House Beautiful Fitted Bedrooms: Pigeon Hole User manual

Fitted Bedrooms: Pigeon Hole
Assembly Instructions-Please keep for future reference
Dimensions
Width - 86.4cm
Depth - 49.0cm
Height - 43.6cm
Important–Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please return to your local store.
IM........
HHGL Limited, MK9 1BA; HHGL (ROI) Limited, D02 X576
Produced for

Safety and Care Advice
Important – Pleaseread theseinstructions fully before starting assembly
Note: If required, the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to lay out the parts before
starting assembly.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the product as close
to its final position (in the same
room) as possible.
• Assemble on a soft, level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce the
likelihood of damaging
your product, please
ensure that your power
drill is set on a low
torque setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time-to-time check that
there are no loose screws on
this product.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts.
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
Handy hints

Components - Panels
Please check you haveallthe panels listed below
If you have damaged or missing components,
please return to your local store.
Top panel x 1
(86.4 x 49cm)
1
1
Upper divisions (holes on both sides) x 2
(20 x 49cm)
4
44
Lower divisions x 2
(20 x 49cm)
3
33
Shelf (holes on both sides) x 1
(86.4 x 49cm)
2
2
3

Note: The quantities below are the correct amount to complete theassembly. In some cases more fittings
may be suppliedthan are required.
Components - Fittings
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Please check you haveallthe fittings listed below
T
A
Wooden dowels
L60mm x 4
B
Wooden dowels
L30mm x 4
4

Preparing lower
division panels
Insert 2 wooden dowels
into each lower division
panel .
Note:
You can choose to assemble this
unit directly inside the wardrobe,
or separately and then place it.
Assembly Instructions
StepStep 1
3
B
3
3
3
3
2
B
B
B
B
Step 2
Fixing lower divisions
to shelf
Connect the shelf with
the lower divisions
using the dowels.
2
3
5

2
Assembly Instructions
StepStep 3
Preparing upper
division panels
Insert 2 wooden dowels
into each upper division
panel .
4
4
4
4
4
A
A
A
A
A
Step 4
Fixing upper divisions
to shelf
Connect the shelf with
the upper divisions
using the dowels.
2
4
6

Assembly Instructions
StepStep 5
Connecting top panel
Connect the top panel
to the rest of the structure.
The structure can then be
placed into the wardrobe.
Take care when moving:
Lift the structure via the
lower divisions.
11
7

Assembly Instructions
StepStep 6
Insert the structure into
the wardrobe
Carefully insert the structure
into the wardrobe:
Note: You can place it on
top of an internal chest, or
over a shelf.
8