HP 5400R zl2 Series User manual

HPE 5400R zl2 Switches Quick
Setup Guide and Safety/Regulatory
Information
*5200-2721*
Part Number: 5200-2721
Published: October 2016
Edition: 2, Printed in Singapore

1
The drawings used in this document are for illustration purposes only and may not exactly match
your particular switch.
For complete installation instructions, see the HPE 5400R zl2 Installation and Getting Started
Guide on the Hewlett Packard Enterprise Networking Web site at: http://www.hpe.com/
networking/support
Auto search on “zl modules,” and select your module from the list. Click Display selected, and
then click on the links that have Manuals listed to get on to the webpage that lists the available
manuals.
Rack mounting instructions
1.(These drawings show a 6-slot chassis, but the
procedures are the same for the 12-slot chassis.)
1. 0.625 inch (1.588 cm)
2. 0,.50 inch (1.27 cm)
Before installation, read Section .
1. Determine position of switch in rack and install a cage
nut in the lower hole of the lowest rack unit.
2. Install a screw half-way into this cage nut.
3. Align the included Rack Mount Bracket such that the
half-hole lines up with the screw, install additional cage
nuts at each hole position in the bracket.
4. Repeat for opposite column in the rack.
5. Secure the Rack Mount Brackets to the switch with
included flat head screws.
NOTE: Use only the included 6 mm/0.24 inch flat
head screws. Using any of the 8 mm/0.31 inch
screw included in other rack mounting kits
interferes with internal components.
2.
6. Rest the switch on the two half-way installed screws
and secure the switch to the rack using the top hole
in each Rack Mount Bracket.
7. Align each Cable Manager such that two holes in the
Cable Manager align with two empty holes in the Rack
Mount Bracket and secure with two screws.
8. Snap the Cable Retainers into the arms of the Cable
Managers.
4.3.
2

1. Rack Brackets
2. Flat head Screws
6.5.
1. Install the retainer horizontally1. Pan Head Screw
2. 2.Cable Manager Rotate the retainer to the vertical position
3. Pan Head Screw
Power supply instructions
WARNING! During the installation, ensure that AC power is NOT connected to the Power
Supply.
Power Supply Slots:
•While installing multiple power supplies in a switch, Hewlett Packard Enterprise
recommends that all power supplies are the same models.
•See the HPE 5400R zl2 Installation and Getting Started Guide for selecting the correct power
cord to use with the supply.
1. Remove the slot cover plate.
2. Align the power supply in the
switch slot and insert it until the
external wall of the power supply
is flush with the switch chassis.
3. Tighten the retaining screws to
secure the power supply to the
switch.
Power supply instructions 3

1. Grounding Lug Mounting Holes
2. Power Supply Slots
Software version
For the latest software version, go to: http://www.hpe.com/networking/support
Installation notes
Transceiver operation notes
Revision “B” or later SFP transceivers only. This product requires revision “B” or later
mini-GBICs or SFP transceivers (product number ends with the letter “B” or later, for example
J4858B or J4859C). These switches do not support revision “A” mini-GBIC or SFP transceivers.
This applies only to SFP transceivers and not SFP+ transceivers.
Use only genuine Hewlett Packard Enterprise transceivers: Non-Hewlett Packard Enterprise
transceivers are not supported. Use of genuine products ensures that your network maintains
optimal performance and reliability. Should you require additional transceivers, please contact
a sales representative or an authorized reseller. For a complete list of supported transceivers,
visit the Hewlett Packard Enterprise networking Web site at http://www.hpe.com/networking/
support. Locate FAQs, and under Mini-GBICs and Transceivers, select one of the following:
•HPE 10-GbE Transceivers and Cables
•HPE Mini-GBICs and SFPs
Click on the first question in the “General product information” category.
Hot-Swapping transceivers: The transceivers that you can install in your Hewlett Packard
Enterprise switch can be “hot swapped”–removed and installed after the switch is receiving power.
You should disconnect the network cables from the transceivers before hot swapping them.
Best practice tip: After inserting a transceiver into a switch, the Mode LED will be on for two
seconds while the transceiver is initialized. Do not remove the transceiver until the Mode LED
has turned off.
When you replace a transceiver with another transceiver of a different type and then execute the
write memory command in the switch console, the switch configures the port on the new
transceiver with the default mode (speed and duplex) settings used for the new transceiver type.
The default mode for the transceivers is Auto. Note that the switch retains other port-specific
configuration settings, such as trunking Spanning Tree Protocol (STP) and VLAN values that
were configured for the previous transceiver.
Connecting the transceivers to devices with fixed configurations: For some older network
devices, including some older Hewlett Packard Enterprise devices, the default for the Gigabit-SX,
Gigabit-LX, and Gigabit-LH ports is a fixed configuration, for example 1000 Mbps/Full Duplex,
or is otherwise different from these default configurations for the transceivers, which is Auto. As
a result, those devices may not connect properly to your transceiver port; you will not get a link.
Because of these default configuration and full-duplex considerations, for best operation, you
4

should make sure that the devices connected to the transceiver ports are also configured to
Auto.At a minimum, make sure the configurations match.
NOTE: For improved cable management, install the GigT/SFP and GigT/SFP+ combination
modules on the left side of the chassis. This will improve access to the uplink ports when
the RJ45 cables are retained in the cable manager.
Module installation notes
The following cases automatically result in a change to the running-configuration on your switch.
•Replacing a module with another module of a different type and then rebooting the switch
•Installing a module in a slot that has not previously been used (including when you install a
module and apply power to the switch for the first time)
If you want to save such changes to the startup-configuration file, use the write memory command
in the switch’s command line interface. This causes the switch to use the current new hardware
configuration for subsequent reboots. (The switch always reboots from the startup-configuration
file.)
One of the features of your 5400R zl2 switch is the ability to “hot swap” the switch modules. You
can install, exchange, or remove modules after the switch has been powered on. Whenever a
module is installed during this process, it is initialized and tested for correct operation. During
this process, the switch Self Test LED is on. If you hot swap another module while the switch is
initializing and testing the first module, it is possible to cause the first module or the entire switch
to be reset.
To prevent the modules or switch from being reset when you must hot swap multiple modules,
follow these simple precautions: Before removing or installing any modules, make sure that all
network cables are disconnected from the module. Do not remove any modules from the switch
while the switch Self Test LED is lit.
Installation Precautions
WARNINGS
•Devices installed in a rack or cabinet should be mounted as low as possible, with the
heaviest device at the bottom and progressively lighter devices installed above.
•The rack or cabinet should be adequately secured to prevent it from becoming unstable
and/or falling over.
•Ensure a cover plate is installed on any empty switch power supply or module slot.
A cover plate is required for safe operation, and to ensure proper switch cooling.
Never have more than one power supply or module slot uncovered at a time while the
switch is powered on.
•To avoid energy and mechanical hazards, never allow any part of your body, jewelry,
tool, or other foreign object to enter any module or power supply slot.
•This unit may have more than one power supply cable. To fully power down the switch,
you must disconnect all power supply cables from the unit.
•When the HPE 5412R zl2 switches are operating in the high-line voltage range (200 -
240 V), the switch may have high leakage current depending on the power supply
configuration. Safety leakage current per cord for the three available 5400R zl2 power
supplies is 0.85 mA maximum, regardless of the power supply model. When more
than four power cords are installed in the chassis, the leakage current safety limit
threshold of 3.5 mA may be exceeded. If the switch has four or fewer power cords
installed or if the equipment is operating in the low line (100 - 130 V) voltage range,
Installation Precautions 5

no precautions are required. Use one of the following installation methods while
performing an installation, when using more than four power cords:
◦Using normal pluggable cords:
–Place the equipment in a restricted access area such as a locked closet or key card access room, the
access for which is granted only for qualified or service personnel.
–The building installation must provide a protective earth ground and a means for connection to the switch.
The service personnel must check whether the socket-outlet from which the switch is to be powered
provides a connection to the building protective earth. If not, the service personnel must arrange for the
installation of a protective earthing conductor, which shall be sized appropriately, from the grounding lug
terminal (as shown in the figure) to the protective earth wire in the building.
◦Using industrial/locking pluggable cords:
–Secure at least one of the power cord connector ends on the switch power supply using the retention clip
provided on the 5400R 2750W PoE+ power supply as displayed in the figure. When you use this option,
the restricted access caution is not required.
6

CAUTION:
•If the switch is to be shipped in a rack, use only J9852A HPE X450 4U/7U Universal 4-Post
Rack Mounting Kit for each switch. The switch is qualified for rack shipping only in Hewlett
Packard Enterprise Shock Racks.
•Ensure the power source circuits are properly grounded.
•If your installation requires a different power cord than the one supplied with the switch and
power supply, be sure the cord is adequately sized for the switch’s current requirements. In
addition, be sure to use a power cord displaying the mark of the safety agency that defines
the regulations for power cords in your country. The mark is your assurance that the power
cord can be used safely with the switch and power supply.
•When installing the switch, note that the AC outlet should be near the switch and should be
easily accessible in case the switch must be powered off.
•Ensure the switch does not overload the power circuits, wiring, and over-current protection.
Each power supply should be connected to a dedicated branch circuit to prevent tripping
building circuit breakers. To determine the possibility of overloading the supply circuits, add
together the ampere ratings of all devices installed on the same circuit as the switch and
compare the total with the rating limit for the circuit. The maximum ampere ratings are usually
printed on the devices near the AC power connectors.
•Do not install the switch in an environment where the operating ambient temperature might
exceed 45°C (113°F).
•Allow at least three inches of space around the sides and back of the switch to make sure
the air flow for the switch is not restricted.
Regulatory information
WARNING! Do not wall-mount any of the 5400R zl2 switches or bundles.
HPE 5406R zl2 (J9821A) and 5412R zl2 Switches
(J9822A) including all bundlesApplicable Products
0°C to 45°C (32°F to 113°F)Environmental Operating Temperature:
15% to 95% at 45°C (113°F) (non-condensing)Relative humidity:
-40°C to 85°C (-40°F to 185°F)Non-Operating Temperature:
15% to 95% at 65°C (149°F)Non-Operating Relative humidity:
3.1 km (10,000 ft)Maximum Operating Altitude:
NOTE: If you are using the J9830B power supply unit
with your switch, the maximum operating temperature is
reduced to 40°C between altitudes of 5000 feet (1.52 km)
and 10000 feet (3.1 km).
15.24 km (50,000 ft)Non-Operating Altitude:
EN60950-1:2006+A11:2009+A1:2010+A12:2011 /
IEC60950-1:2005; Am1:2009; CSA22.2 No. 60950-1-07
2nd; UL60950-1 2nd
Safety Standards:
EN60825-1:2007 / IEC 60825-1:2007 Class 1Lasers:
Class 1 Laser Products/Laser Klasse 1
(Use only Hewlett Packard Enterprise supported SFPs)
Regulatory information 7

Table 1 HPE 5400R zl2 Power Supplies
J9830BJ9829AJ9828AElectrical
AuxMain
115-127; 200-240
volts
115-127; 200-240
volts
110 -127 volts; 200 -
240 volts
100 -127 volts; 200 -
240 volts
AC voltage:
15.5; 8 A max15.5; 8 A max12; 6.8 A max8.5; 4.3 A maxMaximum current:
50/60 Hz50/60 Hz50/60 Hz50/60 HzFrequency range:
1400 W1100 W900 W275 WPoE output wattage
(MAX):1
1Actual power available depends on system configuration
Power cord, use one of the following appropriately for the power supplies:
J9830B Power Supply CableCountry/Region
8121-1550Australia/New Zealand
8121-1551China
8121-1554Mainland Europe/South Korea
8121-1074India
8121-15551 Japan/Thailand
8121-1287Denmark/Switzerland
8121-1549United Kingdom/Hong Kong/Singapore/Malaysia
8121-1553United States/Canada 125V
8121-1552South Africa
8120-63622 Taiwan/USA 250V
8121-1010Israel
8121-0925Argentina
8121-1101Brazil
8121-0923Chile
1Japan: NEMA 6-20P, 200V.
2Taiwan/U.S.A. 250V: NEMA L6-20P, 250V
J9829A Power Supply CableCountry/Region
8121-1476Australia
8121-1484China
8121-1479Europe/South Korea
8120-5338Japan
8121-1485Thailand/Philippines
8121-1486Denmark
8121-1480Switzerland
8121-1475United Kingdom/Hong Kong/Singapore/Malaysia
8121-1483South Africa/India
8

J9829A Power Supply CableCountry/Region
8121-1511Taiwan
8121-1478Israel
8121-1481Argentina
8121-1474Brazil
8121-1477Chile
8121-0914North America 110V
J9828A Power Supply CableCountry/Region
8121-0834Australia
8120-8707China
8120-6811Europe/South Korea
8120-4753Japan
8121-0668Thailand/Philippines
8121-0780India
8120-6814Denmark
8120-6815Switzerland
8120-6809United Kingdom/Hong Kong/Singapore/Malaysia
8120-6813South Africa
8121-0974Taiwan
8121-1035Israel
8120-6869Argentina
8121-1069Brazil
8120-6980Chile
8121-0914USA/Canada
Japan Power
Cord Warning
Interior Wiring
Warning
Russia, Belarus
and Kazakhstan
Mark of
Conformity
Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia elétrica
que possua aterramento (três pinos), conforme a Norma NBR ABNT 5410, visando a segurança
dos usuários contra choques elétricos.)
Brazil Statement
Regulatory information 9

Battery Statements
ll y a danger d'explosion s'il y a remplacement incorrect de la batterie.ATTENTION
Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé
par le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du fabricant.
The battery supplied on the management module with this product may contain perchlorate
material. Special handling may apply in California and certain other states. See http://
www.dtsc.ca.gov/hazardouswaste/perchlorate Web site for more information.
ATTENTION
CAUTION: Risk of explosion if battery on the management module is replaced by an incorrect
type. Dispose of used batteries according to the instructions.
For important safety, environmental, and regulatory information, see Safety and Compliance
Information for Server, Storage, Power, Networking, and Rack Products, available at http://
www.hpe.com/support/Safety-Compliance-EnterpriseProducts.
Documentation feedback
Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To
help us improve the documentation, send any errors, suggestions, or comments to Documentation
Feedback ([email protected]). When submitting your feedback, include the document
title, part number, edition, and publication date located on the front cover of the document. For
online help content, include the product name, product version, help edition, and publication date
located on the legal notices page.
Copyright
Copyright © 2010, 2015, 2016 by Hewlett Packard Enterprise Development LP
10