Hotpoint BD52 BD62 User manual

FULL INSTRUCTIONS FOR
INSTALLING AND OPERATING
YOUR HOTPOINT DOUBLE OVEN
MODEL
BD52
BD62

Before you operate your new
Hotpoint Double Oven
Please read these instructions fully.
1. Your oven should not be located adjacent to a gas hob/heater or eye level
grill as flames from the burners could cause damage to your oven.
2. For your own safety and to get the best results from your oven it is important
to read through this Handbook before using your oven for the first time
including the Always and Never on pages 8 and 9.
Electrical Requirements
●For your own safety, we recommend that your cooker is installed by a
competent person – such as one who is registered with NICEIC (National
Inspection Council for Electrical Installation Contracting). The cooker should
be installed in accordance with the latest Edition of the IEE Regulations.
●THE INSTALLER MUST check that the voltage shown on the rating plate
corresponds with the house electricity supply.
●The oven must be supplied via a suitable double pole isolating switch,
having a contact separation of at least 3 mm in all poles placed in a readily
accessible position adjacent to the unit.
●The maximum loading for your oven is 5.3kW.
●If the oven is to be wired into a connector unit this may be positioned
behind the oven provided the following requirements are met:
i) The connector unit must not project from the wall more than 25 mm.
ii) The top of the connector must not be more than 350 mm above the base
of the oven recess.
●After unpacking the oven stand it on the packing base in order to avoid
damage.
Electrical Connections
●Remove the terminal cover at the rear base of the oven. Pass the cable
through the cable clamp and connect to the appropriate terminals provided.
Allow sufficient cable so that the oven can be set down on the floor whilst
still connected up. Tighten the screws on the cable clamp and replace the
terminal cover. Make mains connections.
This appliance conforms to EN55014 regarding suppression of Radio
and Television reception interference.
Where a double oven is used a 32 amp double pole control switch should be
used to feed the unit using a suitable rated cable. We recommend that a
minimum of 4mm2PVC insulated twin and earth cable conforming to B.S. 6004.
●Where a hob is fitted adjacent to an oven then a 45 amp Double Pole control
switch should be used to feed both units via separate suitably rated cables.
We recommend that a minimum of 4mm2PVC insulated twin and earth
cable conforming to B.S. 6004.
2
ENSURE THAT THE OVEN IS INSTALLED BY A QUALIFIED ELECTRICIAN
FOLLOWING THE INSTRUCTIONS BELOW.
WARNINGS – INCORRECT INSTALLATION COULD AFFECT THE
SAFETY OF THE OVEN.
– THIS APPLIANCE MUST BE EARTHED.
– BEFORE CONNECTING OR INSTALLING THE OVEN THE
ELECTRICITY SUPPLY MUST BE SWITCHED OFF.
WARNING: CHILDREN SHOULD NOT BE ALLOWED TO PLAY WITH THE
APPLIANCE OR TAMPER WITH THE CONTROLS.

3
PLEASE READ THIS BOOKLET CAREFULLY.
Contents Page
Before you operate your new Hotpoint Double Oven 2
Electrical Requirements 2
Installation Instructions 4-7
For Your Safety - Always 8
Never 9
The main parts of your Double Oven 10
The cooking systems in your Double Oven 11
Before using your Oven for the first time 12
Temperature Conversion Scale 12
Controls 13-14
The Automatic Oven Timer 15-20
Grilling 21-22
Top Oven - Conventional Cooking 23
Top Oven Temperature Charts 24-25
Main Oven - Fan Grilling 26
Main Oven - Fan Grilling Roasting Chart 27
Main Oven - Fan Only 28
Main Oven - Conventional and Fan oven 29
Main Oven - Fan Oven Cookery Notes 30-31
Main Oven Temperature Charts 32-33
Circulaire Roasting 34
Circulaire Roasting Chart 35
The Slow Cook Setting 36-37
Main Oven Grilling 38
Care and Cleaning 39-41
If Something Goes Wrong 42-43
Hotpoint Service Cover 44
Key Contacts Back Cover
Retention of this Instruction Book
This Instruction Book must be kept handy for reference as it contains important
details on the safe and proper use of the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind, make
sure this Book is also provided so the new owner can become familiar with the appliance and
safety warnings.
If the Book is lost or damaged a copy may be obtained from General Domestic Appliances Ltd,
Morley Way, Peterborough, PE2 9JB.
When first using the cooker ensure that the room is well ventilated (e.g. open a window or use an
extractor fan) and that persons who may be sensitive to the odour avoid any fumes. It is suggested
that any pets be removed from the room until the smell has ceased. This odour is due to temporary
finish on oven liners and elements and also any moisture absorbed by the insulation.

4
Ensure that the electricity supply
is turned off before installing
your appliance.
IMPORTANT
DO NOT LIFT OVEN BY THE
DOOR HANDLES.
This equipment is designed
specifically for domestic purposes
and Hotpoint Limited cannot accept
responsibility if used for any other
type of application.
All electrical installations must be
carried out by a NICEIC registered
installer.
1. General
The appliance is designed for
mounting at a safe level into an
open housing which must be
secured to the backing wall.
2. Oven Unit Housing Cabinets
a. The oven unit housing cabinet
dimensions must comply with
Fig. 4. (See page 7.)
b. An air gap of 50 mm minimum
must be provided at the rear of
any top or bottom cupboards
or shelves. (See Fig. 1 page
6.)
c. Ventilation must be
unobstructed, ie. from adjacent
cabinetry. This can be done by
either raising the base of the
cabinets using the adjusting
feet (or spacers) or
alternatively by providing a
slot in the cabinet plinth to the
dimensions shown overleaf.
d. The air gap at the rear allows
the warmed air to pass out of
the inner cabinet space, but
where it is intended to fit
cupboards above the oven unit
to ceiling height it is essential
that the warmed air is
exhausted through the front of
the cabinet Fig. 1. (See page 6.)
e. If an oven unit is installed
adjacent to a tall cabinet,
steam escaping from the oven
when the door is opened could
condense on, and perhaps
stain, the adjacent surface. To
prevent permanent staining,
the adjacent surface should be
made of a material that is heat
resistant and easy to clean.
Adjacent tall cabinets should
not be deeper than the oven
housing cabinet.
IMPORTANT
It is essential that the lower
cupboard is constructed in the
manner illustrated see pages 6 and
7 ie. having side, back and roof
panels so joined as to provide no
apertures which could permit
access to the oven unit when
installed .
3. Final Installation
a. Using a spirit level, check that
the housing cabinet is level
from side to side and from
front to back in its installed
position.
b. Correct any unevenness by
placing wooden packing under
the bottom of the cabinet.
Make sure that the cabinet
rests firmly on the cabinet floor
without rocking
c. Before the oven is fitted, the
cabinet must be firmly secured
to the backing wall for stability.
Installation Instructions
WARNING: THIS APPLIANCE
MUST BE EARTHED.

5
d. The oven unit should now be
lifted (by 2 adults) into the
cabinet and pushed fully home.
e. Finally the oven unit must be
secured to the cabinet by
means of the four pozi wash
head screws, two through each
side trim.
f. REMOVE ALL PACKING
MATERIAL FROM THE GRILL
AND OVEN INTERIOR.
List of Loose Items
4 x Pozi Wash Head No. 6 x
15mm screws.
Installation Instructions

6
Installation Instructions (cont'd)
Fig. 2
Fig. 1
875mm
887mm
597mm
550mm
560mm
577mm
exc. handle
Ventilation Slot here if cabinet fits to ceiling
Ventilation Slot here if cabinet doesn't fit to ceiling
50mm
Air Gap
50mm
Air Gap
Ventilation Slot
51mm x 457mm
min. area

7
Fig. 4
560mm min
574mm max
887mm
878mm if
trim is to
overlap top
edge of
shelf
* excluding pipe
work and other
projections
Oven Door
No. 6 x 15mm
screws
(4 supplied)
Viewed down through cabinet
560mm
Fig. 3
*550mm min

8
For Your Safety, Always ...
Please read through before
operating your appliance.
ALWAYS Have your appliance
installed by
a competent engineer or
electrical contractor.
ALWAYS Ensure the appliance has
been properly earthed.
ALWAYS Remove all transportation
packing from inside the
oven/grill before switching
on for the first time.
ALWAYS Make sure you understand
the controls prior to using
them.
ALWAYS Keep children away from
the oven at all times when
oven/grilling as surfaces will
get extremely hot.
ALWAYS Remember that the oven
and utensils will be very hot
when in use.
ALWAYS Take care when opening
the door. Let the steam and
hot air escape before
removing the food.
ALWAYS Use dry quality oven gloves
for removing hot food
utensils from the oven/grill.
ALWAYS Select the correct shelf
position before turning the
oven or grill on.
ALWAYS Turn off the electricity
supply at the wall switch
before cleaning.
ALWAYS Ensure poultry is thoroughly
defrosted before cooking
well.
ALWAYS Check all controls on the
appliance are switched off
before retiring to bed or
after use.
ALWAYS Keep ventilation slots clear
of obstructions.
ALWAYS Reset the oven timer to
Manual after completing an
Automatic Cooking
Programme.
ALWAYS Take care on warm days
when using the oven for
delayed automatic cooking
as certain foods can spoil.
ALWAYS Use a thick cloth to protect
your fingers when replacing
the oven lamp.
ALWAYS Refer servicing to a
qualified appliance service
engineer.
ALWAYS Follow the guide lines for
successful defrosting when
using the fan only mode.

9
For Your Safety, Never ...
NEVER Leave children playing
unsupervised where the
oven is installed and in use.
NEVER Attempt to grill with the
grill/oven oven door
closed.
NEVER Allow children to sit or
stand on any part of the
appliance.
NEVER Store food stuffs in the
same cabinet as the oven.
NEVER Store items above an
oven that children may
attempt to reach.
NEVER Operate the oven with the
inner glass panel
removed.
NEVER Remove the oven shelves
when the oven is hot.
NEVER Use water to extinguish
oil or fat fires.
NEVER Use the oven/grill as a
space heater.
NEVER Cover oven interior and
shelves with aluminium
foil.
NEVER Heat up unopened food
containers as pressure
can build up causing the
container to burst.
NEVER Attempt to clean the oven
until the mains supply has
been switched off and the
oven is cool.
NEVER Defrost the meat and
poultry by warming
through in the oven.
NEVER Store any aerosols/
flammable liquids etc. in
adjacent cabinetry.
NEVER Store anything which
might catch fire in or near
the oven.
NEVER Operate the grill when
the ovens are set to
cook automatically.
NEVER touch any heating
elements inside the oven,
the appliance becomes
hot during use.
NEVER Use steam cleaners.

10
The main parts of your Double Oven
WARNING: DO NOT TOUCH THE GLASS DOORS WHEN THE OVEN IS IN USE AS THESE
AREAS CAN BECOME HOT.
Grill
Element
Stay clean
Liner
Fan Grill
Element
Multifunction
Selector
Main Oven
Temperature
Control
Timer
Top Oven
Temperature Control /
Grill Select
Top Oven
Pilot Main Oven
Pilot
Grill Control
Rod
Shelf
Oven
Light
Oven
Fan
Stay clean
Liner
Meat pan, Anti-splash
tray and Roasting rack
Rating Plate
Inner Door
Glass
Oven Light
Grill Pan, Anti-splash tray
and Food support
Top Oven
Door
Oven
Shelves
Main Oven
Door
NEVER line the shelves, floor or sides of the oven or grill with aluminium foil as overheating
and damage may result.

11
The Cooking Systems in your Double Oven
Your new oven is equipped with
three different cooking systems:
1. Conventional Heating
(Top Oven) - with upper and
lower heat. This system is
particularly suitable for roasting
and baking on one shelf only.
2. Grilling (Top Oven) - Has a full
width, fully controllable grill. The
grill also has an economy setting
which enables you to use just the
left section.
NOTE: The oven door should
be open when grilling.
(See page 21.)
3. Fan Cooking (Lower Oven) -
the fan oven operates by
constantly blowing heated air
from an element wrapped around
the fan into the oven. This gives
improved efficiency and, in
general, enables the use of lower
temperatures for cooking. It also
means that there is less need to
be particular about shelf
positions and that you can bake
at more than one level
simultaneously (Batch Baking).
It should be noted that at the end of a cooking period there may be a
momentary puff of steam when the oven door is opened. This will disperse in a
few seconds and is a perfectly normal characteristic of an oven with a good
door seal.
1
2
3

12
Before Using the
Oven for the First Time
Temperature Conversion Scale
Make sure the electricity supply
is switched ON.
Please note that when the double
oven is used for the first time a
slight odour may be emitted due to
the ‘burning off’ of any temporary
finish on oven fittings and elements
and the removal of moisture
absorbed by the lagging. The odour
will cease after a short period of
use.
To remove the ‘new smell’, heat up
the empty oven for 30 minutes
keeping the door closed. Ensure
that the room is well ventilated (eg,
open a window or door) and that
persons who may be sensitive to
the odour avoid any fumes. It is
suggested that any pets be
removed from the room until the
new smell has ceased.
Turn the selector switch to fan oven
function, then turn oven thermostat to
MAX. Also turn Top Oven/Grill
selector to MAX.
The oven temperature thermostat
lights will come on as well as the
interior light, oven fan and cooling fan.
The chart below gives details of
comparisons of oven settings for gas
conventional ovens and fan oven in
degrees ˚F and ˚C
CONVENTIONAL
OVEN
˚F ˚C
250 120
275 140
300 150
325 160
350 180
375 190
400 200
425 220
450 230
475 240
GAS
MARK
1/2
1
2
3
4
5
6
7
8
9
FAN
OVEN
˚C
100
120
130
140
160
170
180
200
210
220

13
The Controls
IMPORTANT
Before using your oven in the
ordinary way, ALWAYS make
sure that the timer has been set
to MANUAL operation. Unless
this is done, the main oven cannot
heat up. Before seeking assistance,
make sure this is done (refer to oven
timer operation).
Multifunction Selector
Rotate the control knob in either
direction to the required function.
Many of the functions will also require
the main oven thermostat to be set
before the oven will heat up.
Main Oven Temperature Control
This is used in addition to the
multifunction selector. This is used for
the functions: fan oven, fan grill, half
grill and full grill and conventional
oven.
Turn the control clockwise to set the
oven thermostat to the required
temperature.
If the timer is set correctly and the
selector switch set to a suitable
function an indicator light will
illuminate. This will remain on until
the oven reaches the required
temperature. This light will then cycle
on and off as the thermostat maintains
control of the oven temperature.
Top Oven Temperature Control
Turn the control clockwise to set the
top oven thermostat to the required
temperature. An indicator light will
illuminate. This will remain on until the
oven reaches the required
temperature. This light will then cycle
on and off as the thermostat maintains
control of the oven thermostat.
Grill Control
The grill control is designed to provide
variable heat control of either
both grill elements on together or the
single left-hand grill element only. Turn
the top oven control clockwise past the
temperature settings to the half grill or
full grill settings, depending on which
you require. To set the grill power, turn
the grill control to any setting 1-6. After
use always return the controls to their
off position "O".
Cooling Fan
A gentle flow of air will be blown below
the control panel when any
control is used. In some instances this
will continue after switching off.
This helps to keep the control panel
and knobs cool.
After use Always return the controls to
their off ‘O’ position.
Grill
Control
Top Oven
Temperature Control /
Grill Selector
Main Oven
Temperature
Control
Multifunction
Selector
Timer
Top Oven Pilot Main Oven Pilot

14
Multifunction Selector Switch
The Multifunction selector switch is
used when operating the main oven.
With the exception of the O position
the main oven light will remain on
when this selector switch is used.
Off
With the selector in this position the
main oven will not heat up. The timer
will still operate.
Fan Oven
The oven fan and a rear element are
controlled when this function is
selected.
Use the main oven thermostat control
to set the required temperature.
Conventional Oven
Top and base elements are controlled
when this function is selected.
Use the main oven thermostat to set
the required temperature.
Half Grill
With this function selected only the left
hand side of the grill will be on.
Use the oven thermostat control to set
the required temperature.
Oven door must be open for grilling.
Full Grill
Both left and right hand grill elements
will be on in this position.
Use the oven thermostat control to set
the required temperature.
Oven door must be open for grilling.
Fan Grill
The oven fan and fan grill element are
controlled when this function is
selected.
Use the oven thermostat control to set
the required temperature.
Oven door must be closed for fan
grilling.
Fan Only
The oven fan will operate when this
function is selected.
The oven thermostat control must be
set in the off position.
Light Only
This function switches on the oven
light only.

Oven Timer Operation
15
The oven timer offers you the following
features:
1. Time of Day
2. Automatic Cooking
3. Minute Minder
Automatic Cooking
The ovens can be controlled
automatically.
Guidance on automatic cooking
1. Select foods which will take the
same time to cook.
2. Set the oven timer so that the food
has just finished or is just about to
finish cooking on your return to the
oven. This will ensure the food has
not cooled down and does not
require reheating before serving.
3. Food should be as cold as possible
when it goes into the oven, ideally
straight from the refrigerator.
Frozen meat and poultry should be
thawed thoroughly before it is put in
the oven.
4. We advise that warm food should
never be placed in the oven if
there is to be a delay period. Stews
prepared by frying the meat and
vegetables should be cooked as
soon as possible.
5. We advise dishes containing left-
over cooked poultry or meat, for
example Shepherds Pie, should not
be cooked automatically if there is to
be a delay period.
6. Stews and joints should be cooked
by the long slow method, so
that the delay period is kept to a
minimum.
7. On warm days, to prevent harmful
bacterial growth in certain foods (ie
poultry, joints, etc) the delayed start
should be kept to a minimum.
8. Wine or beer may ferment and
cream may curdle during the
delay period, so it is best to add
these ingredients just before
serving.
9. Foods which discolour should be
protected by coating in fat or
tossing in water to which lemon
juice has been added, prior to
placing food in the oven.
10. Dishes containing liquid should not
be filled too full to prevent
boiling over.
11. Food should be well sealed (but
not airtight) in a container to
prevent the loss of liquid during
cooking. Aluminium foil gives a
good seal.
12. Ensure food is cooked thoroughly
before serving.

16
Know your Timer
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure the correct time of day is always set, before using your cooker.
SYMBOLS
A ‘bell’ symbol will light up when you select a Minute Minder Period and will
remain lit for the period set.
At the end of the Minute Minder Period, the timer will emit an audible tone and
the ‘bell’ symbol will disappear.
The ‘cookpot’ symbol will light up either:–
– When the timer is in manual mode, or
– During the actual Cook Period.
‘AUTO’ will light up:–
– When the timer is first turned on it will flash. It will go out when a time of day
is set or when the timer is set to manual.
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to indicate
that the programme has finished.
(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation,
turn the oven controls off, ensure that the correct time of day is set, and press
the “Manual” button – The ‘AUTO’ symbol will go out).
Here you can set a time period of up to 23 hours 59 minutes, that will count down.
When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.
Cook Period is the actual length of time for which, the timer will switch the oven(s) on
as part of an “Auto Cooking” programme.
(e.g. If you set 2 hours, the food will be cooked for 2 hours).
The time of day at which you want an “Auto Cooking” programme to end.
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The
timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear
a audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.
Notes:
- When setting an Auto Cooking programme you will need to set the oven
control(s) to the required temperature(s) when you set the timer.
- If an Auto Cooking programme has been set the oven(s) will only operate during
the pre-programmed time.
Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to
Manual operation.
Used to adjust the various timer function settings.
Minute Minder
Button
Cook Period Button
End Time Button
Manual Button
“+” and “–” Buttons
TIMER FUNCTION BUTTONS
AUTO COOKING PROGRAMME

17
Electronic Clock & Automatic Oven
Timer Operation
SETTING THE TIME OF DAY
Step 1 Make sure all oven controls are turned Off.
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and the Auto symbol,
flashing intermittently.
Step 4 Press & hold in both the Cook Period & End Time buttons together.
Step 5 With the Cook Period & End Time buttons still held in, press either the “+”
or “–” buttons to set the correct time of day.
Step 6 Release all the buttons simultaneously.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4, 5 & 6 above.
Note: You cannot adjust the time of day if the timer has been set for an
Auto Cooking Programme.
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
Step 2 Press and hold the Minute Minder button.
Step 3 With the Minute Minder button held in, set the required Minute Minder
period using the “+” and “–” buttons. A ‘bell’ symbol will light up.
Release all buttons and the timer display will revert back to the time of day.
The ‘bell’ symbol will remain lit to signify that a Minute Minder period has been
set.
At the end of the set time an audible tone will be heard, and the ‘bell’ symbol will
disappear.
Step 4 To cancel the audible tone press the Minute Minder button.
Note 1 When the Minute Minder has been set, the time remaining can be checked at any
time by simply pressing the Minute Minder button.
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by
pressing and holding the Minute Minder button and then at the same time
pressing the “–” button until 0.00 appears in the display window.

18
Step 3 Press and hold in the Cook Period button.
The display will read 0.00 with the ‘cookpot’ symbol lit.
Step 4 With the Cook Period button still held in, set the required Cook Period
using the “+” and “–” buttons.
Release the buttons and the timer display will revert to the time of day with the
‘Auto’ symbol and ‘cookpot’ symbol lit.
Step 5 Press and hold in the End Time button.
The display will read the earliest possible end time for the Cook Period
that you have set above.
The ‘Auto’ symbol and ‘cookpot’ symbol will be lit.
Step 6 With the End Time button still held in, use the “+” and “–” buttons to set
the ‘End Time’ (i.e. The time you require the oven to switch off).
Release all the buttons and the timer will revert back to the time of day.
The ‘Auto’ symbol will remain lit to signify that an Auto Cooking Programme has
been set. The ‘cookpot’ symbol will go out.
Step 7 Turn the oven control(s) to the required temperature, and if necessary
select the appropriate oven function.
At the end of the Automatic Cook Period the Auto Symbol will flash and an
intermittent bleeping sound will be heard.
The audible tone will continue unless cancelled.
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual
operation (see below).
Step 8 Press the Manual button, the audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 9 Turn the oven control(s) to the OFF position.
AUTO COOKING PROGRAMMES
There are two Auto Cooking programmes that can be selected using your timer:–
(a) To set the timer to switch the oven(s) On and Off Automatically
(b) To set timer to switch on immediately and OFF automatically after a set cook period.
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY
This allows you to cook at a specified time for a chosen period before the oven switches
off Automatically.
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Electronic Clock & Automatic Oven
Timer Operation

19
Step 4 Press & hold in the Cook Period button, the display will read 0.00 and the
‘cookpot’ symbol will light up.
With the Cook Period button still held in set the required Cook Period using the
“+” and “–” buttons. Example: 1hr 30 minutes (as shown).
Note: Cook Period is the length of time the food requires to cook.
Step 5 Release all buttons.
The timer display will revert to the time of day with the ‘Auto’ symbol lit &
‘cookpot‘ symbol remaining lit.
At the end of the Cook Period the ‘Auto’ symbol will flash and an intermittent
audible tone will be heard.
The audible tone will continue until cancelled. The ‘Auto’ symbol will continue to
flash until the timer is returned to Manual operation (see below).
Step 6 Press the Manual button. The audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 7 Turn the oven control(s) to the OFF position.
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET COOK
PERIOD
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven
function.
Note 1 When cooking automatically the Cook Period can be checked at any time by simply
pressing the Cook Period button.
Note 2 When cooking automatically the End Time can be checked at any time by simply
pressing the End Time button.
NOTE: The Cookpot symbol disappears
Electronic Clock & Automatic Oven
Timer Operation

20
Electronic Clock & Automatic Oven
Timer Operation
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook
Period button.
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time
button.
3. Having set a Cook Period and End Time an electronic device stores the information. The device within the
timer will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–
(a) Press & release the Manual button.
(b) Start the sequence again.
5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto’, it is likely that the electricity supply to
the oven has been interrupted. Reset the timer to the correct time of day.
Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly heated
and completely cooked.
6. To set each function always press and hold the required function button and at the same time press “+” or
“–” buttons.
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE
THE COOK PERIOD HAS FINISHED.
Step 1 Turn the oven control(s) to the OFF position.
Step 2 Press the Manual button to return the oven(s) to “Manual” operation.
The ‘Auto’ symbol will go out.
Note 1 When cooking automatically the Cook Period can be checked at any time by simply pressing
the Cook Period button.