Hoshizaki SRM-45A User manual

COMMERCIAL SELF-CONTAINED RHOMBIC
ICE MAKER
INSTRUCTION MANUAL
SRM-60A/80A
●This booklet is an integral and essential part of the product and should be kept and
Preserved by the user.
●Please read carefully the guidelines and warnings contained herein as they are
intended to provide the installer / user with the essential information for the proper
installation and continued safe use and maintenance of the product.
●Please preserve this booklet for any further consultation that may be necessary.
Manufacturer: HOSHIZAKI (SUZHOU) CO., LTD
No. 15 Qingqiu Street, Suzhou Industrial Park, Suzhou 215126.China
SRM-45A
SRM-60A
SRM-80A
SRM-105A
SRM-125A
L1M078101(011518)

CONTENT
IMPORTANT SAFETY INFORMATION.....................................................................................1
Ⅰ . INSTALLATION INSTRUCTIONS..........................................................................................2
1. CONSTRUCTION..............................................................................................................2
2. ACCESSORIES.................................................................................................................3
3. UNPACKING......................................................................................................................4
4. LOCATION..........................................................................................................................6
5. INSTALLATION..................................................................................................................6
6. ELECTRICAL CONNECTIONS.......................................................................................6
7. WATER SUPPLY AND DRAIN CONNECTIONS.........................................................7
Ⅱ. OPERATING INSTRUCTIONS................................................................................................8
1. START UP..........................................................................................................................8
2. PREPARING THE ICEMAKER FOR LONG STORAGE.............................................8
Ⅲ. MAINTENANCE........................................................................................................................9
1. CLEANING..........................................................................................................................9
[a]Machine and Bin Exterior..........................................................................................9
[b]Scoop cleaning/Sanitisation (Daily).........................................................................9
[c]Storage Bin Interior Cleaning/Sanitisation (weekly)..............................................9
[d] Air Filter and Condenser........................................................................................11
2. PRECAUTIONS...............................................................................................................12
3. FAULT AND TREATMENT.............................................................................................13
4. BEFORE CALLING FOR SERVICE.............................................................................13
5. DISPOSAL........................................................................................................................13
6. WARRANTY.....................................................................................................................14
SPECIFICATION..........................................................................................................................14

1
IMPORTANT SAFETY INFORMATION
Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury or damage
to the unit.










W
A
RNING Indicates a hazardous situation which, If not avoided, could result in death or serious injury.
C
A
UTION Indicates a hazardous situation which, If not avoided, could result in minor or moderate injury.
NOTICE Indicates a hazardous situation which, If not avoided, could result in damage to the unit.
HYGIENE Indicates important precautions for hygiene and food safety.
INPORTANT Indicates important information about the use and care of the unit.
WARNING
The ice maker is a commercial icemaker, and should be destined only to be used for the purpose for which it has been expressly
designed.
Any other use should be considered improper and therefore dangerous. The manufacturer will not be held liable or responsible
for any damage caused by improper, incorrect and unreasonable use.
The installation, and relocation if necessary, must be carried out by qualified personnel, in accordance with current regulations,
according to the manufacturer’s instructions.
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
The use of any electrical appliance involves the observance of some fundamental rules. In particular:
＊Instance of any high humidity and moisture increase the risk of electrical short circuits and potential electric shocks. If in doubt,
disconnect the icemaker.
＊Do not damage the power cord or pull it in order to disconnect the icemaker from the electrical supply network.
＊Do not touch electrical parts or operate the switches with damp hands.
＊This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
＊Young children should be supervised to ensure that they do not play with the appliance.
＊Do not attempt to modify the ice maker. Only qualified personnel may disassemble or repair the appliance.

2
Ⅰ . INSTALLATION INSTRUCTIONS
1. CONSTRUCTION
[SRM-45A]
[SRM-60/80A]
Top Panel
Storage Bin
Louver
id
Power Switch
Door handle
Name Plate
A
ir Filter
Door handle
Name Plate
Air Filter
Top Panel
Storage Bin
Louver
id
Power Switch

3
[SRM-105/125A]
2. ACCESSORIES
SRM-45
A
SRM-60
A
SRM-80
A
SRM-105
A
SRM-125
A
Instruction Manual 1 1 1 1 1
Scoop 1 1 1 1 1
Leg 0 4 4 4 4
Instruction Manual Scoop Leg
Door handle
Name Plate
A
ir Filter
Top Panel
Storage Bin
Louver
id
Power Switch
Front Panel - Middle

4
3. UNPACKING
W
A
RNING
Children should not be allowed in reach of the Packaging elements (plastic bags and expanded polystyrene, etc.) as they are
potential sources of danger.
C
A
UTION
Do not lift or manoeuvre the carton by using the shipping bands.
When moving the unit, hold the unit bottom.
A
lways wear protective gloves when carrying the unit.
When handing the carton or the unpacking unit, work in pair to prevent injury.
NOTICE
Remove shipping carton, tape(s) and other packing. If the packing material is left in the ice maker, it will not work properly.
1) After removing packing, make sure that the icemaker is in good condition. If in doubt, please do not use the icemaker, but
apply to professionally qualified personnel.
2) Remove the shipping tape holding the door and front panel.
3) Remove the protective film from the exterior. If the icemaker is exposed to the sun or to heat, remove the film after the
icemaker cools.
4) Remove the shipping tape holding accessories by opening the door
5) Remove the package of accessories. Check the contents according to “2.ACCESSORIES”
[SRM-45A]
Bin Door

5
[SRM-60/80A]
[SRM-105/125A]
Bin Door
Bin Door

6
4. LOCATION
W
A
RNING
This ice maker is not intended for outdoor use.
This ice maker should not be located next to ovens, grills or other high heat producing equipment.
This appliance is not suitable for installation in an area where a water jet could be used.
C
A
UTION
The location should provide a firm and level foundation for the icemaker.
NOTICE
Do not place anything on top of the icemaker or in front of louver.
IMPORTANT
Normal operating ambient temperature should be within 5℃ to 38℃. Normal operating water temperature should be within
5℃ to 32℃. Operation of the icemaker, for extended periods, outside these normal temperature ranges may affect production
capacity and life.
Allow the clearance specified below for proper air circulation and ease of maintenance and/or service should they be required.
【NOTE: SRM-45
A
:L=1cm; SRM-60/80/105/125
A
: L=15cm.】
In some high humidity environments, condensation may from inside the machine and drip onto the floor. Do not install where
the floor can be affected by water.
5. INSTALLATION
C
A
UTION
Incorrect installation can cause harm to people, animals or other items, for which the manufacturer cannot be held
responsible.
＊Place the icemaker in selected permanent site.
＊When attaching the adjustable lets / nuts (accessory),
level the unit in both the left-to-right and
front-to-rear directions
[SRM-45A] [SRM-60/80/105/125A]
6. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national and local electrical code requirements.
To prevent possible severe electrical shock to individuals or extensive damage to the unit, install a proper earth wire to the
icemaker.
Disconnect the main power supply before any maintenance, requires or cleaning is undertaken.
＊This series of icemaker require a separate power supply (220VAC/10A). The electrical supply must be protected by a suitable
circuit breaker.
＊The main control box fuse is rated at 5A and should be replaced by a qualified service engineer.

Ice maker
15cm15cm
0cm
Rea
r
Ri
g
ht
Left
Front
Top View
Ice
maker
L cm
0cm
Top
Rea
r
Adjustable
Leg
Side View
Adjustable
Nut

7
＊Usually an electrical permit and services of a licensed electrician are required.
＊If the power cord is damaged, it must be replaced by a replacement cord available from Manufacturer Parts/Service Centres.
7. WATER SUPPLY AND DRAIN CONNECTIONS
W
A
RNING
Connect to potable water supply only.
＊The connection to the main water supply must be made in accordance with the countries’ current requirements of the Water
Supply or Water Fittings Regulations.
＊Icemaking water must be potable water. Where scaling can be caused by water quality:
-Installation of an external filter or softener is recommended. Contact your local water treatment professional or the
manufacturer’s agency.
-Multistage filtering or deionized filtering may result in the product's failure to work properly. (The reference value of water
conductivity ≥20μs/cm)
＊Water supply pressure should be within 0.07MPa（0.7bar）to 0.55MPa（5.5bar）. If the pressure exceeds 0.55MPa (5.5bar),
use a proper pressure reducing valve. Do NOT throttle back the supply tap.
＊A plumbing permit and services of a licensed plumber may be required in some areas.
＊The icemaker drain is gravity flow, so ensure drain pipe has an adequate pitch or fall.
＊Drain line should not be piped directly to the sewer system. A vertical air gap of minimum of 5cm should be between the end of
the drain pipes from the icemaker and the floor drain.
＊To prevent a backflow into the storage bin, the outlet hose must be laid as shown.
＊Be sure to use the new hose-sets supplied with the appliance. Do not reuse any old hose-sets.
1) Attach the free end of inlet hose to the stop valve, noting washer is correctly positioned. Hand
tighten sufficiently to provide leak free joint. It is a wise precaution to have the stop valve within
easy reach.
2) The outlet hose can be cut to appropriate length according to the position of the main drain nozzle.
To prevent condensation, it can be coated some insulation pipe out of drain pipe.
Note: Jointing compounds should be approved and suitable for potable water use.
[SRM-45A] [SRM-60/80/105/125A]
BAD BAD
Inlet Hose
U
Inlet Hose Outlet Hose
GOO
D
Downgrade Upgrade
Washer
Stop Valve
Outlet HoseInlet Hose

8
Ⅱ. OPERATING INSTRUCTIONS.
CAUTION
Do not put your hand into the back of the storage bin or the right side pump.
The ice on the evaporator may drop off, a hard block of ice may suddenly
break down, or pump motor may suddenly start-up, resulting in injury.
NOTICE
A
ll parts are factory-adjusted. Improper adjustments may result in failure.
If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor.
HYGINEN
This icemaker is designed to produce edible ice. To keep the icemaker hygienic:
＊Wash your hands before removing ice. Use the plastic scoop provided (accessory).
＊The storage bin is for ice use only. Do not store anything else in the bin, nor use other electrical appliances in the bin.
＊Clean the storage bin before use (see "III.1. CLEANING").
＊Keep the scoop clean. Clean it by using neutral cleaner and rinse thoroughly.
＊Close the door after removing ice to prevent entrance of dirt, dust or insects into the storage bin.
1. START UP
The installer will normally commission the icemaker to start the automatic icemaking process. To ensure continuous operation.
Make sure that:
＊The water supply tap is on, and
＊The icemaker is connected to the power supply.
2. PREPARING THE ICEMAKER FOR LONG STORAGE
NOTICE
This icemaker will not work at subfreezing temperatures. To prevent damage to the water supply line, drain the icemaker
when air temperature is below zero.
HYGIENE
When shutting down the icemaker for two or more days, drain the icemaker to prevent contamination in the water circuit.
1) Unplug the icemaker or disconnect the power supply.
2) Close the water supply tap, and remove the inlet hose.
3) Remove all ice from the storage bin, and clean the bin.
4) Ask for draining of the icemaker by professional qualified personnel.
Water Tank
Storage Bin

9
Ⅲ. MAINTENANCE
1. CLEANING
WARNING
Before carrying out any cleaning or maintenance operations, unplug the icemaker from the electrical supply network.
This appliance must not be cleaned by use of a water jet.
C
A
UTION
When using a neutral cleaner or sodium hypochlorite, thoroughly read and understand the instructions provided to prevent
potential health problems.
NOTICE
Ask a trained service person to clean and sanitize the icemaker water system at least twice a year and to check and clean the
condenser at least once a year.
To prevent possible damage, do not clean the plastic parts with water above 40℃ or in a dishwasher.
[a]Machine and Bin Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use a damp cloth containing a neutral cleaner to
wipe off grease or dirt.
Notice
Do not use hard brushes, wire brushes, nor detergents, gasoline, banana oil, acetone and other organic solvents. Do not use
boiling water or acid and alkali cleaners to clean the machine.
Do not rinse with water spray when cleaning, so as not to affect the insulation of electrical appliances.
[b]Scoop cleaning/Sanitisation (Daily)
Step 1: Either mix 1 L of water with 4mL of 5.25% sodium hypochlorite solution in a suitable container, or the recommended
manufacturer sanitizer as directed.
Step 2: Soak the scoop in the solution for more than 3 minutes. Rinse thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
[c]Storage Bin Interior Cleaning/Sanitisation (weekly)
Note: Because of the different water quality in various regions, some areas may need to be cleaned and sterilized
more frequently.
(1) Cleaning
Step 1: After the ice removal cycle and all ice totally dropped, disconnect the power supply and cut off the water
supply. Open the door, remove the top panel and rear panel, and remove all ice.
NOTICE
To prevent damage the evaporator, the ice on the evaporator cannot be stripped by tools.
To protect the plastic parts, no alcohol-containing liquid can be used to clean or sterilize the icemaker.
Step 2: Open the drain outlet, empty the water in the water tank and water circuit, and then remove the inlet hose, the pump
connection tube and the overflow hose in the ice storage bin.
Step 3: According to the steps of diagram remove the ice thickness sensor, water spray tube and overflow hose, pump motor, bin
switch, water tank and so on.
Step 4: Use soft brush soaked in a neutral detergent, sponge or clean cloth to carefully clean the surface of the dismantled parts
(the water pipes/tubes/hoses include the inner surface). Then clean them with clean water.
Note: During cleaning water spray tube, the inner tube must be removed. Water spray tube must be cleaned with a soft brush
dipped in a neutral detergent, cleaning cloth or sponge, and then rinsed with water.
Because evaporator can't be removed, use the soft brush, sponge or clean cloth soaked by the neutral detergent to clean it
carefully.
For the pump motor and the ice thickness sensor and other parts, only the water circuit parts can be cleaned. All the
electrical parts cannot be immersed in the cleaning agent. Please avoid it carefully.

10
Cleaning agents must be the food class or a cleanser recommended by the manufacturer.
Some solutions may damage the inner surface of the storage bin or corrode the metal parts. Cleaning liquid must be
cleaned at any time unless otherwise specified by the manufacturer.
[SRM-45/60/80A]
[SRM-105/125A]
Disassembly steps of water spray tube
1. Use tool to unload two
screws of the pump motor,
lift up the pump motor and
bracket, and take down the
pump motor.
2. The motor part of the
pump motor should
not be soaked in the
cleaning agent or
disinfectant.
1. Take ice thickness
sensor off
2. Use the tool to
unload two
screws.
3. Lift water spray
tube up
1. Disassemble two screws
2. Pull the rubber plug out
3. Pull the rubber plug out
Pump motor disassembly steps
Disassembly steps of ice thickness sensor and water spray tube
1. Take ice thickness sensor off
3. Take drain-pipe up forward
2. Use the tool to unload
two screws

11
【NOTE: If no special instructions, all contents are suitable to SRM-45/60/80/105/125A]
(2) Disinfection
Step 5: Pure 3 liters of water into one suitable container, mix it with 11 mL concentration of 5.25% sodium hypochlorite solution
or a disinfectant recommended by the manufacturer. Immerse the removed parts (ice thickness sensor, water spray tube
and overflow hose, pump motor, bin switch, water tank, etc.) in disinfection liquid about 3 minutes.
Note: When the pump motor is sterilized, the electrical components cannot be immersed in the disinfectant. Do not sterilize bin
switch, ice thickness sensor.
Step 6: Use a clean sponge or cloth soaked in a soultion to wipe inner of bin and door.
Step 7: After the disinfection, rinse thoroughly with clean water to make sure that there is no residual disinfectant.
Step 8: Install the dismantled parts according to the reverse order of disassembly, finally close door and restore the water supply
and power supply.
Note: When only water tank to clean, just dismantle water tank and overflow hose to be cleaned.
[d] Air Filter and Condenser
Plastic mesh air filters removed dirt or dust from the air, and keep the condenser from getting clogged. If the filters get clogged,
the icemaker’s performance will be reduced. Remove and clean the air filters at least twice per month.
Step 1: Slide the air filter off the louver.
Step 2: Clean the air filter by using a vacuum cleaner. When severely clogged , use warm water and a neutral cleaner to wash
the air filter.
Step 3: Rinse and dry air filter thoroughly.
Step 4: The condenser of the air-cooled icemaker normally is cleaned once or twice per year. Use a soft brush or a vacuum
cleaner with brush to scrub the fin of the condenser in the direction of the fins, to prevent damage the condenser’s fin and
affect the icemaking.
2. Screw 3 fixed Hex screws
1. Catch the left side of ice guide.
2. Press the right side of ice guide bracket.
3. Pull ice guide body forward until it is pulled out from
the hole on the left side.
1
2
3
Drain outlet of water tank
Disassembly steps of water tank
Disassembly steps of ice guide
1. Pull the overflow hose out

12
NOTICE
A
fter cleaning, be sure to install the air filter back to the original place.
[ SRM-45/60/80/105/125A ]
2. PRECAUTIONS
1. The icemaker will have a larger “buzzing” sound when it begins to run because the operation is not stable at first time of
powering-on or start. The sound will be reduced after stable.
2. It is normal that the temperature of compressor case is very high after the icemaker works for a long time.
3. The sound of compressor and the "clicking" sound of the compressor and the solenoid valve when icemaker turns on or off are
normal phenomenon.
4. It is normal that the icemaking cycle becomes longer and the icemaking efficiency decreases when the air temperature is high.
5. The power consumption value on the nameplate is calibrated according to the national standard in the laboratory environment.
When the ambient temperature and water temperature are higher (such as summer air temperature and water temperature are
higher), it is normal that the real consumption is higher than the value on the nameplate.
6. Contact the servicers to adjust the ice thickness sensor.
Air Filter
Louver
Out
In

13
3. FAULT AND TREATMENT
Please operate the machine according to the instructions. If there are any exceptions, please check the follow table firstly. If it
cannot be solved, please contact the authorized distributor or maintenance agency of our company in time. So as not to cause a
loss to you.
Fault Probable Cause Processing method
No icemaking
The power switch is not allocated to the "icemaking"
position. Switch the power switch.
The connecto
r
of the power cord is loose. Fasten the power cord connector.
The voltage is too high or too low. Check and use the proposed voltage.
The plu
g
is not plu
gg
ed. Plu
g
in the plu
g
.
The icemaker starts when stora
g
e bin is full Take out the ice.
When the water supply is closed Check and connect to normal water pressure. Open
the water valve to check the water intake.
The filter of inlet hose or the inlet month is blocked. Clean the filter net of the inlet hose.
The sewera
g
e stopper in the tank did not plu
g
.Plu
g
the rubber plu
g
of drain outlet.
Evaporator freezing
The evaporator is dirt
y
. Clean the evaporator.
The ice is too thick.
A
djust the length of the screw of the ice thickness
sensor.
The icemaker was not leveled. Put the icemake
r
level.
The water suppl
y
s
y
stem is dirt
y
. Clean the water suppl
y
circuit.
The filter of water supply valve or the entrance of the inlet
hose is blocked.
Clean up the entrance of the water supply valve and
inlet hose
The ambient temperature or water temperature is too low. Raise the temperature.
Ice maker cannot remove ice.
Ice thickness sensor is dirty Clean the ice thickness senso
r
Ice thickness sensor wire did not access control board. Connect the wire.
Ice thickness sensor is to be ad
j
usted.
A
d
j
ust the ice thickness sensor.
Bad quality of the ice (not strong
or not clean).
Bad water quality Replace the purification and water treatment device.
The evaporator is dirt
y
. Clean the evaporator.
The ice is sunken or incomplete,
or the ice on the upper layer of
the evaporator is incomplete.
The ice thickness has not been ad
j
usted well.
A
d
j
ust the ice thickness sensor.
The water level in the tank is too high or too low. Check the water level sensor.
The water pressure does not meet the requirements. The water pressure range is between 0.07 ～
0.55MPa.
There is oil on the evaporator. Scrubbin
g
evaporator with a non - oil
y
material cloth.
The ice maker has not been leveled. Put the ice maker flat.
Low ice production
The air filter o
r
the condenser is blocked. Clean air filters o
r
condensers.
The ambient temperature or water temperature is too high.
A
djust the ambient temperature and water
temperature.
The water pressure is too high or too low. The water pressure range is between 0.07 ～
0.55MPa.
The
g
ap of ice thickness is too lar
g
e or too small.
A
d
j
ust the ice thickness sensor.
Ice shape anomaly
The ice guide and the water tank are misplaced, and the
water flow in the icemaker is serious.
Check whether the ice guide is properly installed in the
water tank, and the water tank is firmly fixed in the
storage bin of icemaker.
The water spra
y
tube is dirt
y
. Clean the water spra
y
tube.
The evaporator is dirt
y
. Clean the evaporator.
Water is too hard or contains impurities. Install water cleane
r
.
Excess noise level. Place unstabl
y
. Put the ice maker flat.
The icemaker contacts with other ob
j
ects.
A
void the icemaker contacts with other ob
j
ects.
The melting speed of the ice in
the stora
g
e bin is too fast
The drain system of icemake
r
is blocked. Clean up the drain system.
External contains condensate The door is not closed. Close door completely.
4. BEFORE CALLING FOR SERVICE
WARNING
Do not damage the refrigerant circuit
If the icemaker dose not work properly or dose not work at all, before calling for service, check that:
＊ The power is supplied to the unit.
＊ The water is turned on.
＊ The air filter is clean.
For further assistance or advice, contact the local manufacturer's Maintenance Agency.
5. DISPOSAL
Comply with local regulations regarding disposal of this appliance and its refrigerant gas. Before you scrap the appliance, take off
the door to prevent children trapped.

14
IMPORTANT
The insulation foaming agent used for the unit body contains a flammable gas cyclopentane. With this in mind, dispose o
f
the product properly.
6. WARRANTY
The manufacturer warrants to the original owner / user that all products of the manufacturer's brand shall be free of defects in
material and / or workmanship for the duration of the "warranty period" . The warranty shall be effective for one year from the date
of installation.
The manufacturer liability under the terms of this warranty are limited and shall exclude routine servicing, cleaning, essential
maintenance and/or repairs occasioned by misuse and installations not in accordance with manufacturer guidelines.
Warranty repair should be completed by an approved manufacturer dealer or service agency using genuine manufacturer
components.
To obtain full details of your warranty and the approved service agency, please contact your dealer / supplier or the nearest
manufacturer's service office.
Repair Hotline: [phone]
E-mail: [email protected]
SPECIFICATION
Model SRM-45
A
SRM-60
A
SRM-80
A
SRM-105
A
SRM-125
A
Type Air-cooled,
rhombic ice cube
Air-cooled,
rhombic ice cube
Air-cooled,
rhombic ice cube
Air-cooled,
rhombic ice cube
Air-cooled,
rhombic ice cube
Power
Supply
1 phrase
220～240V 50Hz
1 phrase
220～240V 50Hz
1 phrase
220～240V 50Hz
1 phrase
220～240V 50Hz
1 phrase
220～240V 50Hz
Electrical
Consumption
305W 370W 450W 480W 590W
Ice Production
Per 24h
46kg (ambient 10℃，
water 10℃)
65kg (ambient 10℃，
water 10℃)
80kg (ambient 10℃，
water 10℃)
106kg (ambient 10℃
water 10℃)
125kg (ambient 10℃
water 10℃)
Dimensions 500mm (W)×580mm
(D)×750mm (H)
660mm (W)×670mm
(D)×1050mm (H)
660mm (W)×670mm
(D)×1050mm (H)
660mm (W)×670mm
(D)×1200mm (H)
660mm (W)×670mm
(D)×1200mm (H)
Refrigerant R134a,160g R134a, 220g R404
A
,230g R404
A
,290g R404
A
,350g
Weight Net weight: 36 kg Net weight: 58 kg Net weight: 56.5 kg Net weight: 61 kg Net weight: 64.5 kg
A
mbient Temp 5～38℃ 5～38℃ 5～38℃ 5～38℃ 5～38℃
Water Supply
Temp
5～32℃ 5～32℃ 5～32℃ 5～32℃ 5～32℃
Water Supply
Pressure
0.07～0.55MPa
（0.7～5.5bar）
0.07～0.55MPa
（0.7～5.5bar）
0.07～0.55MPa
（0.7～5.5bar）
0.07～0.55MPa
（0.7～5.5bar）
0.07～0.55MPa
（0.7～5.5bar）
Voltage Range 198～254V 198～254V 198～254V 198～254V 198～254V
Note: The above specifications are for the representative models

15
Contact: Hoshizaki Singapore Pte Ltd
18 Boon Lay Way #07-142
Tradehub 21, Singapore 609966
TEL: [phone]
FAX: [phone]L1F037208
Hoshizaki (Thailand) Limited
No.9/92 Moo 5,Klong Nueng,
Klong Luang,Pathumthani 12120 Thailand
TEL: [phone]
FAX: [phone]
Hoshizaki Hong Kong Co.,Limited
Unit G, 17/F, World Tech Center, No.95 How Street
Kwun Tong, Kowloon, Hong Kong
TEX: [phone]
FAX: [phone]
Hoshizaki Taiwan, Inc
5F, No.337, Sec.1, Dunhua S.Rd., Da’an Dist,
Taipei City 106,Taiwan(R.O.C)
TEL: [phone]
FAX: [phone]