HP P5389A - Intel Pentium III-S 1.4 GHz Processor... User manual

HP Server Ultra3
Non-hot Swap
(68-pin) Hard Disk Drive
Installation Guide
HP Part Number 5990-2610
Printed in January 2002

ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall not
be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced, or
translated to another language without the prior written consent of Hewlett-
Packard Company.
NetWare®and UnixWare®are registered trademarks of Novell, Inc. Microsoft®
Windows NT, NTAS®, MS-DOS and Windows 2000®are registered trademarks
of Microsoft Corporation. SCO®UNIX®is a registered trademark of The Santa
Cruz Operation, Inc. Banyan®and VINES®are the registered trademark of Banyan
Systems Incorporated. OS/2is the registered trademark of the International
Business Machines Corporation. 3M® is a registered trademark of Minnesota
Mining and Manufacturing Company. TorxTM is a registered trademark of
CamCar/Textron, Inc. SCSI SelectTM is a registered trademark of Adaptec, Inc.
Linux®is a registered trademark of Linus Torvalds.
Hewlett-Packard Company
Network Server Division
Technical Communications/MS 45SLE
10955 Tantau Avenue
Cupertino, CA 95014 USA
© Copyright 2002, Hewlett-Packard Company.
Audience Assumptions
This guide is for the person who installs, administers, and troubleshoots LAN
servers. Hewlett-Packard Company assumes you are qualified in the servicing of
computer equipment and trained in recognizing hazards in products with
hazardous energy levels.

iii
It is HP's position that the HP Server product line being acquired is normally
located in spaces frequented only by service personnel for maintenance, repair or
occasional monitoring. Pursuant to FAR 39.204(d), this product is not required to
comply with the accessibility standards at 36 CFR part 1194 published under
Section 508 of the Rehabilitation Act.

iv

v
Contents
1Prepare Drive for Installation..........................................................................1
Introduction........................................................................................................1
General Installation Steps .............................................................................1
Step 1: Prepare for Installation..........................................................................2
Tools You Need.............................................................................................2
Setup Information You Need.........................................................................2
Unpack the Drive...........................................................................................3
Step 2: Determine the Drive Type ..................................................................... 3
Step 3: Set the SCSI Address ...........................................................................8
Step 4: Continue Installation............................................................................16
2Mount the Drive in the Server L or T Series................................................17
Step 1: Mount the Drive in the System ............................................................17
Step 2: Connect the Drive Activity Light...........................................................18
Step 3: Connect the Drive................................................................................22
Step 4: Configure the Drive .............................................................................23
AJumper Settings............................................................................................. 25
Jumper Legend................................................................................................25
BReturning HP Hard Disk Drives.................................................................... 27
CWarranty and Support................................................................................... 29
Hardware Warranty..........................................................................................29
HP Repair and Telephone Support..................................................................29
Index....................................................................................................................31

vi

1
1 Prepare Drive for Installation
Introduction
This chapter describes the tools, setup information and the steps necessary to
install a 68-pin SCSI hard disk drive into an HP Server. The drives documented in
this guide are listed in Table 1-1.
Table 1-1. Hard Disk Drive Product Numbers
HP Product Number Capacity RPM
P1167A 18.2 GB 10000
P4616A 18.2 GB 10000
P1169A 36.4 GB 10000
P3578A 73.4 GB 10000
These HP Ultra3 drives can operate in either Single-Ended (SE) mode as Ultra
drives with a maximum bus data rate of 40 MB/sec or in Low-Voltage Differential
(LVD) mode as Ultra3 drives with a maximum bus data rate of 160 MB/sec. The
terminator on the cable, other drives on the bus, and/or the host controller card,
determines whether the drive runs in SE or LVD mode.
NOTE For any drive to run in LVD mode, all SCSI components on
that bus must be in LVD mode.
General Installation Steps
In general, the steps for installing a hard drive are shown below. Please refer to the
detailed instructions in each step before attempting to install your drive.
1. Prepare for Installation
2. Determine the Drive Type
3. Set the SCSI Address
5. Mount the Drive in the System
6. Connect the Drive Activity Light (if appropriate)
7. Connect the Drive
8. Configure the Drive
NOTE Drives with the same product number can be of different types
and require different jumper settings. Match your drive with the
type shown in the figures before installation.

Chapter 1 Prepare Drive for Installation
2
Step 1: Prepare for Installation
Gather the tools and the setup information you need to install the drive, before
removing the drive from its packaging.
Tools You Need
To install the disk drive, you need the following tools:
•Tweezers, needle-nose pliers or a similar tool for setting configuration
jumpers.
•A TorxTM T-15 screwdriver or a regular blade screwdriver.
Setup Information You Need
Before you begin, you need the following setup information:
•The HP Operations and Maintenance Guide for your system or
Information Assistant on the HP Server Navigator CD-ROM.
•The SCSI addresses available in your system. (Refer to your system in
Information Assistant on the HP Server Navigator CD-ROM for
information on determining available SCSI addresses.)

Chapter 1 Prepare Drive for Installation
3
Unpack the Drive
CAUTION Shock: Hard disk drives are very susceptible to mechanical
shock and can be damaged by a drop as short as one-quarter of
an inch (.64 cm). Take care when unpacking and handling the
disk drive. If the drop would crack an egg, it will damage the
drive.
Static: Protect the hard disk drive from static electricity by
leaving it in its antistatic bag until you are ready to install it.
Use an antistatic wrist strap and a grounding mat (3M
8501/8502/8505 or equivalent). If an antistatic work area is
not available, touch any unpainted metal surface to discharge
static electricity before handling the drive.
When you remove the hard disk drive from the antistatic bag,
handle it only by the frame. Do not touch the electrical
components. Place the drive on the antistatic bag whenever
you set it down.
After gathering the information and tools:
•Remove the drive from the packaging.
Step 2: Determine the Drive Type
The type of the drive varies and drives with the same part number may be of
different types.
•Match the drive you unpacked with the type of drive shown in Figure 1-1.

Chapter 1 Prepare Drive for Installation
4
Figure 1-1. Identification of the Different Types of Drives (1 of 2)