HP D8904 User manual

hp 72
d8904 - d8905
17-inch color monitor
15.9-inch viewable image
user’s guide
www.hp.com/go/monitors
front.fm Page 1 Thursday, April 5, 2001 4:20 PM

Notice
NoticeNotice
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.
Hinweis
HinweisHinweis
Hinweis
Änderungen vorbehalten.
Hewlett-Packard übernimmt keine Haftung für mittelbare oder unmittelbare Schäden im Zusammenhang mit der Funktionsfähigkeit oder
Verwendung dieses Geräts für einen bestimmten Zweck.
Hewlett-Packard haftet nicht für irgendwelche Fehler und mittelbare oder unmittelbare Schäden im Zusammenhang mit der Lieferung,
Funktionsfähigkeit oder Verwendung dieses Geräts.
Hewlett-Packard übernimmt keine Haftung für die Funktionsfähigkeit seiner Software auf Geräten anderer Hersteller.
Die in diesem Dokument beschriebenen Informationen sind geistiges Eigentum von Hewlett-Packard und urheberrechtlich geschützt. Alle
Rechte vorbehalten. Vervielfältigung, Bearbeitung oder Übersetzung dieser Programme ist eben-falls nur nach vorheriger schriftlicher
Genehmigung durch Hewlett-Packard gestattet.
Avertissement
AvertissementAvertissement
Avertissement
Les informations contenues dans ce document peuvent être modifiées sans préavis.
Hewlett-Packard ne donne aucune garantie de quelque sorte que ce soit concernant cette documentation, notamment, mais sans que cette
liste soit exhaustive, aucune garantie implicite de valeur marchande ou d’adéquation à un usage particulier.
Hewlett-Packard décline toute responsabilité pour toute erreur contenue dans cette documentation ou tout préjudice direct ou indirect
lié à la fourniture, la réalisation ou l’utilisation de ladite documentation.
Hewlett-Packard n’est pas responsable de l’utilisation ou de la fiabilité de ses logiciels sur des équipements non fournis par
Hewlett-Packard.
Les informations contenues dans ce document sont la propriété de Hewlett-Packard et sont protégées par les lois relatives au copyright.
Tous droits réservés. Aucune partie de ce document ne peut être photocopiée, reproduite ou traduite dans une autre langue sans l’accord
préalable et écrit de Hewlett-Packard Company.
Aviso
AvisoAviso
Aviso
La información contenida en este documento está sujeta a modificación sin previo aviso.
Hewlett-Packard no ofrece garantía alguna con respecto a este material, incluyendo, aunque sin limitarse a, las garantías implícitas de
comerciabilidad e idoneidad para fines específicos.
Hewlett-Packard no se hace responsable de los errores que pueda contener este documento ni de los daños accidentales o circunstanciales
derivados del suministro, interpretación o uso de este material.
Hewlett-Packard no asume ninguna responsabilidad por el uso o fiabilidad de su software en equipos que no hayan sido proporcionados
por Hewlett-Packard.
Este documento contiene información propiedad de HP que se encuentra protegida por copyright. Reservados todos los derechos. Se
prohibe la copia, reproducción o traducción a otro idioma de cualquier parte de este documento sin el consentimiento previo y por escrito
de Hewlett-Packard Company.
Avviso
AvvisoAvviso
Avviso
Le informazioni contenute in questo documento sono soggette a modifica senza preavviso.
Hewlett-Packard non rilascia garanzie di alcun tipo su questo materiale, incluse le garanzie implicite di commerciabilità e idoneità a scopi
particolari.
Hewlett-Packard declina ogni responsabilità di eventuali errori contenuti in questo documento e dei danni accidentali o conseguenti alla
fornitura, alle prestazioni o all’uso di questo materiale.
Hewlett-Packard non sarà inoltre ritenuta responsabile dell’affidabilità e dell’uso del proprio software su apparecchiature di altra marca.
Questo documento contiene informazioni riservate protette da copyright. Tutti i diritti sono riservati. Nessuna parte di questo documento
può essere fotocopiata, riprodotta o tradotta in altra lingua senza consenso scritto di Hewlett-Packard Company.
notice.fm Page i Thursday, April 5, 2001 5:40 PM

Aviso
AvisoAviso
Aviso
As informações contidas neste manual estão sujeitas a alterações sem aviso prévio.
A Hewlett-Packard não oferece nenhum tipo de garantia com respeito a este manual, incluindo as garantias implícitas de comercialização
e conveniência para um propósito específico, mas não se limitando a elas.
A Hewlett-Packard não deverá ser responsabilizada por erros aqui contidos ou por danos incidentais ou conseqüenciais relacionados ao
fornecimento, desempenho ou uso deste material.
A Hewlett-Packard não assume nenhuma responsabilidade pelo uso ou confiabilidade do seu software em equipamentos não fornecidos
pela HP.
Este documento contém informações proprietárias que são protegidas por direitos autorais. Todos os direitos são reservados. Nenhuma
parte deste documento pode ser fotocopiada, reproduzida ou traduzida para outro idioma sem o consentimento prévio, por escrito, da
Hewlett-Packard Company.
Ďðĺäóïðĺćäĺíčĺ
Číôîðěŕöč˙ â ýňîě äîęóěĺíňĺ ěîćĺň áűňü čçěĺíĺíŕ áĺç óâĺäîěëĺíč˙.
Hewlett−Packard íĺ ïðĺäîńňŕâë˙ĺň îňíîńčňĺëüíî äŕííîăî ěŕňĺðčŕëŕ íčęŕęčő ăŕðŕíňčé, â ňîě ÷čńëĺ ïîäðŕçóěĺâŕĺěűő ăŕðŕíňčé
âűńîęčő ęîěěĺð÷ĺńęčő ęŕ÷ĺńňâ č ńîîňâĺňńňâč˙ ęîíęðĺňíűě öĺë˙ě.
Hewlett−Packard íĺ íĺńĺň îňâĺňńňâĺííîńňč çŕ îřčáęč â ýňîě äîęóěĺíňĺ, ŕ ňŕęćĺ çŕ ńëó÷ŕéíűé čëč ïðĺäíŕěĺðĺííűé óůĺðá,
ïîëó÷ĺííűé â ńâ˙çč ń äîńňŕâęîé, čńïîëíĺíčĺě čëč čńïîëüçîâŕíčĺě äŕííîăî ěŕňĺðčŕëŕ.
Hewlett−Packard íĺ íĺńĺň îňâĺňńňâĺííîńňč çŕ ðŕáîňó ńâîčő ïðîăðŕěěíűő ïðîäóęňîâ íŕ îáîðóäîâŕíčč äðóăčő ïîńňŕâůčęîâ.
Ýňîň äîęóěĺíň ńîäĺðćčň číôîðěŕöčţ, ïîäëĺćŕůóţ çŕůčňĺ ŕâňîðńęčě ïðŕâîě. Âńĺ ïðŕâŕ çŕůčůĺíű. Íčęŕęŕ˙ ÷ŕńňü ýňîăî
äîęóěĺíňŕ íĺ ěîćĺň áűňü ńęîïčðîâŕíŕ, âîńïðîčçâĺäĺíŕ čëč ïĺðĺâĺäĺíŕ íŕ äðóăîé ˙çűę áĺç ïðĺäâŕðčňĺëüíîăî ïčńüěĺííîăî
ðŕçðĺřĺíč˙ Hewlett−Packard Company.
Hewlett-Packard France 38053 Grenoble Cedex 9 France © 2001 Hewlett-Packard Company.
notice.fm Page ii Thursday, April 5, 2001 5:40 PM

hp 72
D8904 - D8905
17-inch Color Monitor
(15.9-inch Viewable Image)
User’s Guide
0.27 mm dot pitch for
excellent graphics
Full scan screen that
gives an edge-to-edge
image
Non-glare, anti-static screen coating
Status Indicator
On/Off Switch
Image adjustment controls to operate
on-screen display menus

HP 17” Color Monitor User’s Guide
Important Safety Instructions
2EnglishEnglish
Important Safety Instructions
WARNING
For your safety always connect equipment to a grounded wall outlet.
Always use a power cord with a properly grounded plug, such as the one
provided with the equipment, or one in compliance with your national
safety standards. This equipment can be disconnected from the power
by removing the power cord from the power outlet. This means the
equipment must be located close to an easily accessible power outlet.
To avoid electrical shock, do not open the monitor's cover. There are no
user-serviceable parts inside. Only qualified service personnel should
service these parts.
Make sure your computer is powered off before connecting or
disconnecting a display peripheral.
Working in
Comfort
Thank you for selecting HP monitor equipment.
To optimize your comfort and productivity, it's important that you set
up your work area correctly and use your HP equipment properly. With
that in mind, we have developed some setup and user recommendations
for you to follow based on established ergonomic principles.
You can consult the online version of Working in Comfort preloaded on
the hard disk of HP computers, or visit HP's Working in Comfort web
site at: http://www.hp.com/ergo/
CAUTION The monitor is quite heavy (the weight is shown in the technical
specifications). We recommend you ask the assistance of a second
person when lifting or moving it.
The lightning flash with arrowhead symbol, situated within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" which may be of sufficient magnitude to constitute
a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and servicing
instructions in the literature accompanying the appliance.
!

EnglishEnglish 3
HP 17” Color Monitor User’s Guide
What Your New Monitor Offers
What Your New Monitor Offers
Your HP monitor is a 17-inch (15.9-inch viewable image), high
resolution, multi-synchronous color monitor. Multi-synchronous
means that the monitor supports a range of video modes. It is
optimized for use with all Hewlett-Packard computers.
Your HP color monitor has the following features:
•A 17-inch flat square tube with a 15.9-inch viewable image.
•0.27mm dot pitch for excellent graphics and anti-static and anti-
glare coating to minimize reflection.
•Support for 1280 x 1024 at 60 Hz.
•Image adjustment using on-screen display menus. Includes color
adjustment to optimize the quality of the image.
•Monitor power management system (VESA1standard) controlled
from suitably equipped HP computers to automatically reduce the
power consumption of the monitor. Complies with the Energy Star
Computers Program initiated by US EPA2. As an ENERGY partner,
HP has determined that this product meets the ENERGY STAR
guidelines for energy efficiency3.
•Monitor Plug and Play capability (VESA DDC1/2B standard) that
enables the monitor to identify itself to suitably equipped HP
computers.
•Compliance with ISO 9241-3/-7/-8 ergonomic standards.
•Complies with MPRII level B guidelines for upper limits of
electrostatic and magnetic field emissions from the Swedish
National Board for Measurement and Testing. (D8904/D8905)
•Your monitor complies with TCO99 requirements. Refer to
“TCO99 Ecology Energy Emission Ergonomics” on page 18
(D8904).
•According to GB9813-88 (Generic Specifications for
Microcomputers in China), storage humidity ranges from 8% to
85%.
1. VESA is the Video Electronics Standards Association.
2. The US EPA is the United States Environmental Protection Agency.
3. ENERGY STAR is a US-registered service mark of the USEPA.

HP 17” Color Monitor User’s Guide
Setting Up Your Monitor
4EnglishEnglish
Setting Up Your Monitor
Attaching the Tilt and Swivel Base
Your display has a tilt and swivel base. To fit the swivel base:
1Turn the monitor on its side (never on the screen). Identify the front
of the base.
2Locate the slots in the underside of the monitor.
3Slide the base towards the front of the monitor until the locking tab
on the base clicks into place.
Where to Place the Monitor
Place your monitor on a flat sturdy surface. Ensure the operating site is
free from excessive heat, moisture, dust and sources of electromagnetic
fields. Sources of electromagnetic fields include transformers, motors,
and other monitors. Avoid exposing the monitor to direct sunlight.
1
2
3
2

EnglishEnglish 5
HP 17” Color Monitor User’s Guide
Setting Up Your Monitor
Connecting the Cables
CAUTION Before you connect any cables or install your HP monitor, refer to the
safety instructions at the beginning of this manual. Refer to the user
manual which accompanies your computer and video adapter to
ensure this equipment is correctly installed.
1Ensure your computer is switched off.
2Connect the video cable (it has a 15-pin plug) to the video outlet
on your computer. Tighten the thumbscrews on the plug.
3Connect the power cord to the monitor.
4Plug the power cord into the power outlet.
NOTE The location of your computer's video cable connector may be
different to the one shown. Refer to the manual that came with your
computer, if necessary.
1
2
3

HP 17” Color Monitor User’s Guide
Using Your Monitor
6EnglishEnglish
Using Your Monitor
1Press the Menu button to activate the on-screen display (OSD).
2Use the Menu selection and Adjustment buttons to scroll to the menu
item you require. To choose a menu item press the Menu button.
3To adjust the setting of your chosen menu item, use the Menu selection
and Adjustment buttons.Your settings are automatically saved.
4Press the Exit button to exit the on-screen display.
Refer to the table on the next page for a description of menu items.
You can directly access the brightness and contrast menu by
pressing the adjustment button which shows the brightness and
contrast icon.
NOTE Your monitor is automatically demagnetized each time it is switched on.
This ensures color purity. To maintain color purity, we recommend that
each week you switch the monitor off for at least 30 minutes.
Exit button
Menu selection and
Adjustment buttons
BRIGHTNESS
1 2
::
Note:
Note:Note:
Note: Please check your monitor to determine
the OSD (right) that applies to you.
On/Off button
Status
Indicator
On-Screen Menu (OSD)
Menu button

EnglishEnglish 7
HP 17” Color Monitor User’s Guide
Using Your Monitor
Use the table below to determine which menu item you require:
Menu Item Use to Adjust...
D8904/5
D8904/5D8904/5
D8904/5 D8904
Brightness the brightness (image black level).
Contrast the contrast (image white level).
H-Center the horizontal position of the displayed image.
H-Size the horizontal size of the displayed image.
V-Center the vertical position of the displayed image.
V-Size the vertical size of the displayed image.
Zoom the size of the displayed image.
Pincushion the vertical edges if they appear to curl inwards or
outwards.
Trapezoid the vertical edges if they do not appear to be parallel.
Pinbalance the vertical edges if they appear to curl to the left or right.
Parallelogram the vertical edges if they appear to tilt to the left or right.
Rotation the displayed image if it appears to be rotated.
Color
Temperature
the recommended color temperature setting (blue level).
the color temperature of your monitor.
the recommended color temperature setting (red level).
Language the language used in the on-screen display.
Display
Frequency
the frequency of your display.
Degauss unwanted magnetism that can result in color impurity.
Vertical Moire the effects of vertical screen ripple.
Horizontal
Moire
the effects of horizontal screen ripple.
Recall geometry settings preset at factory.
Exit to exit the on-screen display.
6500
9300
Exit Menu

HP 17” Color Monitor User’s Guide
Setting the Amount of Displayed Information
8EnglishEnglish
Setting the Amount of Displayed Information
It is recommended that you use a resolution of
It is recommended that you use a resolution ofIt is recommended that you use a resolution of
It is recommended that you use a resolution of 1024 x
1024 x1024 x
1024 x
768 a 768 a768 a
768 at 85 Hz.
t 85 Hz.t 85 Hz.
t 85 Hz.
This gives easy-to-read characters, a large amount of displayed
information and a flicker-free image.
You can make adjustments to the displayed image which are
automatically saved for the resolution you are using. For example, if you
adjust your monitor when working in SVGA, those settings are saved for
SVGA. If you then work in VGA and change the image settings, they are
saved for VGA. The next time you switch back to SVGA your previous
settings are used automatically.
To find out which resolutions are supported by your monitor, refer to
“What Video Modes are Supported” on page 9. To change the screen
resolution, please refer to the manual that came with your computer or
your operating system documentation.
Your monitor has a Plug and Play capability (VESA DDC1/2B standard)
which enables it to identify itself to suitably equipped HP computers.
This will automatically give you the best refresh rate for the resolution
that you have set. Also, by using the appropriate software (when
available) you can adjust the monitor settings directly from your
computer.

EnglishEnglish 9
HP 17” Color Monitor User’s Guide
Supported Video Modes
Supported Video Modes
Your monitor supports the video modes shown in the table below.
CAUTION Selecting a video mode on your computer with a screen resolution
and image refresh rate combination higher than 1280 × 1024 at 60 Hz
can damage your monitor. Selecting a video mode not supported by
your monitor will cause your monitor screen to go blank.
Minimizing Eye Strain
To avoid screen flicker and minimize eye strain, use the highest
supported image refresh rate for the chosen resolution. It is
It isIt is
It is
recommended that you use a refresh rate of 85 Hz.
recommended that you use a refresh rate of 85 Hz.recommended that you use a refresh rate of 85 Hz.
recommended that you use a refresh rate of 85 Hz. The image
refresh rate is the number of times per second that the image is
refreshed.
Minimizing Energy Consumption
If your computer supports VESA monitor power management
(available on many HP computers), you can minimize the power
consumed by the monitor. There are two power saving modes:
•Suspend mode1(uses less than 15W). In this mode, the monitor's
front panel indicator light is amber.
•Active off mode2(uses less than 5W). In this mode, the monitor's
front panel indicator light is amber.
To set these power saving modes, refer to the manual that came
with your computer. If your screen is not displaying an image,
check the front panel indicator light first as your monitor may be
in a power saving mode.
Screen Resolution Image Refresh Rate
640 × 350 70 Hz
640 × 400 70 Hz
640 × 480 60, 75, 85 Hz
800 × 600 60, 75, 85 Hz
1024 × 768 60, 75, 85 Hz
1280 × 1024 60 Hz
1.Suspend mode is activated when vertical sync is cut by the video controller.
2.Active off mode is activated when both vertical and horizontal sync are cut by the video
controller.

HP 17” Color Monitor User’s Guide
Troubleshooting
10 EnglishEnglish
Troubleshooting
Before calling Hewlett-Packard check the following items:
No picture and LED is off.
No picture and LED is off.No picture and LED is off.
No picture and LED is off.
•Check if monitor is switched ON.
•Check if power cord is properly connected.
•Check if electrical outlet is connected.
•Test if monitor works on another computer previously set to
monitor’s supported resolution.
No picture and LED is on.
No picture and LED is on.No picture and LED is on.
No picture and LED is on.
•Check if monitor is not in power saving mode.
•Adjust contrast and brightness through the On-Screen Menu (OSD)
using the control buttons.
•Check if computer is switched on.
•Check if video cable has no bent pins.
•Test if monitor works on another computer previously set to
monitor’s supported resolution.
Colors are not pure.
Colors are not pure.Colors are not pure.
Colors are not pure.
•Degauss your monitor.
•Shut down your monitor and switch it on after 30 minutes.
Picture is not centered.
Picture is not centered.Picture is not centered.
Picture is not centered.
•Adjust picture through the On-Screen Menu (OSD) using the control
buttons.
Picture is fuzzy.
Picture is fuzzy.Picture is fuzzy.
Picture is fuzzy.
•Use the Recall function.
•Reduce contrast through the On-Screen Menu (OSD) using the
control buttons.
•Adjust moire reduction to zero.

EnglishEnglish 11
HP 17” Color Monitor User’s Guide
Technical Specifications
Technical Specifications
PICTURE TUBE
Size 17-inch flat square tube
15.9-inch viewable image (15,9”)
Phosphorous Red, Green, Blue P22 (medium short
persistence)
Dot pitch 0.27mm (0,27mm)
Face Plate Anti-glare, anti-static, screen coating
INPUT SIGNAL Video 0.7V p p analog RGB
(0,7V)
Synchronization TTL level separate synchronization
(negative/positive)
INTERFACE Input Connector 15-pin mini D-SUB
SCANNING FREQUENCY Horizontal 30 to 95 kHz
Vertical 50 to 160 Hz
DISPLAY SIZE 324 x 243 mm ±1mm maximum viewable size
MAX RESOLUTION 1280 x 1024 (60Hz)
RECOMMENDED
RESOLUTION
1024 x 768 (85 Hz)
WARM-UP TIME 30 minutes to reach optimum performance level
PIXEL CLOCK 203 MHz
POWER SOURCE AC 100 to 240 V, 50 to 60Hz
Current 1.5 A (1,5A)
OPERATING
ENVIRONMENT
Temperature 0°C to 40°C
Humidity 10% RH through 80% RH (without
condensation)
CABINET DIMENSIONS 451 (H) ×420 (W) ×430 (D) mm (including pedestal)
WEIGHT 15Kg
TILT/SWIVEL STAND Tilt Angle - 5° to +13.5° (13,5°)
Swivel Angle ±45°
POWER MANAGEMENT
On Mode < 75W
Standby Mode < 15W
Suspend Mode < 15W
Off Mode < 5W

HP 17” Color Monitor User’s Guide
Care and Cleaning
12 EnglishEnglish
Care and Cleaning
Do not place anything on top of the monitor. Doing so may block the
monitor vents and cause damage to the monitor due to overheating. Do
not let liquid get on or into the monitor. To maximize screen life and
prevent damage to the picture tube (such as burned phosphor due to
leaving the same image on the screen for a long time), it is
recommended that you:
•Use the monitor power management system (on HP computers) or a
screen saver program.
•Avoid setting contrast and brightness to their maximum levels for
prolonged periods.
•If you do not have a power management system or a screen saver
program, switch the monitor off or reduce the brightness and
contrast to minimum levels when the monitor is not in use.
Your monitor has an anti-glare, anti-static screen coating. To prevent
damage to the monitor screen's coating, use a regular household glass
cleaner when cleaning the screen. To clean the screen:
1Switch the monitor off and remove the power plug (pull out the plug,
not the cable).
2Wet a soft cotton cloth with the cleaning solution and gently wipe the
screen. Do not spray cleaner onto the screen because the cleaner may
drip inside the monitor.
3Dry with a clean, soft cotton cloth. Do not use cleaning solutions
containing fluoride, acids or alkalis.
Environmental Information
HP has a strong commitment toward the environment. Your HP monitor
has been designed to respect the environment as much as possible.
HP can also take back your old monitor for recycling when it reaches
the end of its useful life. In fact, HP has a product take-back program in
several countries. The collected equipment is sent to one of HP's
recycling facilities in Europe or the USA. As many parts as possible are
reused. The remainder is recycled. Special care is taken for batteries
and other potentially toxic substances, which are reduced to non-
harmful components through a special chemical process. If you require
more details about HP's product take-back program, contact your
dealer or your nearest HP Sales Office.

EnglishEnglish 13
HP 17” Color Monitor User’s Guide
Hardware Warranty
Hardware Warranty
HP General Hardware Warranty
General
This HP Monitor Hardware Warranty Statement gives you, the customer,
express warranty rights from HP, the manufacturer.
FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND:
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO
THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT
OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY
RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
THE LAWS OF YOUR COUNTRY MAY PROVIDE FOR DIFFERENT
WARRANTY RIGHTS. IF SO, YOUR AUTHORIZED HP DEALER OR HP
SALES AND SERVICE OFFICE CAN PROVIDE YOU WITH DETAILS.
Warranty repair or replacement.
Hewlett-Packard (HP) warrants this monitor hardware product, or accessory
against defects in materials and workmanship for the applicable warranty
period stated above, commencing from the date of delivery of the product to
the end-user customer.
HP does not warrant that the HP hardware will operate uninterrupted or
error free.
Model Warranty Period Service Provided
D8904
D8905
3 years - unless original end-user
customer has otherwise agreed to
a shorter period of warranty at the
time of purchase.
Rest of World:
Rest of World:Rest of World:
Rest of World: On-site service for
first year and return to HP or
repair-authorized service center for
the following two years.
A
US and Canada only:
US and Canada only:US and Canada only:
US and Canada only:
Return to
HP or a repair-authorized service
center for three years.
B
Europe only:
Europe only:Europe only:
Europe only: Next Business Day
On-site Exchange (swap-out).
E
1 year Japan:
Japan:Japan:
Japan: return to HP or a repair-
authorized service center for one
year.
D

HP 17” Color Monitor User’s Guide
Hardware Warranty
14 EnglishEnglish
If, during the product warranty period, HP is unable, within a reasonable time,
to repair or replace your product to the condition as warranted, you will be
entitled to a refund (in the amount of the product purchase price) upon prompt
return of the product to your authorized HP dealer or other HP designate.
Unless otherwise stated or agreed upon in writing with HP, all hardware
components must be returned for refund with the entire system process unit.
HP software is covered by the HP Software Product Limited Warranty located in
your HP product manual. Unless otherwise stated, and to the extent permitted
by local law, hardware products may contain remanufactured parts (equivalent
to new in performance) or parts which may have been subject to prior
incidental use. HP may repair or replace hardware products (i) with products
which are equivalent in performance to the products being repaired or replaced
but which may have been subject to prior use, or (ii) with products which may
contain remanufactured parts equivalent to new in performance or parts which
may have been subject to prior incidental use.
Proof of Purchase and Warranty Period
In order to receive service or support for your hardware product for the
warranty period, proof of the original purchase date of the product may be
required in order to establish the delivery date of your product. If the delivery
date is not available, either the purchase date or the manufacturer's date
(located on the product) becomes the beginning of the warranty period.
Limitation of Warranty
Warranty does not apply to defects resulting from: (a) improper or inadequate
maintenance or calibration; (b) software, interfacing, parts or supplies not
supplied by HP; (c) unauthorized repair, maintenance, modification or misuse;
(d) operation outside of the published operating specifications for the product;
(e) improper site preparation or maintenance; or (f) such other exclusions as
may be expressly set forth in this Warranty Statement.
HP MAKES NO OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR
ORAL, WITH RESPECT TO THIS PRODUCT.
TO THE EXTENT ALLOWED BY APPLICABLE LOCAL LAW, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY
SET FORTH ABOVE.
Limitation of Liability and Remedies
TO THE EXTENT ALLOWED BY APPLICABLE LOCAL LAW, THE REMEDIES
IN THIS WARRANTY STATEMENT ARE YOUR SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL HP BE LIABLE FOR LOSS OF DATA OR
FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGE, WHETHER BASED ON WARRANTY CONTRACT, TORT, OR ANY
OTHER LEGAL THEORY.
The foregoing limitation of liability shall not apply in the event that any HP
product sold hereunder is determined by a court of competent jurisdiction to be
defective and to have directly caused bodily injury, death, or property damage.
To the extent allowed by applicable local law, HP's liability for property damage
does not exceed the greater of $50,000 or the purchase price of the specific
product that caused such damage.

EnglishEnglish 15
HP 17” Color Monitor User’s Guide
Regulatory Information
Regulatory Information
DECLARATION OF CONFORMITY
According to ISO/IEC Guide 22 and CEN/CENELEC EN 45014
Manufacturer's Name: Hewlett-Packard France
Manufacturer's Address: 5, Avenue Raymond Chanas - EYBENS
38053 GRENOBLE CEDEX 09 -FRANCE
Declares, that the products:
Product Name: 17-inch (crt) Color Monitor
Model Number: D8904** D8905** (appear on the rear identification label).
(if applicable, add: Product Options
Product OptionsProduct Options
Product Options)
Conform(s) to the following Product Specifications:
SAFETY -International: IEC 60950:1991 + A1 + A2 +A3 +A4 / GB4943-1995
-Europe: EN 60950:1992 + A1 + A2 +A3 +A4+A11
ELECTRO MAGNETIC COMPATIBILITY
- CISPR 22:1997 / EN55022:1998 Class B
- CISPR 24: 1997 / EN55024:1998
- IEC 61000-3-3:1994 / EN61000-3-3:1995
- GB9254-1998
- FCC Title 47 CFR, Part 15 class B1)
- ICES-003, Issue 3
- VCCI-B
- AS/NZ 3548:1995
Products bearing the CE marking(2) also comply with: IEC 61000-3-2:1995 / EN 61000-3-2:1995 + A14
Those products comply with requirements of the following Directives and carry the CE marking accordingly: EMC Directive
89/336/EEC and Low Voltage Directive 73/23/EEC, both amended by the Directive 93/68/EEC.
1) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
2) All products sold in the European Economic Area (EEA) bear the CE Marking.
Grenoble, February 2001
Didier CABARET
Quality Manager
F
FF
For Compliance Information ONLY, contact
or Compliance Information ONLY, contactor Compliance Information ONLY, contact
or Compliance Information ONLY, contact:
:::
USA contact: Hewlett-Packard Company, Corporate Product Regulations Manager, 3000 Hanover
Street, Palo Alto, CA 94304. (Phone [phone]).

HP 17” Color Monitor User’s Guide
Regulatory Information
16 EnglishEnglish
Notice for the USA: FCC Class B Statement
Federal Communications Commission Radio Frequency Interference Statement Warning:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the distance between the equipment and the receiver.
•Connect the equipment to an outlet on a different circuit to the one the receiver is
connected to.
•Consult your dealer or an experienced radio/TV technician for help.
Hewlett-Packard's FCC Compliance Tests were conducted using HP-supported peripheral
devices and HP shielded cables, such as those you receive with your system. Changes or
modifications not expressly approved by Hewlett-Packard could void the user's authority
to operate the equipment.
Safety Warning for USA
If the power cord is not supplied with your monitor, select the proper power cord
according to your national electric specifications.
•USA: use a UL listed SVT detachable power cord.
Hewlett-Packard’s system verification tests were conducted with HP-supported
peripheral devices and HP shielded cables, such as those you received with your system.
Cables used with this computer must be properly shielded to comply with the
requirements of the FCC.
Changes or modifications not expressly approved by Hewlett-Packard could void the user’s authority to
operate the equipment.
Notice for Canada
This Class “B” digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme a la norme NMB-003 du Canada.
Notice for Korea
Notice for Japan

EnglishEnglish 17
HP 17” Color Monitor User’s Guide
Regulatory Information
Notice for Germany:
Geräuschemission
Lärmangabe nach Maschinenlärmverordnung - 3 GSGV (Deutschland)
LpA < 70db am Arbeitsplattz normaler Betrieb nach EN27779: 11.92.
X-Ray Radiation Notice
When operating, this product emits x-rays; however, it is well shielded and meets the
safety and health requirements of various countries, such as the Radiation Act of
Germany and the Radiation Control for Health and Safety Act of the United States.
Radiation emitted by this product is less than 0.1mR/hr (1uSv/hr) at a distance of 10
centimeters from the surface of the cathode ray tube. The x-ray radiation primarily
depends on the characteristics of the cathode ray tube and its associated low voltage
and high voltage circuitry. Internal controls have been adjusted to ensure safe
operation. Only qualified personnel should perform any internal adjustments as
specified in the service manual for this product. Replace the cathode ray tube with an
identical CRT only.