HoverSeat HSEAT-XL User manual

Sit-On-Attachment for Hoverboard Self-Balancing Electric Scooter – HoverSeat XL .
Patent Pending. All Rights Reserved. Copyright 2017. HoverSeattm is a Registered Trademark.
Thank you for purchase of sit-on-attachment for hoverboard - HoverSeat XL. Please see videos and FAQs
available on a manufacturer’s web site for additional information, set up and tips.
The HoverSeat XL is a light aluminum frame with a built-in folding seat that fits easily in the trunk of the car or
closet or can be placed vertically against wall. When you want to use it, simply attach it to the bar in the center of
your hoverboard with the specially adapted patent pending clamp, unfold chair back, and you are ready to roll!
 Navigate the hoverboard using only your feet; it can even reverse. This HoverSeat can be used on or off-
road, and can ride over grass, gravel, and packed sand when attached to large 10” wheels hoverboard.
 Use HoverSeat to tow a wheeled cart and then transport bags, boxes, groceries, or use it to transport
heavy or awkward tools. Anything with wheels can be towed behind your HoverSeat.
 Use HoverSeat to transport your hoverboard back home or back to the car, in case if battery is depleted.
WARNING: EXERCISE CAUTION AND COMMON SENSE WHEN RIDING.
The user of this product assumes all risks associated with its use. Rider assumes all risks associated with activity.
Make sure the environment is safe for riding. Make sure all bolts are secure. Inspect clamp for cracks or damages.
Use all necessary body protectors. MUST wear helmet, knee, elbow pads, wrist guard, exercise full caution when
driving, be prepared to stop. Do NOT operate where people or cars might be present. Do NOT ride on slopped
areas. Do NOT overload. Do NOT race. Do NOT lift feet of pads while driving. HoverSeat is not disability vehicle
transportation. This product should not be used by persons without excellent vision, balance, coordination, reflex,
muscle and bone strength or good decision making capability. This product should not be used by minor without
adult supervision. This product should not be used by persons unwilling or unable to take responsibility for their
own action. To minimize assumed risks, the user must wear helmet, elbow and keen pads and appropriate shoes.
Do not operate this product in traffic, wet, froze, oily or unpaved surfaces. Avoid uneven surfaces, chuckholes,
cracks and obstacles.

Sit-On-Attachment for Hoverboard Self-Balancing Electric Scooter – HoverSeat XL .
Patent Pending. All Rights Reserved. Copyright 2017. HoverSeattm is a Registered Trademark.
IMPORTANT: Please make sure all bolts are properly tightened and there are no loose parts before using
HoverSeat. Periodically inspect all bolts, especially bolts holding wheels on an axle. Tighten if needed or use
locknut liquid. Do NOT stand on HoverSeat while riding. Do NOT ride on hoverboard standing with HoverSeat
attached. Do NOT overload, max weight is 230lbs.
Do NOT ride on a roads were cars are present. Be
always prepared to stop. Helmet, knee and elbow
pads are required while riding hoverboard sit-on
attachment.
ASSEMBLY: To assemble, first insert forward pull
tube into adaptor welded to the axle, and secure
with bolt. Slide wheels over axles, install washers
and secure with bolts. Assemble folding seat by
inserting front leg tube into armrests tubes, and
then securing pre-assembled fabric seating tubes
between armrests with 4 long bolts. Secure
assembled seat to rear axle using 4 small bolts
through flanges in chair’s rear legs. Install clamp
over middle section of hoverboard and secure
with lock facing forward. Clamp should be able to
rotate around hoverboard middle. Slide bolt on
top of clamp through hole in forward pull tube and secure with provided wing nut.
RIDING: Self-balancing hoverboards have pressure sensitive pads on top. Pads will register pressure when person
is standing on top of hoverboard with both feet. To ride hoverboard while sitting, firmly place both feet on pads.
No need to press hard, just simply place both feet on pads, so that feet are touching both pads all the time. Weight
of the feet should be enough to engage sensors. If hoverboard keeps vibrating, then it possible that you might
need optional ankle weights on both feet to create enough weight to engage sensors. Keep feet flat against the
pads and do not lift feet while riding sit-on attachment until complete stop.
To start forward movement, slowly tilt feet forward without lifting sole from pads.
To stop or reverse, simply tilt feet backward. If hoverboard starts vibrating, that
means you are not holding both feet flat on pads. Make sure you are not lifting
soles of your feel while tilting them forward. Start riding slowly and then try to
stop, just to get feeling how to operate safely. Do not go fast at first, learn how to
move forward and stop. Hold on to chair in case if hoverboard stop suddenly, as
you might slide forward in this case. To make turns, simply tilt only one foot
toward direction you want to turn. There is might be short learning curve to
operate HoverSeat, but generally anyone can do it.
QUICK TIP: To make operating HoverSeat easier, re-calibrate your hoverboard such way that pads tilted toward
you instead of being horizontal. Most hoverboards can be re-calibrated with pads being under angle. To do that,
tilt hoverboard toward you and press Power button for 2-4 minutes, until beep or lights blink. Then turn
hoverboard off and back on, and now hoverboard normal operating position will be with pads being under angle
instead of being horizontal. You can always re-calibrate back to horizontal pads for riding hoverboard while
standing on it. IMPORTANT!!! DO NOT TOUCH PADS WHILE RE-CALIBRATING HOVERBOARD. THAT WILL
PERMANENTLY DAMAGE PADS SENSORS.