House Beautiful Internal Wardrobe Drawer Single User manual

Fitted Bedrooms:
Internal Wardrobe Drawer (Single/Double)
Assembly Instructions-Please keep for future reference
Dimensions
Width - 35.4 / 80.4cm
Depth - 51.6cm
Height - 15.8cm
Important–Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please return to your local store.
IM........
HHGL Limited, MK9 1BA; HHGL (ROI) Limited, D02 X576
Produced for

Safety and Care Advice
Important – Pleaseread theseinstructions fully before starting assembly
Note: If required, the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to lay out the parts before
starting assembly.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the product as close
to its final position (in the same
room) as possible.
• Assemble on a soft, level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce the
likelihood of damaging
your product, please
ensure that your power
drill is set on a low
torque setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time-to-time check that
there are no loose screws on
this product.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts.
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
Handy hints

Components - Panels
Please check you haveallthe panels listed below
If you have damaged or missing components,
please return to your local store.
Side panels x 2 (14 x 48.8cm)
1
Right spacer panel x 1
(4.0 x 31.5cm)
5Left spacer panel x 1
(4.0 x 31.5cm)
6
4Drawer bottom panel x 1
(34.0 x 50.2cm for internal single robe drw)
(79.0 x 50.2cm for double internal drawer)
Drawer back panel x 1
(14 x 35.2cm for internal single robe drawer)
(14 x 80.2cm for double internal drawer)
2
Drawer front panel x 1
(15.8 x 35.4cm for internal single robe drawer)
(15.8 x 80.4cm for double internal drawer)
3
Please check you haveallthe fittings listed below
Wooden dowels x 4
Tools required
A
E
B C
Note: The quantities below are the correct amount to complete theassembly. In some cases more fittings
may be suppliedthan are required.
D
G
Rails set x 1
Components - Fittings
Locking nuts x 8 Back fittings x 4
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Tools required
A
E
Metal dowels x 8
B
Euro screws x 4
Euro screws x 4
C
F
Phillips screwdriver (medium & large)
Flatblade screwdriver (medium)
3

Assembly Instructions
StepStep 1
3
2
Step
B
3
Step
D
D
D
Screw 8 metal dowels
into drawer front panel
and back panel .
A
2
D
D
Insert 4 locking nuts
into drawer side panels
, as shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
DD
Insert 2 wooden dowels
into drawer side panels .
Then connect them to
drawer back panel .
B
3
2
2
1
1
B
B
B
B
B
B
B
A
A
D
2
1
1
2
1
1
Fixing drawer structure
Preparing panels
4

Assembly Instructions
Step 4
12
Step 5
DD
6
Step
1
1
1
2
3
4
3
4
4
2
1
1
1
D
D
Insert 4 locking nuts
into drawer side panels
, as shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
4
3
1
A
Placing bottom panel
Slide drawer bottom panel
into grooves.
Insert 2 wooden dowels
on drawer side panels ,
as shown.
Then connect it to front
panel .
D
D
D
D
A
A
Fixing front panel
5

Carefully fix drawer bottom
panel using 4 back
fittings . Slot panel into
the grooves on drawer back
and front panel .
Once placed carefully secure
by tightening the screw.
Assembly Instructions
Step 7
Step 8
Fixing spacer panels
for rails
ATTENTION:
To avoid obstruction with
door hinges, install the
drawer starting from the 4th
hole up from the base,
as shown.
Do NOT use the following
holes:
1, 2, 3, 25, 26, 27, 40, 41, 42
DRAWER LAYOUT EXAMPLE:
(Front view)
hole 16
hole 10
hole 4
NO hole 42
NO hole 41
NO hole 40
NO hole 27
NO hole 26
NO hole 25
F
4
E
23
3
Fix spacer panels and
to the wardrobe side
panels, using 2 screws
for each one.
E
E
E
E
4
1
2
5
6
5
6
6F
F
1
2
3
Fixing bottom panel
6

Assembly Instructions
Step 9
C
C
6
C
C
5
Fixing rails
Fix rails to spacers
and , using 2 screws
for each.
G
C
5
6
7

Step 10
Step 11
To prevent the drawer from
lifting off the runner it must
be secured with the locking
mechanism.
To secure, you will need to
push the pin back towards
the runner.
Fitting drawer
Slide drawer box onto rails
until it locks into position.
Pull out the locking
mechanism to allow the
drawer to take position.
Be sure that drawer box
fits correctly, as shown.
Assembly Instructions
8

Step 12
Assembly Instructions
9
Drawer height adjustment
If you want to lift or to lower
the drawer, please rotate the
specific paddle on the rails.
(Make the same gradual
adjustment on both the rails).

Assembly Instructions
Drawer on divider storage
35.4cm drawers can also
be installed on the divider
storage unit, once inside
the wardrobe.
Repeat the previous steps
for the drawer installation.
(Return to step 8).
Avoid installing the drawer
spacers any higher than the
5th hole under the shelf, to
ensure you don't obstruct
the hinges.
65
6
F
F
1
2
3
4
ATTENTION:
Wardrobe side panel:
To avoid obstruction with
door hinges, install the
drawer starting from the 4th
hole up from the base, as
shown previously (Step 8).
Do NOT use the following
holes:
1, 2, 3, 25, 26, 27, 40, 41, 42
10