Hotpoint Ariston ARXXL105EU Operating and installation instructions

Indesit Company UK Ltd
© 2007 Reg. Office: Peterborough PE2 9JB Registered in London: 106725
Service
Information
WASHING
MACHINES
Models Comm.
Covered Code
LED
ARXXL105EU 47553
ARXXL105IT 51215
DIGIT
ARXXF125EU 49055
5407388 Issue 1 Oct. 2007

2 of 28
Service Manual UK
Indesit Company
English
SAFETY NOTES & GENERAL SERVICING ADVICE
1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance.
2. It should ONLY be used by suitably qualified persons having technical competence applicable
product knowledge and suitable tools and test equipment.
3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged)
from the electrical supply.
4. Servicing must be preceded by Earth Continuity and Insulation Resistance checks.
5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on
metal and plastic parts.
6. After servicing the appliance must be rechecked for Electrical Safety. In the case of appliances
which are connected to a water supply (i.e.: Washing Machines, Dishwashers & Food Centres etc.)
checks must be made for leaks from seals gaskets and pipe work and rectification carried out where
necessary.
7. Itcanbedangeroustoattempt 'DIY' repairs /maintenance on complex equipmentandtheCompany
recommends that any problem with the appliance is referred to its own Service Organisation.
8. WhilsttheCompany hasendeavouredtoensure theaccuracyofthedata within thispublicationthey
cannot hold themselves responsible for any inconvenience or loss occasioned by any error within.
SERIAL NUMBER / INDUSTRIAL CODE EXPLANATION
Serial Number Example
3 10 02 0895
Four remaining digits = Build number that day 895th built
Third two digits = Day of manufacture 2nd of month
Second two digits = Month of manufacture October
First digit = Year of manufacture 2003
Industrial Code Example
37 24455 0010
Last four digits = 0000 original production.
Second five digits = COMMERCIAL CODE*
First two digits = Factory of origin
* Vital for correct model information and system identification
Other numbers denote major production changes

3 of 28
Indesit Company
Service Manual UK English
INDEX
Safety & Servicing Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Manufacturing Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Development History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Demo Mode - ARXXF125EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controls Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Option Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wiring Diagrams
LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Digit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wiring Connection Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wiring Diagram Legend. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power Module Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Error Codes & Possible Causes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Dismantling Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 - 26

4 of 28
Service Manual UK
Indesit Company
English
SPECIFICATIONS
Models Covered LED Display models - ARXXL105EU, ARXXL105IT
DIGIT Display - ARXXF125EU
Colour White
Country of Origin Great Britain
Electrical Supply 220 - 240 Volt AC @ 50 Hz Fuse 13 amp
Energy Energy Class: A+ @ 6 kg
Washing Performance Class: A+
Spin Efficiency Class: B
Energy Consumption 1.02 kWh / Cycle @ 60°C Cotton
Water Consumption 55 Litres @ 60°C Cotton
Wash Load 6.0 kg Cottons
Washing & Drying Load 5.0 kg Cottons
Spin Speed ARXXL105EU - 1000 rpm
ARXXL105IT - 1000 rpm
ARXXF125EU - 1200 rpm
Control PCB 220/240 Volt 50/60 Hz Type Merloni EVO 2
Water Supply Cold Valve - Coil Resistance 3.8 KΩ
Max Pressure = 1 Mpa (10bar)
Minimum Pressure = 0.05 Mpa (0.5bar)
Wash Heater 1800 Watts @ 230 volts Resistance 30 Ω approx.
Thermistor NTC Resistance: 20 KΩ@ 20°C
Pump 2 Pole Synchronous
220 / 240 Volt 25 Watt, Resistance = 162 Ω
Door Lock P.T.C. Solenoid with emergency door release
Torque Settings Upper Balance Weight = 24 Nm
Lower Balance Weight = 24 Nm
• Make sure that you allow enough space for the machine. Select a space at least
60 cm wide, 60 cm deep and 85 cm high. Also leave enough space to open the door fully, so that
you can load and unload it easily.
• Where possible, the machine should be positioned on a solid floor to minimise vibration.
• Take care when you move the machine not to rip any floor coverings.
Levelling
The machine will be noisy if the two front feet are not adjusted so that the machine stands firm and
level.
• The machine should be levelled from side to side and from front to back.
Dimensions Height 850 mm Width 595 mm
Depth 580 mm Weight 72 kg Packed approx. 73.5 kg

5 of 28
Indesit Company
Service Manual UK English
CONTROLS
LED MODEL
DIGIT MODEL
ON-OFF / SELECTING A PROGRAMME
The machine is switched on by pressing the ON-OFF button.
All the indicator lights will light up for a few seconds.
Turn the programme selector dial to the to the desired programme.
Load the laundry and detergent.
Select the Option you require, a time will be indicated in the display window.
Press the Start / Cancel button.
A beep will be heard followed by a CLUNK from the door lock Solenoid as it locks the door, at this
stage the door locked indicator symbol will light.
On-Off
Programme Selector Dial Variable Controls Progress Indicator Lights
Door Locked
Symbol
On-Off
Programme Selector Dial Variable Progress Indicator Lights
Door Locked
Symbol
Option Buttons Start/Pause Child Lock
Controls Digital
Display
Option Buttons Start/Pause

6 of 28
Service Manual UK
Indesit Company
English
TO STOP OR CHANGE A PROGRAMME
Press the ON-OFF button for approximately 3 seconds
Select PUMP OUT on the programme dial.
Switch on and re-start
When the machine has finished emptying.
Press the ON-OFF button
Select a new programme and re-start
NOTE: If you cancel a HOT wash or Dry programme, take care when removing the laundry, it may still
be VERY HOT.
PROGRESS INDICATOR LIGHTS
These lights will light up when you choose a programme, to indicate the progress of the selected
programme.
When started, the first light in the cycle will stay lit and as the programme progresses, successive
lights will come on until the programme finishes.
DOOR LOCKED INDICATOR LIGHT
The 'Door Locked' indicator light will come on when you press the START / PAUSE button and will stay
lit throughout the programme. When the programme has finished the indicator light will go out and you
can then open the door, a double CLUNK noise will be heard from the door lock Solenoid at this point.
If the door is not closed properly prior to starting a programme the door lock solenoid will 'CLUNK'
approximately 5 times followed by a flashing DOOR indication in the display window, every 5 seconds
from then onwards there will be an audible beep.
Push the door closed and press START / PAUSE button to commence the cycle.
CHILD LOCK - Model ARXXF125
To set the Child Lock, start the programme required then press and hold the Child Lock button for
2 seconds. At this point a red LED will illuminate on the button - Child Lock function is now active.
To Remove Child Lock - Press and hold the Child Lock button down for 2 seconds.
NOTE: - The Child Lock option will need to be removed before another programme can be selected.

7 of 28
Indesit Company
Service Manual UK English
OPTIONS
Options are selected by pressing the button and confirmed by illumination an orange LED situated in
the button.
If an option is not available with a programme, the LED will flash and a bleeping noise will be heard
when pressing the button.
MINI LOAD
For washing a smaller load.
In addition to reducing actual washing time, this option will reduce water and energy consumption by
up to 50%.
NOTE: - You can reduce the amount of detergent you use with this programme.
EXTRA RINSE
For large wash loads and items for young children or people with sensitive skin.
This option adds a rinse.
EASY IRON
To reduce creasing to a minimum and save you ironing time.
TIME DELAY
With this option you can delay the start time of the programme between 1 and 24 hours.
TIME DELAY
MINI LOAD - MINI CARICO
EXTRA RINSE - EXTRA RISCIACQUO
EASY IRON - STIRA FACILE

8 of 28
Service Manual UK
Indesit Company
English
DEMO MODE - ARXXF125EU
To Activate Demo Mode
Press and hold the following buttons simultaneously: -
ON/OFF BUTTON
EASY IRON
START / PAUSE
To De-select Demo Mode
Press and hold the following buttons simultaneously: -
ON/OFF BUTTON
START / PAUSE
On/Off Easy Iron Start/Pause

9 of 28
Indesit Company
Service Manual UK English
CONTROLS INFORMATION
A single control board located at the back of the machine contains all the circuitry to control the
machine and interfaces with the programme selector, option buttons and LEDs located on the console
panel. The control board has an access port to the rear of the machine.
Programmes are selected by turning the rotary switch to one of the 16 positions. Special options can
be selected by pressing the appropriate buttons and the programme process followed by LEDs.
The machine is switched on using the On/Off button and selected programmes started by pressing the
Start/Cancel button.
Automatic Features
Auto Half Load
Auto half load adjusts the amount of water in the wash load depending on the absorbency of garments
in the wash load.
Fabric Conditioner Dispensing
Dispensing of fabric conditioner is achieved by energising both the Pre-Wash and Main Wash cold
valves.
Out of Balance Protection
The machine has an inbuilt feature to prevent spinning with an unbalanced load. A calculation via the
motor tacho and control board detects the current drawn by the motor during distribution.
Before each spin, the controls senses the load within the drum and if the load is calculated to be out of
balance the machine will not automatically spin to the full speed.
There are two levels of out of balance, level 1 @ 480 grammes and level 2 @ 1030 grammes.
If the out of balance is below level 1 the machine will spin at full speed, if between level 1 and level 2
the machine will spin at the reduced speed of 600 rpm and above level 2 spin at reduced speed of 400
rpm. There are 15 attempts at level 1 with 57 attempts in total, this being the same for both cotton and
synthetic spins.
The wool spin has one level of out of balance @ 1.8 kg. The controls will make three attempts to
achieve a balance, if after three attempts a balance is not achieved; the spin is reduced to a speed of
90 rpm.

10 of 28
Service Manual UK
Indesit Company
English
OPTION AVAILABILITY
SPECIAL PROGRAMME DESCRIPTIONS
FRESH UP (15 MIN)
Load: 1.5 kg
Cycle duration: 15 minutes
Extra fast wash programme with the same performance of a 30º wash
SANITARY
Load: 6.5 kg
Cycle duration: 3.5 Hours
90º programme that can use bleach together with the perfect rinse to remove Bacteria
NIGHT CYCLE - Temperature 40°C - Spin 800 rpm
Load: 4.0 kg
Cycle duration: 4.0 Hours
This cycle is very silent and ideal to use at night due to the minimum use of the drain pump
and reduced drum action with the added advantage of lower energy consumption. At the end of
the cycle the washing will be suspended in water avoiding the main noise created during the
final phase.
BABY - Temperature 40°C - Spin 800 rpm
Load: 2.0 kg
Cycle duration: 1 Hour 50 minutes
This cycle will remove all residue of detergent from the clothes to cut down the risk of allergic
reactions on delicate skin. It is also designed to reduce bacteria by using more water.
PROGRAMME
NUMBER PROGRAMME DESCRIPTION HALF LOAD EXTRA RINSE EASY IRON TIME DELAY
1 COTTON 60º YES YES YES YES
2COTTON COLOURFAST 40º YES YES YES YES
3ACRYLICS 60º YES YES YES YES
4DELICATE 40º YES YES YES YES
5FRESHUP * * *YES
6SANITARY 90º YES YES * YES
7 NIGHT CYCLE 40º YES YES * YES
8 BABY CYCLE 40º YES YES * YES
9SILKS 30º YES YES YES YES
10 WOOL 40º YES YES * YES
A HIGH RINSE YES YES YES YES
B Delicate Rinse * * * YES
C Long Spin * * * YES
D Short Spin
E DRAIN

Indesit Company
11 of 28
Service Manual UK English
WIRING DIAGRAM - SINGLE PHASE LED
3
4
2
432
5407103wd2coldfill
from V4 monophase
T
M
j9
5
4
1
2
3
4
6
7
12 3 567
5
4
3
2
1
5
4
3
2
1
21
21
1
OVERFLOW
EVL
EVP
LP
N
L
12
1
14
11 16
Pressure
Switch
1
5
R
R
R
Test
13
1
2
1
2
1
2
23
4
1
2
34
1
C
34679
1
EMPTY
FULL
COMMON
GND
RX
12
34678
R R
56
D
j5 j1 j3 j8
j10
j2
j4
12A
12A
10A
10A
8A
10A
10A
1A
1A
10w
10w
10A
1
2
RTN_IP
RTN_PORTA
8
9
j11
1
2
34
5
12345
1
12
2
j14
j13
1
2
Lav.
1
2
*
12
11
12
j12
54321
VNR
4123
5
6
LED lights
PCB with
M1
1
1
1
j15
j17
331
331
331
M2
M3
Í
Í
Í
GND
SCL
SDA
Vcc
Connector TAB
j7
SDA
SCL
GND
Vcc
j15
WASH VALVES
MAINS
INPUT
FILTER
WASH
THERMISTOR PUMP
MOTOR
ARMATURE
TACHO
TEST CONNECTOR
FABRIC COLD
NC
TF

Indesit Company
12 of 28
Service Manual UK English
WIRING DIAGRAM - SINGLE PHASE DIGIT
3
4
2
432
5407104wd2mono
from 5407103wd2coldfill
T
M
j9
5
4
1
2
3
4
6
7
12 3 567
5
4
3
2
1
5
4
3
2
1
21
21
1
OVERFLOW
EVL
EVP
LP
N
L
12
1
14
11 16
Pressure
Switch
1
5
R
R
R
Test
13
1
2
1
2
1
2
23
4
1
2
34
1
C
34679
1
EMPTY
FULL
COMMON
GND
RX
12
34678
R R
56
D
j5 j1 j3 j8
j10
j2
j4
12A
12A
10A
10A
8A
10A
10A
1A
1A
10w
10w
10A
1
2
RTN_IP
RTN_PORTA
8
9
j11
1
2
34
5
12345
1
12
2
j14
j13
1
2
Lav.
1
2
*
12
11
12
j12
j7
SDA
SCL
GND
Vcc
j15
WASH VALVES
MAINS
INPUT
FILTER
WASH
THERMISTOR PUMP
MOTOR
ARMATURE
TACHO
TEST CONNECTOR
FABRIC COLD
NC
TF
VNR
12345
LCD
DISPLAY
Module
j15
GND
SCL
SDA
Vcc
12345.

13 of 28
Indesit Company
Service Manual UK English
WIRING CONNECTION CHART
5407388wcc.ai
from 16001769800
1J1
2J1
P16
MRC
MRL
MRN
COMMON
LIVE
NEUTRAL
P11
P14
P12
R.TF.
R.R.
1J3
1J4
1J8
3J8
4J8
6J8
7J8
9J8
11J8
12J8
2J4 (YELLOW/GREEN)
2J3
3J3
4J3
5J3
6J3
- 4 -
- 3 -
- 2 -
- 1 -
- 3 -
- 2 -
- 1 -
3
1
1
3
1
3
- 1 -
- 1 -
FA4
FA1
J1
J3
1J9
2J9
3J9
4J9
5J9
6J9
7J9
8J9
9J9
IJ11
2J11
3J11
4J11
5J11
5J15
4J15
3J15
2J15
1J15
- 7 -
- 6 -
- 5 -
- 4 -
- 3 -
- 2 -
- 1 -
- 2 -
- 1 -
J9
J11
J4
J8
Motor
Pump
Display
Mains
Filter Motor
Heater
Mains
Filter
Pressure
Switch
Wash
Heater
Pre-Wash
Valve
Wash
NTC
Cold Valve
Hot Valve
(If fitted)
Live &
Neutral
MAINS FILTER
PRESSURE SWITCH & HEATER
MOTOR & PUMP
DISPLAY
EARTH CONNECTIONS
DOOR LOCK
VALVES

14 of 28
Service Manual UK
Indesit Company
English
WIRING LEGEND
AQS Aquastop solenoid valve N Neutral or Terminal board
BBuzzer or Door lock NC No spin
BF Terminal board contacts, dryer heating
element P Pressure switch
BP Door lock P1 Pressure switch 1st level
C Condenser P2 Pressure switch 2nd level
AC Condenser PA High speed potentiometer
DV Switch PB Low speed potentiometer
EF/CL Cold water/bleach solenoid valve PL Pure wool
EF/L Cold water/wash solenoid valve PM Motor thermoprotector
EF/P Cold water/prewash solenoid valve PR Timer programmer or Pressure switch
ER Cut-out heater PS Drain pump
ET Cut-out thermostat RHeating element
EV Solenoid valve Ras/RA Drying heater
EVA Drying solenoid valve RE Relay
EVC Hot water solenoid valve RR Heating element
EVF Cold water solenoid valve RV Speed regulator
EVL Wash solenoid valve S Indicator light
EVP Prewash solenoid valve SL Line indicator light
FA Noise filter SO Door indicator light
FD Delicate drying thermostat SR Heating indicator light
FE Intense drying thermostat ST Temperature selector or Stop with water
FRT Thermofuse resistance SV Spin speed selector
I Reverser T Timer contacts
I1..I2..3. Switches/deviators TA Drying timer contacts
IA On/Off switch TB Low temperature thermostat
IC Switch NC / 1/2 load TC Crosspiece earth
ID No spin switch TFL Flange earth
IE Water-economizer or NC Switch TG Main earth
IF Spin decrease switch TH Thermostat
IP Door switch TH1 Thermostat 1st temperature
IR Line switch TH2 Thermostat 2nd temperature
IS Water-stop TH3 Thermostat 3rd temperature
L Line or Lamp THF Work thermostat
LB Low level THR Adjustable thermostat
LN Normal level TM Motor earth
LS Indicator light TMB Base cabinet earth
M Earth symbol or Dryer motor TMP Motor thermoprotector
MC Spin motor or Spin winding TMS Thermostop
MI Induction motor TP Thermoprotector or Pump earth
ML Wash motor or Wash winding TPS Drain pump earth
MO Terminal board TR Heating element earth
MP Door microswitch TS Safety thermostat or Support earth
MR Microdelay device TT Timer earth
MT Timer motor TTH Thermostat earth
MV Fan TV Tub earth
MV - Ras Dryer fan (RA) ZBN Timer
Mzbn/M zbn timer motor

15 of 28
Indesit Company
Service Manual UK English
POWER MODULE CONNECTIONS
J11
J8
J10
J13
J14
J15
J9
J2
J1
J4J3
AUTO
TEST
SOCKET
(external)
EEPROM SOCKET
modules only)
(Service / spares
J5

16 of 28
Service Manual UK
Indesit Company
English
ERROR CODES & POSSIBLE CAUSES
When an error occurs the following LEDs will flash indicating a fault.
Refer to the chart below for the error code definitions.
LED DISPLAY MODELS
DIGIT DISPLAY MODELS F01 Motor triac short circuit: Check motor
and module connections
F02 Motor jammed / tacho detached: Check
motor and module connections
F03 NTC short/open circuit: Check thermistor
and module connections
F04 Pressure switch jammed on empty:
Check switch and module
F05 Pressure switch jammed on full or pump
blocked: Check pump and switch
F06 N/A
F07 Heater relay stuck: Check heater and
module connections
F08 Heater relay stuck: Check pressure
switch, heater and module connections
F09 Setup error: Check Eeprom
F10 Pressure switch not sensing: Check
switch and module connections
F11 Pump cannot be activated: Check pump,
connections and wiring
F12 No communication between cards:
Check module connections
F17 Door lock error: Check door, door lock
and module connections
F18 Communication error (3 phase motor):
Replace power board
LED 1
LED 2
LED 3
LED 4
LED 5
FAULT LED COMBINATION
LED 5 LED 4 LED 3 LED 2 LED 1
F01 Off Off Off Off On
F02 Off Off Off On Off
F03 Off Off Off On On
F04 Off Off On Off Off
F05 Off Off On Off On
F06 Off Off On On Off
F07 Off Off On On On
F08 Off On Off Off Off
F09 Off On Off Off On
F10 Off On Off On Off
F11 Off On Off On On
F12 OffOnOnOffOff
F17 On Off Off Off On
F18 On Off Off On Off
Fault Codes
are Displayed
here

17 of 28
Indesit Company
Service Manual UK English
DISMANTLING INSTRUCTIONS
SAFETY NOTES
1. Ensure that the appliance is disconnected from the electrical supply before dismantling.
2. Beware of sharp edges on metal panels, plastic mouldings, and pressed parts.
3. Some fixings (especially those into plastic) must be tightened to the correct specification using a
suitable torque wrench.
4. Insulation resistance tests must be carried out with the pressure switch set to ensure that the water
heater is 'in-circuit' during the test.
A Table Top
1. Remove the two screws at the top rear of cabinet.
2. Slide the table top backwards to disengage the location fixings at the rear and lift off.
B Lower Rear Access Panel
1. Remove three screws from the lower rear access panel.
2. Pull the top edge of the panel out and disengage it from its location fixings along the bottom.
C Dispenser Drawer
1. Open the dispenser drawer fully.
Gently lift slightly and pull. See right.
D Console Panel
1. Remove the table top (A).
2. Remove the dispenser drawer (C).
3. Remove two top screws securing the panel to the cabinet and two screws securing the panel to the
dispenser.
4. Unplug the wiring from the cabinet side to the console PCB - taking note of position.
5. Remove two screws from the valve support plate and move the dispenser to the rear.
6. Unclip two plastic lugs securing the console panel to the front panel and lift clear.
7. Avoid unclipping and handling the control board unless absolutely necessary, as the control board
is susceptible to static electricity.

18 of 28
Service Manual UK
Indesit Company
English
E Console PCB
1. Remove the console panel (D).
2. Remove the wiring plug - taking note of position.
3. Remove the four securing screws.
F Timer Knob, Programme Dial & Potentiometer
1. Push the timer knob to release it to the operating (out position) then pull knob firmly. Note: this knob
has keyed slots to determine position for replacement.
2. Remove two screws securing the selector switch plate and carefully unclip the programme dial.
G Option Knobs & Potentiometer
1. Push the knobs to release them to the operating (out position) then pull the knob firmly from the 'D'
shaft.
2. Carefully unclip the relevant potentiometer.
H(a) Pressure Switch
1. Remove the table top (A).
2. Disconnect the wiring connection block and pressure hose.
3. Carefully unclip the bracket from the cabinet side and then unclip the switch from the bracket.
H(b) Front Panel
1. Remove the table top (A), dispenser drawer (C) and console panel.
2. Remove the door seal restraint (I) and door interlock (J).
3. Grip the appliance kickstrip at both ends and pull it off in a forward direction.
4. Remove 4 front panel fixing screws (2 bottom, 2 top).
5. Slide the dispenser housing backwards so that it clears the console backplate opening.
6. Lift the front panel upwards to disengage the four cabinet fixing pegs and lift off.
I Door Seal & Restraint:
1. Door Seal to Front Panel Fixing
The door seal is fixed to the cabinet front panel by a wire clamp and a small spring. The spring is
normally at the bottom of the door.
Carefully place a small screwdriver into one of the lugs of the spring and by stretching the spring
the wire band can be removed.
2. Drum Fixing
The door seal is fixed to the drum with a zipper retainer. After removing the front panel (Hb) remove
the zipper as shown in Fig. 1 overleaf.

19 of 28
Indesit Company
Service Manual UK English
On refitting place the strap around the door seal and tighten as shown in Fig. 2. Observe correct
seal and zipper fixing positions as shown in Fig. 3 and Fig. 4.
.
J Door Interlock
1. Remove the door seal restraint (G).
2. Peel the door sealoff the front panel, and fold it back into the
inner drum.
3. Remove 2 screws from the interlock.
4. The interlock can now be eased out, allowing access to the
wiring connection block and emergency release strap.
5. Care must be taken to ensure the correct orientation of the
wiring connection plug to prevent seriously damaging the
interlock and / or control board.
Seal to Drum fixing position Correct Zipper & Seal position
at Drum Front
Fig. 1 Fig. 2
Plastic Support
(observe position) Zipper
Fig. 3 23
Fig. 4

20 of 28
Service Manual UK
Indesit Company
English
L Front Panel
1. Remove the table top (A), dispenser drawer (C) and console panel (D).
2. Remove the door seal restraint (I) and door interlock (J).
3. Grip the appliance kickstrip at both ends tilt forwards, and pull it off in a forward direction.
4. Remove 4 front panel fixing screws (2 bottom and 2 top).
5. Slide the dispenser housing backwards so that it clears the console backplate opening.
6. Lift the front panel upwards to disengage the four cabinet fixing pegs, and lift off.
M Door Seal
1. Remove the table top (A), dispenser drawer (C) and console panel (D).
2. Remove the door seal restraint (I) 1 and 2, door interlock (J) and front panel (L).
N Drive Belt
1. Remove the table top (A).
2. Remove the lower rear access panel (B).
3. Carefully peel the belt off the motor pulley taking care not to trap fingers and using suitable
protection against sharp edges.
4. To refit the belt, place it round the motor pulley first, tie-wrap the belt onto the drum pulley, and
rotate the drum from the door aperture to move the belt into position.
5. Ensure any remaining tie-wraps are removed.
It is essential for continued safety that only a genuine spare is fitted. The belt is electrically
conductive and provides an electrical earth to prevent static built up on the inner drum assembly.
K Door Assembly
1. Open the door through 180° and remove four
screws securing the hinges to the front panel.
Ease the hinges from the panel.
2. The door trims can now be split. Lay the door
assembly face down on a suitably protected
surface and remove 6 screws securing the two
halves of the door.
3. Unclip the two halves at the hinge end and
separate a sufficient distance to slide out the
door glass.
4. When removing the hinges, note the
orientation. To remove, fold hinges inward,
slide towards each other to release other end.
See photo.
Reassemble in reverse order.
5. To fully separate the halves, slide the front
away from the handle.
6. To remove the handle or latch, slide securing
pin out noting the position of the spring and
latch.
Top Hinge removal (shown below) -
Slide towards lower hinge, twist to the left and
slide up to release.
Lower Hinge removal - Slide upwards, twist to
the right and slide down to release.