Hoover DWOL 410AHR/1-AUS User manual

EN
DWOL 410AHR/1-AUS

!
2
Thank-you for choosing a Hoover washing
machine. We are proud to always offer
new, innovative and technologically
advanced products, with a complete range
of home appliances to ensure true
assistance in your daily routine.
Carefully read this manual for correct and
safe appliance use and for helpful tips on
efficient maintenance.
Only use the washing machine
after carefully reading these instructions.
We recommend you always keep this
manual on hand and in good condition for
any future owners.
Please check that the appliance is
delivered with this instruction manual,
warranty certificate, water and energy
efficiency label. Also check that plugs,
curve for drain hose and liquid detergent or
bleach tray (only on some models) are
included. We recommend you keep all
these components.
Each product is identified by a unique 16-
character code, also called the “serial
number”, printed on the sticker affixed to
the appliance (porthole area) or in the
document envelope found inside the
product.
This appliance is marked according to
the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components (which can
be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials. Individuals can
play an important role in ensuring that WEEE
does not become an environmental issue; it is
essential to follow some basic rules:
!WEEE should not be treated as household
waste;
!WEEE should be handed over to the relevant
collection points managed by the municipality or
by registered companies. In many countries, for
large WEEE, home collection could be present.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
1. GENERAL SAFETY RULES
2. INSTALLATION
3. PRACTICAL TIPS
4. MAINTENANCE AND CLEANING
5. QUICK USER GUIDE
6. CONTROLS AND PROGRAMS
7.
THROUBLESHOOTING AND WARRANTY
Environmental conditions
Contents

!
EN
3
1. GENERAL SAFETY
RULES
!This appliances is intended to
be used in household and
similar applications such as:
- Staff kitchen areas in shops, offices
and other working environments;
- Farm houses;
- By clients in hotels, motels and
other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
! This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities,
or lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use of
the appliance by a person
responsible for their safety.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
!Children should be supervised
to ensure that they do not play
with the appliance.
!Children of less than 3 years
should be kept away unless
continuously supervised.
!If the supply cord is damaged, it
must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
!Only use the hose-sets
supplied with the appliance for
the water supply connection
(do not reuse old hose-sets).
! Water pressure must be between
0,05 MPa and 0,8 MPa.
!Make sure that carpet does not
obstruct the base of the machine
and ventilation openings.
!The OFF condition is reached
by placing the reference mark on
the programmes control/knob in
the vertical position. Any other
different position of such control
sets the machine in ON condition
(only for models with programmes
knob).

!
4
!After installation, the appliance
must be positioned so that the
plug is accessible.
!The maximum load capacity of
dry clothes is 10 kg.
!The technical details (supply
voltage and power input) are
indicated on the product rating
plate
!Make sure that the electrical
system is grounded, complies
with all applicable law and that
the (electricity) socket is
compatible with the plug of the
appliance. Otherwise, seek
qualified professional assistance.
!The use of converters, multiple
sockets or extension cords is
strongly advised against.
!Before cleaning or maintaining
the washing machine, unplug
the appliance and turn off the
water faucet.
!Do not pull on the power cord
or appliance to unplug the
machine.
!Make sure there is no water in
the drum before opening the
porthole.
!Do not expose the washing
machine to rain, direct sunlight
or other weather elements.
Protect from possible freezing.
!When moving, do not lift the
washing machine by the knobs
or detergent drawer; during
transport, never rest the
porthole on the trolley. We
recommend two people lift the
washing machine.
!In the event of fault and/or
malfunction, turn off the
washing machine, close the
water faucet and do not tamper
with the appliance.
Immediately contact the
Customer Service Centre and
only use original spare parts.
Failure to observe these
instruction may jeopardise
appliance safety.
Electrical connections and
safety instructions
WARNING:
water may reach very high
temperatures during the
wash cycle.

!
EN
5
2. INSTALLATION
!Unscrew the 2or 4transit
screws (A) on the back and
remove the 2or 4washers (B)
as illustrated in figure 1.
!Close the 2or 4holes using the
plugs included in the instruction
envelope.
!In some models, 1or more
washers will fall inside the machine:
tilt the washing machine forward to
remove them. Close the holes using
the plugs found in the envelope.
Keep the transit screws & parts
for future use in case you move
house.
!Place the polionda sheet on the
bottom as shown in figure 2
(according to the model,
consider version A, Bor C).
A
A
A
A
B
B
B
B
1
3
2
1
3
1
2
A
C
B
2
WARNING:
keep packaging materials
away from children.
In some models this operation
will not be necessary, because
the corrugated plastic sheet
will be already placed on the
bottom of the appliance.

!
6
!Connect the water hose to the water
supply faucet (fig. 3) only using the hose
supplied with the appliance (do not
reuse old hose-sets).
!Some models may include one or more of
the following features:
!HOT&COLD (fig. 4):
water mains connection settings with hot
and cold water for higher energy savings.
Connect the grey hose to the cold water
faucet and the red one to the hot water
faucet. The machine can be connected to
the cold water faucet only: in this case, some
programs may start a few minutes later.
!AQUASTOP (fig. 5):
a device located on the supply hose that
stops water flow if the tube deteriorates;
in this case, a red mark will appear in the
window “A” and the hose must be
replaced. To unscrew the nut, press the
one-way lock device "B".
!AQUAPROTECT – SUPPLY HOSE WITH
GUARD (fig. 6):
Should water leak from the primary
internal hose "A", the transparent
containment sheath "B" will contain water
to permit the washing cycle to complete.
At the end of the cycle, contact the
Customer Service Centre to replace the
supply hose.
!The washing machine should be installed
in its final position such that the water fill
hose is not kinked or trapped. The
corrugated drain hose should be inserted
into a suitable drain pipe that is at a
height between 50 cm and 85 cm above
the floor using the curved drain hose
support. If an under sink connection is
used the drain hose must be routed
above the sink overfill opening to prevent
back siphoning. Care must be taken to
avoid kinking or trapping the drain hose
(fig. 7).
3
1
4
B
A
5
B
A
6
min 50 cm
max 85 cm
+2,6 mt
max
max 100 cm
min 4 cm
7
Water connections
Setting

!
EN
7
!Level the appliance using the feet as
illustrated in figure 8:
a. turn the nut clockwise to release the
screw;
b. rotate the foot to raise or lower it until it
adheres to the floor;
c. lock the foot, screwing in the nut, until it
adheres to the bottom of the washing
machine.
!Plug in the appliance.
A
B
C
8
The detergent draw is split into 3
compartments as illustrated in figure 9:
!compartment "1": for prewash detergent;
!compartment “ ”: for special additives,
softeners, starch fragrances, etc.;
!compartment "2": for washing detergent.
A liquid detergent cup is also included in
SOME MODELS (fig. 10). To use it, place it
in
compartment "2". The cup can also be
used for bleach when the “Rinse” program is
selected.
9
1
2
10
1
2
WARNING:
contact the Customer Service Centre
should the power cord need replacement.
Detergent drawer
WARNING:
Some liquid detergents are hard to
dissolve. In this case we recommend
diluting the detergent with warm water.
We recommend you use only 20% of
the recommended detergent quantities
shown on the detergent pack.
WARNING:
installation faults are not covered by
the manufacturers warranty.

!
8
3. PRACTICAL TIPS
WARNING: when sorting laundry,
make sure:
- there are NO foreign objects such as
coins, hair clips, pins, keys etc, etc, from
the wash load. Check all pockets. Serious
damage to the machine can result which
may not be covered by warranty.
- to have buttoned pillow cases, closed
zips, tied loose belts and long robe
ribbons;
- to have removed rollers from curtains;
- to have carefully read clothing washing
labels;
- to have removed any persistent stains
using specific detergents.
!When washing rugs, bedcovers or other
heavy clothing, we recommend you avoid
spinning.
!To wash wool, make sure the item can be
machine washed. Check the fabric label.
A guide to environmentally friendly and
economic use of your appliance.
Maximise The Load Size
!Achieve the best use of energy, water,
detergent and time by using the
recommended maximum load size.
Save up to 50% energy by washing a full
load instead of 2 half loads.
Do you need to pre-wash?
!For heavily soiled laundry only!
SAVE detergent, time, water and
between 5 to 15% energy consumption
by NOT selecting Prewash for slight to
normally soiled laundry.
Is a hot wash required?
!Pretreat stains with stain remover or soak
dried in stains in water before washing to
reduce the necessity of a hot wash
programme.
Save up to 50% energy by using a 60°C
wash programme.
Before using a drying programme
(WASHER-DRYERS)
!SAVE energy and time by selecting a
high spin speed to reduce the water
content in laundry before using a drying
programme.
Following is a quick guide with tips and
recommendations on detergent use at the
various temperatures. In any case, always
read the instructions on the detergent for
correct use and doses.
Load tips
Helpful suggestions for the user
When washing heavily soiled whites,
we recommend using cotton
programs of 60°C or above and a
normal washing powder (heavy duty)
that contains bleaching agents that at
medium/high temperatures provide
excellent results.
For washes between 40°C and 60°C
the type of detergent used needs to be
appropriate for the type of fabric and
level of soiling.
Normal powders are suitable for “white”
or colour fast fabrics with high soiling,
while liquid detergents or “colour
protecting” powders are suitable for
coloured fabrics with light levels of
soiling.
For washing at temperatures below
40°C we recommend the use of liquid
detergents or detergents specifically
labeled as suitable for low temperature
washing.
Please note - dilute viscous liquid
detergent with warm water if necessary.
For washing wool or silk, only use
detergents specifically formulated for
these fabrics.

!
EN
9
4. MAINTENANCE AND
CLEANING
To clean the washing machine exterior, use
a damp cloth, avoiding abrasives, alcohol
and/or solvents. The washing machine does
not require any special care for ordinary
cleaning: clean drawer compartments and
the filter; some tips on how to move the
machine or on long periods of disuse are
provided below.
!We recommend you clean the drawer to
avoid accumulating detergent and
additive residue.
!To do this, extract the drawer using slight
force, clean it with running water and
reinsert it in its housing.
!The washing machine comes with a
special filter able to trap large residue,
such as buttons or coins, which could
clog the drain.
!ONLY AVAILABLE ON CERTAIN MODELS:
pull out the corrugated hose, remove the
stopper and drain the water into a container.
!Before unscrewing the filter, we
recommend you place an absorbent cloth
under it to keep the floor dry.
!Turn the filter counter-clockwise.
!Remove and clean the filter; when
finished, replace it turning it clockwise.
!Repeat the previous steps in reverse
order to reassemble all parts.
!If the washing machine will not be used
for an extended amount of time and will
be store in a cold area ensure all water is
drained from the hoses to prevent
freezing.
!Unplug the washing machine.
!Detach the hose from the strap and lower
it, fully draining water into a bowl.
!Secure the drain hose with the strap
when finished.
Drawer cleaning
Filter cleaning
Suggestions for moves or
prolonged disuse
WARNING:
unplug the machine prior to cleaning.

!
10
5. QUICK USER GUIDE
This washing machine automatically adjusts
the level of the water to the type and
quantity of washing. This system gives a
reduction in energy consumption and a
saving in washing times.
!Turn on the washing machine and select
the required program.
!Adjust the washing temperature if
necessary and press the required "option"
buttons.
!Press the START/PAUSE button to start
washing.
Should power go out when the washing
machine is running, a special memory
saves the settings and, when power
returns, the machine resumes the cycle
from where it left off.
!At the end of the programme, the
message "End" will appear on the display
or, on some models, all wash stage
indicator lights will turn on.
!Turn off the washing machine.
For any type of wash, see the program
table and follow the operating sequence
as indicated.
Water pressure:
min 0.05 Mpa / max 0.8 Mpa
(0.05 MPa dispenses approximately 1 litre
of water in 10 seconds)
Spin r.p.m.: See rating plate.
Power input / Power current fuse amp /
Supply voltage: See rating plate.
6. CONTROLS AND
PROGRAMS
B
HGILMNE
C
OPF
D
Q
A
A
Programme selector with OFF
position
B
START/PAUSE button
C
SPIN SPEED button
D
TEMPERATURE SELECTION
button
E
DELAY START button
F
RAPID / STAIN /SOIL LEVEL button
G
PREWASH button
H
HYGIENE PLUS button
I
EXTRA RINSE button
L
STEAM button
M
FAVOURITES button
N
NIGHT & DAY button
O
Digital display
P
DOOR LOCKED indicator light
E+N
KEY LOCK
Q
ONE Fi EXTRA area
Program selection
Wait until the DOOR LOCKED light has
gone out before opening the door.
Technical data

!
EN
11
!
Press the START/PAUSE button to start
the selected cycle.
!
Once a programme is selected the
programme selector remains stationary on
the selected programme until the cycle ends.
!
"End" will appear in the display at the
end of the program and the DOOR
LOCKED light will go off, it is now
possible to open the door.
!
Switch off the washing machine by
turning the selector to OFF.
!Press to start the selected cycle.
ADD OR REMOVE ITEMS AFTER THE
PROGRAMMES HAS STARTED (PAUSE)
!Press and hold the START/PAUSE
button for about 2 seconds (some
indicator lights and the time remaining
indicator will flash, showing that the
machine has been paused).
!Wait until the DOOR LOCKED light has
gone out before opening the door.
!After you have added or removed items,
close the door and press the
START/PAUSE button (the programme
will start from where it left off).
CANCELLING THE PROGRAMME
!
To cancel the programme, set the
selector to the OFF position.
!Wait 2 minutes until the safety device
unlocks the door.
WARNING:
Don’t touch the display while inserting
the plug because the machines
calibrates the systems during the first
seconds: touching the display may
prevent the machine from working
properly. In this case, remove the plug
and repeat the operation.
PROGRAMME selector with OFF
position
When the programme selector is turned
the display lights up to show the settings
for the programme selected.
For energy saving, at the end of the
cycle or with an inactivity period, the
display level contrast will decrease.
N.B.: To switch the machine off, turn
the programme selector to the OFF
position.
The programme selector must be
returned to the OFF position at the end
of each cycle or when starting a
subsequent wash cycle prior to the next
programme being selected and started.
START/PAUSE button
Close the door BEFORE selecting the
button START/PAUSE.
When the START/PAUSE button has
been pressed, the appliance can take
few seconds before it starts working.
Before you open the door, please
check the water level is below the
door opening to avoid flooding.

!
12
!By pressing this button, it is possible to
reduce the maximum speed, and if you
wish, the spin cycle can be cancelled.
spin speed cancelled.
!If the label does not indicate specific
information, it is possible to use the
maximum spin expected in the program.
!To reactivate the spin cycle press the
button until you reach the spin speed you
would like to set.
!It is possible to modify the spin speed
without pausing the machine.
!
This button allows you to change the
temperature of the wash cycles.
cold wash.
!It is not possible to raise the temperature
over the maximum allowed for every
programme, in order to save the fabrics.
!
This button allows you to pre-programme
the wash cycle and delay the start of the
cycle for up to 24 hours.
!
To delay the start use the following
procedure:
- Set the required programme.
- Press the button once to activate it (h00
appears on the display) and then press
it again to set a 1 hour delay (h01
appears on the display). The pre-set
delay increases by 1 hour each time the
button is pressed, until h24 appears on
the display, at which point pressing the
button again will reset the delay start to
zero.
- Confirm by pressing the START/PAUSE
button (the light on the display starts to
flash). The countdown will begin and
when it has finished the programme will
start automatically.
!
It is possible to cancel the delay start by
turning the programme selector to OFF.
If there is any break in the power supply
while the machine is operating, a special
memory stores the selected programme
and, when the power is restored, it
continues where it left OFF
The option buttons should be selected
before pressing the START/PAUSE
button.
If an option is selected that is
not compatible with the selected
programme then the option indicator
first flashes and then goes off.
SPIN SELECTION button
To prevent damage to the fabrics, it is
not possible to increase the speed
over the maximum allowed for the
programme.
An over dosing of detergent can cause
excessive foaming. If the appliance
detects the presence of excessive foam,
it may exclude the spinning phase or
extend the duration of the program
and increase water consumption.
The machine is fitted with a special
electronic device, which prevents the
spin cycle should the load be
unbalanced. This reduces the noise
and vibration in the machine and so
prolongs the life of your machine.
TEMPERATURE SELECTION button
DELAY START button

!
EN
13
This button allows you to choose between
two different options, depending on the
selected programme.
- RAPID
The button becomes active when
you select the RAPID (14/30/44 Min.)
programme on the knob and allows you to
select one of three durations indicated.
- STAIN / SOIL LEVEL button
!Once the programme has been selected
the wash time set for that programme will
be automatically shown.
!This option allows you to choose between
3 levels of wash intensity modifying the
length of the programme, depending on
how much the fabrics are soiled (can only
be used on some programmes as shown
in the table of programmes).
!This option allows you to make a prewash
and it is particularly useful for heavily
soiled loads (can be used only on
some programmes as shown in the
table of programmes).
!We recommend you use only 20% of the
recommended quantities shown on the
detergent pack.
With this option it is possible to hygienize
the clothes, the washing programme
reach a temperature of 60°C.
!This button allows you to add rinses at
the end of the washing cycle. The
maximum number of extra rinses is
related to the programme selected.
!This function has been studied for the
people with delicate and sensitive skin,
for which also a least residue of detergent
can cause irritations or allergies.
!It advises to also use this function for the
children items and in case of washings of
very dirty items, for which it is due to use
a lot of detergent, or in the washing of
toweling items whose fibres mostly have
the tendency to hold the detergent.
This button allows a specific treatment to
follow certain wash cycles (please refer to
the program table). The steam function
works by relaxing creases in wet garments
and as a result reduces the time needed to
iron these items. The fibres are regenerated
and refreshed by removing bad smells.
Every program provides a dedicated steam
treatment in order to ensure the maximum
cleaning efficiency according to the items
fabric type and colour.
This function allows you to save the settings
of your two favourite personalised
programmes, including the temperature,
spin speed and soil level, so you can recall
them quickly.
How to memorize a programme for the
first time:
1)
Select the programme and the
options you want.
2)
Press the FAVOURITES button,
choosing either M1 or M2. You should
choose M1 if this is the first
programme you have saved.
3)
Keep your finger on the
FAVOURITES button for about 3
seconds to save the combination in
the chosen position.
RAPID / STAIN / SOIL LEVEL button
PREWASH button
HYGIENE PLUS button
EXTRA RINSE button
STEAM button
FAVOURITES button

!
14
Memorize a new programme when M1 &
M2 already have programmes saved:
1)
Set the programme and the options
you want.
2)
Press the FAVOURITES button for
about 3 seconds to save the
combination in the position M1. The
pre-existing saved programme in M1
will move in the position M2.
Start a program that is already
memorized:
!Press briefly the FAVOURITES button
(once for M1, twice for M2) and press the
START/PAUSE button.
!Once you recall a memorized program,
you can still change its options and
settings, pressing the corresponding
keys. In this case, the added options
won’t be memorized.
!This option reduces the intermediate spin
speed to 400 rpm, where applicable,
increase the water level during rinsing
and keep the laundry immersed in water
after the final rinse, in order to spread the
fiber perfectly.
!
During the phase in which the water is
held in the tub, the relevant indicator light
will blink to show that the machine is at a
standstill.
!
Deselect the option to end the cycle with
a spin dry (which may be reduced or
cancelled using the appropriate button)
and emptying phase.
!Thanks to electronic control, the water in
the intermediate phases is emptied
silently, making this option very useful for
washing at night.
!Pressing simultaneously the buttons
NIGHT & DAY and DELAY START for
about 3 seconds, allows you to lock the
keys. This will prevent accidental or
unwanted changes if a button on the
display is pressed accidently during a
cycle.
!The key lock can be simply cancelled by
pressing the two buttons simultaneously
again or by turning the programme knob
to OFF.
The display’s indicator system allows you to
be constantly informed about the status of
the machine.
2
13 14
1 615 10 12 5
7 7 7 7 7
8 9 411
3
1) DOOR LOCKED INDICATOR LIGHT
!The indicator light is illuminated when the
door is fully closed.
!
When START/PAUSE is pressed on
the machine with the door closed, the
indicator will flash momentarily and then
illuminate.
If you accidently select a memorized
program, simply turn the program
knob to select another one.
NIGHT & DAY button
KEY LOCK
Digital Display
Close the door BEFORE selecting the
START/PAUSE button.

!
EN
15
!Wait until the DOOR LOCKED light has
gone out before opening the door.
2) SPIN SPEED
This displays the spin speed of the selected
programme that it can be changed or
omitted by the relevant button.
spin speed cancelled.
3) WASH TEMPERATURE
This show the washing temperature of the
selected programme that can be changed
(where allowed) by the relevant button.
cold wash.
4) CYCLE DURATION
!When a programme is selected the
display automatically shows the cycle
duration, which can vary, depending on
the options selected.
!Once the programme has started you will
be kept informed constantly of the time
remaining to the end of the wash.
!The appliance calculates the time to the
end of the selected programme based
upon a standard loading, during the cycle,
the appliance corrects the time to that
applicable to the size and composition of
the load.
5) STAIN / SOIL LEVEL INDICATOR LIGHTS
!Once the programme has been selected,
the indicator light will automatically show
the stain level set for that programme.
!Selecting a different stain / soil level the
relevant indicator will light up.
6) EXTRA RINSES INDICATOR LIGHTS
The indicator lights show the extra rinses
selected by the relevant button.
7) OPTIONS INDICATOR LIGHTS
The indicator lights show the options that
can be selected by the relevant buttons.
8) Wi-Fi (some models only)
!In the models with the Wi-Fi option, the
icon indicates that the Wi-Fi system is
working.
!For all the information about the
functionality and the instructions for an
easy configuration of the Wi-Fi, please
refer to the "Download" section on
http://wizardservice.candy-hoover.com.
9) DELAY START INDICATOR LIGHT
This flashes when delay start has been set.
10) Kg MODE (function active only on
certain programmes)
!For the programmes where the
"Kg MODE" function is active, the
appliance in the first minutes it calculates
the real laundry loaded, updating the
levels on the display in real time.
Every levels shown on the display is the
20% of the maximum loading capacity.
When a programme is selected the
maximum capacity suggested is shown
on the display.
!The "Kg MODE" displays information on
the wash load. During the first couple of
minutes, it will:
- adjusts the amount of water required;
- determines the length of the wash cycle;
If the door is not properly closed,
the light will continue to flash for
about 7 seconds, after which the
start command will be automatically
canceled. In this case, close the
door in the proper way and press
the START/PAUSE button.

!
16
- controls rinsing according to the type of
fabric selected to be washed;
- adjusts the rhythm of drum rotation for
the type of fabric being washed;
- recognizes the presence of lather,
increasing, if necessary, the amount of
water during rinsing;
- adjusts the spin speed according to the
load, thus avoiding any imbalance.
11) FAVOURITES
The indicator light shows that the memory
function is working.
12) KEY LOCK INDICATOR LIGHT
The indicator light shows that the keys are
locked.
13) TAP CLOSED INDICATOR LIGHT
Indicates that the machine is unable to load
the water: it is suggested to turn off the
machine, check that the tap is open and the
water pressure is not particularly low.
14) FILTER BLOCKED INDICATOR LIGHT
Indicates that the machine is not able to
drain the water: it is suggested to turn off
the machine, check that the filter is not
clogged or that the drain hose is not kinked
or crushed.
15) STANDARD COTTON PROGRAMMES
LIGHTS (see table of programmes)
The lights will light up when you select the
most efficient program in terms of water and
energy consumption, to wash cotton
garments with a normal grade of soil.

!
EN
17
This appliance is equipped with ONE Fi
EXTRA technology that allows you to control
it remotely via App, thanks to Wi-Fi function.
MACHINE ENROLLMENT (ON APP)
!Download the Hoover Wizard App on
your device.
!
Open the App, create the user profile and
enroll the appliance following the
instructions on the device display or the
"Quick Guide" attached on the machine.
NOTES:
ENABLE REMOTE CONTROL (VIA APP)
After the machine enrollment, every time
you want to manage it remotely through the
App, firstly you have to load the laundry, the
detergent, close the door and select the
ONE FI EXTRA position on the machine.
From that moment on you can manage it
through the App commands.
ONE Fi EXTRA
The Hoover Wizard App is available
for devices running both Android and
iOS, both for tablets and for
smartphones.
Get all the details of the ONE Fi EXTRA
functions by browsing the App in
DEMO mode.
Using an Android smartphone
equipped with NFC technology (Near
Field Communication), the enrollment
process is simplified (Easy Enrollment);
in this case, follow the instructions on
the phone display, PLACE AND KEEP
IT NEAR the ONE Fi EXTRA logo
on the machine dashboard, when
requested to do so by the App.
Place your smartphone so that the
NFC antenna on its back matches
the position of the ONE Fi EXTRA logo
on the appliance (as illustred below).
If you do not know the position of
your NFC antenna, slightly move the
smartphone in a circular motion over
the ONE Fi EXTRA logo until the App
confirms the connection. In order for
the data transfer to be successful, it is
essential TO KEEP THE SMARTPHONE
ON THE DASHBOARD DURING THE
FEW SECONDS OF THE PROCEDURE;
a message on the device will inform
about the correct outcome of the
operation and advise you when it is
possible to move the smartphone
away.
Thick cases or metallic stickers on
your smartphone could affect or
prevent the transmission of data
between machine and telephone. If
necessary, remove them.
The replacement of some components
of the smartphone (e.g. back cover,
battery, etc...) with non-original ones,
could result in the NFC antenna removal.

!
18
PROGRAMME
(MAX.)
1)
2
1
(see control panel)
(MAX.)
2
1
All In One 20°C
4)
6,5
20°
All Hygiene
4)
6,5
60°
All In One 59 Min.
10
40°
14'
1,5
30°
Rapid
3)
14-30-44 Min.
30'
2,5
30°
44'
3,5
40°
Dark Colours
4)
5
40°
( )
Wool
2
40°
Handwash & Silk
2
30°
Rinse
-
-
Drain & Spin
-
-
Shirts
2)
4)
5
30°
( )
Delicates
4)
2,5
40°
Mixed
2)
4)
5
60°
( )
*
2)
4)
10
60°
( )
Whites
2)
4)
10
90°
( )
Position that you have to select when you want to enable remote control through
the App (via Wi-Fi). If the machine is not enrolled on the app yet, pressing the
START/PAUSE button on the appliance will perform the "Auto-Hygiene" cycle,
made to clean the drum.
Table of programmes

!
EN
19
Please read these notes:
( )
Only with PREWASH option
selected (programmes with
PREWASH option available).
(Only for models with liquid
detergent compartment)
When only a limited number of
articles have stains which require
treatment with liquid bleaching
agents, preliminary removal of
stain can be carried out in the
washing machine.
Pour the bleach into the liquid
bleach container, inserted into the
compartment marked "2" in the
detergent drawer, and set the
special programme RINSE.
When this phase has terminated,
turn the programme selector to
the OFF position, add the rest of
the fabrics and proceed with a
normal wash on the most suitable
programme.
1)
When a programme is selected,
the display shows the recommended
wash temperature, it can be
reduced (where allowed) by the
relevant button.
2)
For the programmes shown you
can adjust the duration and
intensity of the wash using the
STAIN / SOIL LEVEL button.
3)
If the RAPID program is selected
with the knob, the rapid programs
14', 30' and 44' will become
available to select by using the
RAPID button.
4)
Steam Function Available.
* Programme tested in accordance
with AS/NZS 2040.2 with a temperature
of 40°C.
Programme also recommended for
low-temperature washes (lower than the
max. shown).
The “Cottons" programme at 40 deg.C,
1400 RPM spin with "Max soil Level"
setting is the program recommended for
a normally soiled load at the rated
capacity 10 kg.”

!
20
To clean different types of fabrics and
various levels of soil, the washing machine
has specific programs to meet every need
of washing (see table of programmes).
ALL IN ONE technology
This washing machine is equipped with an
innovative system with an high pressure jet
that sprays a mixture of water and
detergent directly into the load. The special
motor movement used in this machine
manages the drum movement during the
start up of each programme, in conjunction
with the high pressure jet spraying the
detergent mixture into the load, the cycle
includes a set of spin actions that helps the
detergent solution to penetrate into the
fibers, helping dirt removal and ensuring
the best available wash performance. The
ALL IN ONE system is also used during the
water load phases where the high pressure
jet aids the complete removal of detergent
residues trapped in the clothes
All In One 20°C
Thanks to ALL IN ONE technology, this
innovative programme, allows you to wash
fabrics such as cottons, synthetics and
mixed fabrics at 20°C with a performance
which is comparable to a 40°C wash. The
consumption of this program is about 50%
of a conventional 40°C. Cottons wash.
IMPORTANT WASH PERFORMANCE
ADVICE:
!New, coloured garments should be washed
separately for at least 5 or 6 washes.
!Certain large dark items such as jeans
and towels should always be washed
separately.
!Never mix NON COLOURFAST fabrics.
All Hygiene
Thanks to the ALL IN ONE technology, this
program ensures deep cleaning by
optimizing the cycle in terms of temperature
and rinses, eliminating allergens and
detergent residues. Ideal for sensitive skin.
Designed for cotton garments, it provides a
60°C temperature and is recommended for
a reduced load.
All In One 59 Min.
This programme allows you to wash mixed
fabrics such as cottons, synthetics and
mixed fabrics in only 59 minutes, using the
full load of the washing machine, at 40°C
(or less) temperature. This programme is
particularly suited to slightly soiled fabrics.
Rapid (14-30-44 Min.)
Washing cycle suggested for low loads and
slightly soiled. With this program it is
recommended to reduce the quantity of
detergent normally used, in order to avoid
unnecessary waste. Selecting the RAPID
program and acting on the button you can
choose one of three programs available.
Dark Colours
Program designed to mix all dark garments and to
avoid the loss of colour and the formation of creases.
We recommend the use of liquid detergent.
Wool
This program performs a wash cycle
dedicated to the wool fabrics that can be
washed in a washing machine, or the
articles to be washed by hand.
Handwash & Silk
This programme allows a delicate washing
cycle for garments specified as "Hand
Wash only" and laundry items made from
Silk or specified as "Wash as Silk" on the
fabric label.
Rinse
This program performs 3 rinses with an
intermediate spin (which can be reduced or
excluded by using the appropriate button) . It
is used for rinsing any type of fabric, for
example after a wash carried out by hand.
Drain & Spin
The program completes the drain and a
maximum spin. It is possible to delete or
reduce the spin with the SPIN SPEED button.
Shirts
The washing cycle is optimized to reduce the
creation of creases, keeping an excellent washing
performance. It is also possible to further reduce
the spin speed, to ensure an easier ironing.
Programmes selection