing Hoover Customer Care.
Fault Solutions
The cleaner will not turn on. Check that the power cable is inserted securely; remove from the
power supply and then reinsert into the power supply.
Check that the on/off switch is in the “ON” position.
The vacuum performance
is deteriorating.
Check the appliance to ensure there are no blockages.
Clear any blockages that may be found.
Check that the air-inlet filter is not dusty; frequently clean rubbish or
replace air-inlet and air-outlet HEPA filters every 6 months.
The cleaner makes an
abnormal sound when
switched on.
Turn off the cleaner immediately.
Check the appliance to ensure there are no blockages.
Please clear any blockages that may be found.
Light on suction control dial is
illuminated or flashing.
This can be caused by a full dust bag or blockage within the hose
or rod.
Please contact Hoover Customer Care: 1300 360 845, NZ: [phone] to find your
local spare parts provider.
5. Slide the old belt off the drive shaft and then the end cap.
If the belt is broken, remove all the broken pieces.
6. Place the new belt over the drive shaft first and then the end
cap. Make sure the lettering on the belt is on the outside.
Insert the end cap into the groove.
7. Holding the rotating brush, insert it into the end cap first
and then into the groove on the other side.
8. Replace the bottom plate.
Changing the Motorised Powerhead Drive Belt (continued)
End Cap
4. First lift up the end of the rotating brush with no belt
and remove it. Then lift the end cap where the belt
loops around.

Conditions of warranty
Your Hoover cleaner, in the case of domestic use, has a two year
parts and labour warranty against product defects and failures when
the product is used in accordance with the terms and conditions of
this warranty statement.
This warranty commences from the original date of purchase and is
not transferable; please retain your original proof of purchase for any
warranty claims. This warranty is valid only in the country where the
cleaner is purchased.
The cleaner must be operated in accordance with these instructions
and used only for domestic household cleaning to remove DRY dirt
and dust from household carpets, flooring and fabrics. This cleaner
is not fit to be used as an industrial cleaner, and is not designed for
the collection of vitreous building material including particle board,
construction products and similar products such as wood/fibres,
cement, fillers, fibre glass etc or excessive or frequent sand. The
infrequent pick-up of these materials in these circumstances may be
harmful to your cleaner and may void the manufacturer’s warranty.
Accessories and consumables including dust bags and filters,
unless defective in manufacture, are not subject to this warranty. In
order to prolong the life of accessories and consumables, regular
care and maintenance is recommended.
When properly used and cared for, your cleaner will render excellent
service; refer to the instruction manual for further details, as misuse
or failure to follow the instructions makes this warranty void.
In the event of service or advice being needed, please contact
Hoover Floorcare Asia Pacific Pty Ltd, Level 1, Building 2 Brandon
Business Park, 530 Springvale Road, Glen Waverley Victoria 3150,
or on 1300 360 845, Monday-Friday 9am-5pm EST. The decision
to repair or replace the cleaner is at the sole discretion of Hoover
Floorcare. If Hoover Floorcare decide to repair or replace the cleaner,
it will do so at its own cost.
Hoover Floorcare is unable to accept responsibility under this
warranty for any repair work not carried out by an authorised Hoover
Service Agent or from the use of non-genuine parts. If any part is
no longer available or manufactured, Hoover Floorcare will replace it
with a genuine functional replacement part. This warranty does not
apply to the cost of replacing any parts of the product due to normal
wear and tear, alterations, improper installation, physical abuse,
misuse or accidental damage. Any transportation costs involved in
the repair of defective parts shall be borne by the claimant.
If proof of purchase cannot be provided at the time of a warranty
claim or service, any work carried out on the cleaner is chargeable.
The repair or replacement of the cleaner under this warranty does
not extend the original period of warranty.
The benefits conferred by this warranty are in addition to all other
rights and remedies in respect of the product as outlined under the
Competition and Consumer Act and other State and Territory laws.
“Our goods come with guarantees that cannot be excluded in
the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.”
Call Hoover Floorcare
with any product queries
Australia 1300 360 845
New Zealand [phone]
To find out more about our range,
visit: www.hoover.com.au
www.hoover.co.nz
email: sales@hooverfloorcare.com.au
V1 12 /14
mode
Bagged Vacuum
Cleaner with Powerhead
SAVE TIME, REGISTER WARRANTY ONLINE!
www.hoover.com.au and www.hoover.co.nz