Huawei IPC6325-WD-VF User manual

IPC6325-WD-VF
IPC6325-WD-VR
Issue: 06 (2017-11-20)
版权所有 © 华为技术有限公司 2017。保留一切权利。
Copyright © Huawei Technologies Co., Ltd. 2017.
All rights reserved.
Quick Start Guide
快速入门
版本：06（2017-11-20）
Packing List and Qualification Card
装箱清单和合格证
Additional Guides Available
资料获取路径
Component
物品 PCS Component 物品 PCS
IPC
网络摄像机 1Waterproof connector for network cables
网线防水接头 1
Drilling sticker
安装定位贴纸 1Waterproof connector seal loop
网线防水接头密封圈 2
Expansion tube
膨胀管 3Crimping terminal (supporting 0.75 mm2 and 1.0 mm2 cables)
压线端子（支持0.75mm2和1.0mm2的线缆） 2
Tapping screw
自攻螺钉 3Power terminal
电源端子 1
Quick Start Guide
快速入门 1Flat-head screwdriver (the width of the head is 2.5 mm)
一字螺丝刀（刀头宽度为2.5mm） 1
To obtain the latest documents, including the
Product Documentation , Configuration
Guide , Quick Start Guide , and FOSS License Information , visit http://support.
huawei.com/enterprise and choose SUPPORT > Video Surveillance > IP Cameras.
You can also log in to http://e.huawei.com/app or scan the QR code using a
mobile phone to download Huawei Enterprise Technical Support APP. Then start this
APP and choose Video Surveillance > Cameras to obtain the latest documents.
请登录 http://support.huawei.com/enterprise网站，选择“技术支持 > 视频监控 > IP
摄像机”获取最新资料，包括《产品文档》、《配置指南》、《快速入门》和《开源软件使
用声明》等。您也可以用手机登录 http://e.huawei.com/app网站或者扫描右侧二维码，
下载“华为企业技术支持移动 APP”，选择“视频监控 > 摄像机”获取最新资料。
Huawei Enterprise
Technical Support APP
华为企业技术支持移动 APP
电子电气产品有毒有害物质申明
部件名称
有毒有害物质或元素
Pb
铅
Hg
汞
Cd
镉
Cr6+
六价铬
PBB
多溴联苯
PBDE
多溴二苯醚
结构件 ○ ○ ○ ○ ○ ○
单板/电路模块 ○ ○ ○ ○ ○ ○
线缆和线缆组件 ○ ○ ○ ○ ○ ○
纸质配件 ○ ○ ○ ○ ○ ○
○：表示该有害物质在该部件所有均质材料中的含量在GB/T 26572规定的限量要求以下。
×：表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。
This product has an environment friendly use period (EFUP) of 20 years, as shown in
the symbol on the left. Some replaceable parts have their own EFUP labels. The EFUP
is suitable only for products that work in conditions specified in the product manual.
本产品的环保使用期限为20 年，标识如左图所示。某些可更换的零部件会有一个不同的环保使
用期贴在其产品上。此环保使用期限只适用于产品是在产品手册中所规定的条件下工作。
本表格依据SJ/T 11364的规定编制。

PVC insulation tape
绝缘胶带
Wiring terminal
接线端子
Measuring tape
钢卷尺
Marker
记号笔
Hammer drill (for mounting a
camera on the ceiling or wall)
冲击钻（吊顶和墙壁安装时使用）
Claw hammer (for mounting a camera
on the ceiling or wall)
羊角锤（吊顶和墙壁安装时使用）
Phillips screwdriver (Head model: 0#,
2#; screwdriver bit length > 75 mm)
十字螺丝刀（刀头型号为：0#、2#，批
头长度大于75mm）
Cable stripper
剥线钳
RJ-45 connector crimping tool
水晶头压线钳
Interface Description/ 接口说明
NO.
序号
Item
名称
Description
说明
1LAN/POE
Indicates the network interface that supports power over Ethernet (PoE). When the power input
interface and PoE interface are connected at the same time, PoE is preferred.
网络接口。支持PoE供电。当电源输入接口和PoE同时连接时，优先PoE供电。
2
ALARM_OUT Indicates the alarm output interface. ALARM_OUT and ALARM_REF form a group of alarm
output.
告警输出接口。ALARM_OUT和ALARM_REF组成一组告警输出。
ALARM_REF
ALARM_IN Indicates the alarm input interface. ALARM_IN and GND form a group of alarm input.
告警输入接口。ALARM_IN和GND组成一组告警输入。
GND
RS485+ Indicates the RS485 interface that enables the camera and the connected device to send data to
each other in half-duplex mode through the transparent channel.
RS485接口。通过该接口，摄像机可以以半双工的方式通过透明通道与连接的设备互相传递数据。
RS485-
3VIDEO Analog video output interface. The interface supports only D1 video output.
模拟视频输出接口。该接口仅支持以D1分辨率输出视频。
4AUDIO OUT Indicates the video input/output interface. To ensure audio output quality, connect a 3.5 mm
TRS connector to the interface.
音频输入输出接口。为保证音频输出质量，请使用三段式3.5mm音频接头。
5AUDIO IN
6AC24V/
DC12V
Indicates the power input interface. This interface supports 12 V DC (9.0 V to 15.0 V) and 24 V
AC (18.0 V to 29.9 V) power input.
电源输入接口。支持DC 12V（9.0V～15.0V）和AC 24V（18.0V～29.9V）电源输入。
7GND Indicates the ground interface of an IPC.
设备接地接口。
Reset button and SD card slot/Reset 键和 SD 卡槽
Prepare for Installation Tools/ 准备安装工具
NO.
序号
Operation
操作
Description
说明
1
Use a Phillips
screwdriver to
uninstall the
transparent
cover. You can
find the reset
button, SD card
slot, focus screw
rod, and zoom
screw rod.
使用十字螺丝刀
将透明罩卸下，
即可看到重置键、
SD 卡槽、聚焦螺
杆和变焦螺杆。
SD card slot that supports only Micro SD cards of Class 6 or higher classes. You can replace a Micro
SD card only when the device is powered off. When a Micro SD card is used for the first time, log in
to the web page of the device and format the Micro SD card. For details, see Conguration Guide.
SD卡卡槽，仅支持Micro SD卡（Class 6及以上）。请在设备断电的情况下插拔SD卡，否则会造成系统异
常。首次使用时，请登录设备Web客户端，格式化SD卡，操作方法请参见《配置指南》。
2
Reset button. To restart the device, hold down the RST button for less than 3s. To restore the device
to factory defaults, hold down the RST button for at least 3s during the device running or hold down
the RST button, power on the device, and keep holding down the RST button for more than 5s.
重置按钮。运行时按住RST键短于3秒重启设备；运行时按住RST键不短于3秒或者按住RST键后上电并持续按
住RST键不短于5秒后恢复出厂配置。
3
Auxiliary focus button and indicator. After you adjust the zoom bolt to obtain the desired image
quality, press the auxiliary focus button. Then the auxiliary focus indicator blinks, for example, you
can hear beeps if the IPC is connected to an audio output cable. Adjust the focus bolt. When the
image focus is clear, the auxiliary focus indicator is steady on and you can hear a long beep.
辅助对焦按钮及辅助对焦指示灯。调整变焦螺杆获取所需画面后，再按下辅助对焦按钮，辅助对焦指示灯闪烁
（如接音频输出，可听到“滴滴”声）。调整聚焦螺杆，当画面聚焦清晰后，指示灯长亮（音频长响）。
4
Zoom screw rod. You can loosen it to adjust the angle of view and tighten it after the adjutment.
变焦螺杆（T~W）。拧松调整画面视场角，调整结束后拧紧螺杆。
5
Focus screw rod. You can loosen it to adjust the image resolution and tighten it after the adjustment.
聚焦螺杆。拧松螺杆调整画面清晰度，调整结束后拧紧螺杆。
Security Precautions/ 安全注意事项
Carefully read and strictly comply with the following instructions and pay attention to the alarm information in this manual:
请仔细阅读本说明并严格遵守，留意本手册中的所有警告信息。
• The power adapter to be used by the device must meet the input voltage and current requirements described on the device label.
设备所使用的电源适配器必须满足设备标签上注明的电源输入电压和输入电流要求。
• Install a lightning arrester and effectively ground the device shell.
请安装避雷器，设备外壳必须有效接地。
• Risk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the instructions.
如果更换不正确的电池规格会有爆炸的风险，请按制造商说明书处理使用过的电池。
• This is a class A product. In a domestic environment this product may cause radio in ference in which case the user may be
required to take adequate measures.
此为 A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对其干扰采取切实可行的措施。
• Use a soft and dry cloth when cleaning the camera body. Do not use strong and abrasive alkaline cleaner or volatile solvent such
as alcohol, benzene, or thinner.
清洁机身可用柔软的干布擦拭，请勿使用如酒精、苯或稀释剂等挥发性溶剂或者强烈的、带有研磨性的碱性清洁剂。
• Keep the device away from water or any other liquids. Take proper water-proof measures when installing the device outdoors.
禁止让任何液体流入设备中，如果安装在户外，必须做好防水措施。
• Keep the device away from heat sources, fire sources (such as heating apparatus or candles), and strong magnetic fields (for
example, high-voltage power distribution cabinet).
安放设备时请远离热源、裸露的火源（例如电暖器、蜡烛等）和强磁场环境（例如高压变电箱）。
• Avoid any unauthorized modifications on the design of the structure, security, or performance.
未经授权，任何单位和个人不得对设备进行结构、安全和性能方面的改动。
• Installation and maintenance must be performed by professional technical engineers or system installation engineers.
有关本装置的所有安装维修工作均应由专业的维修技术人员或系统安装人员来完成。
• Use product-attached auxiliaries and recommended fittings.
请使用产品配套的附件以及厂商推荐的配件。
• Carry a device by the device body. Do not pull the pigtails.
搬运设备时，使用双手合抱机身将摄像机捧起，禁止提拉尾线。
• Comply with related laws and regulations, and respect legal rights of others when using this device. Post a reminder "You have
entered the electronic surveillance area" at the most visible location if cameras are installed at public places.
使用本设备时应遵循相关的法律法规，尊重他人的合法权利。如果您在公共场所安装摄像机，请在醒目的位置给予提示：您已进入电子监控范围。
1
2
3
5
4
1
2
4
3
5
6
7
NOTE/ 说明
The color identifier of the alarm cable is subject to the actual pigtail label.
告警线缆颜色标识以实际的尾线标签为准。

A Install the SD card/ 安装 SD 卡
Install the Device/ 设备安装
1
3Connect the cables to the tails of the camera, perform insulation
operations on the cables (see Connect Cables), and put the cables
through the cable entry on the wall. Use the torque of 5 to 7 kgf.cm to
fasten the tapping screws.
将线缆与摄像机的尾线连接，对线缆进行绝缘处理（参见“连接线缆”），然
后塞入墙壁出线孔。使用 5~7Kgf.cm 的扭矩拧紧自攻螺钉。
B Surface-Mount/ 吸顶安装
2Use a Phillips screwdriver to remove the transparent cover, lightly press
the inner cover without blocking the two holes, and remove the inner
cover.
使用十字螺丝刀卸下透明罩，然后双指轻压内罩非固定卡扣位置，卸下内罩。
Use a Phillips screwdriver to remove the transparent cover, install the SD
card.
使用十字螺丝刀将透明罩卸下，插入 SD 卡。
4This camera uses the tri-axis design, allowing horizontal, vertical,
and chipset rotation. Use a Phillips screwdriver to loosen screws on
the chipset, and adjust the surveillance angle. Loosen the zoom bolt
(marked with T and W), adjust the zoom times, and tighten the zoom
bolt, as shown in step 1 in the figure. Loosen the focus bolt, adjust the
focus, and tighten the focus bolt, as shown in step 2 in the figure. After
the adjustment is complete, tighten the screws on the chipset. You
can rotate the chipset by 90° to facilitate image adjustment. After the
adjustment is complete, rotate the chipset by 90° counterclockwise to
the specified angle.
该款摄像机为三轴工艺设计，水平方向、垂直方向及机芯都可以转动。使用十
字螺丝刀将固定机芯的螺丝拧松，调整监控角度。拧松变焦螺杆（环上标有 T
和W，如图中①所示），调整放大倍数，直到满足监控需求为止，拧紧变焦螺杆，
再拧松聚焦螺杆（如图中②所示），调整画面到清晰为止，拧紧聚焦螺杆。调
整完毕后，拧紧固定机芯的螺丝。您可以先将机芯旋转 90°，以方便调整画面。
调整好画面后，再反方向旋转 90°，将机芯恢复至监控所需角度。
5Lightly press the inner cover, and fix it to the chipset. Then align the
transparent cover with the base through the tapped holes, close the
transparent cover, and use a Phillips screwdriver to tighten the screws.
双指轻压内罩，将内罩卡槽对准卡扣，固定内罩，然后将透明罩和底座的螺孔
位置对齐，合上透明罩并使用十字螺丝刀拧紧螺钉。
NOTE/ 说明
The indoor direct wall-mount method is similar to the surface-mount
installation. Install the camera on the wall by referring to B Surface-Mount.
When a camera is installed horizontally by default, the surveillance image
is displayed horizontally. Carefully adjust the surveillance angle when
installing the camera to prevent the reverse image display.
室内直接壁装方法与吸顶安装类似，请参见“B 吸顶安装”，将摄像机安装在墙壁上。
摄像机默认水平安装时，监控画面为水平显示。安装过程中，请注意调整监控角度，
避免安装完成后视频画面翻转。
12
Paste the drilling sticker in the camera installation position and ensure
that the center of the sticker overlaps the center of the cable outlet
on the wall. Obtain a drill bit with a 5 mm diameter and drill four 35
mm holes in the specified positions marked by the stickers. Use a claw
hammer to install an expansion bolt into the hole.
将安装定位贴纸贴在摄像机安装位置，贴纸中心请对准墙壁出线孔。依照贴纸
上的标注，选择直径为 5mm 的钻头，钻取深约 35mm 的导孔，并使用羊角
锤将膨胀螺栓打入钻好的孔内。

Place the ceiling-mount bracket to the required installation location,
use a marker to mark the screw installation positions and drill holes in
the marked positions.
将吊装支架放置于安装位置，使用记号笔绘制螺钉安装位置，并根据绘制的螺
钉安装位置钻孔。
Install the Device/ 设备安装
2
5
1
4Use a Phillips screwdriver to remove the transparent cover.
使用十字螺丝刀将透明罩卸下。
Align the tapped holes of the camera with installation slots on the
ceiling-mount bracket plate, thread screws through the holes, and
tighten the screws.
将摄像机的安装螺孔对准吊装支架安装盘上的对应安装槽，将螺钉穿过螺孔，
拧紧螺母。
C Indoor Ceiling-Mount/ 室内吊装
Use a claw hammer to install the expansion bolts into the holes.
使用羊角锤将膨胀螺栓打入钻好的孔内。
NOTE/ 说明
For details about subsequent installation
operations, see steps 4 and 5 in B Surface-
Mount.
后续安装的具体过程请参见“B 吸顶安装”中的
4-5步骤。
3Remove flat washers, spring washers, and nuts from the expansion
bolts. Thread the cables through the ceiling-mount bracket. Put the
four expansion bolts through the four screw holes at the bottom of the
ceiling-mount bracket, put the flat washers, spring washers, and nuts
on the expansion bolts, and tighten the nuts.
拧下膨胀螺栓上的平垫、弹垫和螺母。将需要与摄像机尾线对接的线缆穿过吊
装支架。将吊装支架底座上的 4 个螺孔套在相应的膨胀螺栓上，将平垫、弹
垫和螺母套在膨胀螺栓上，拧紧螺母。
6Align the tapped holes on the edge of the ceiling-mount bracket
plate with the tapped holes on the installation bowl, and use a Phillips
screwdriver to tighten the screws.
将安装盘边上的螺孔对准安装碗的四个螺孔，使用十字螺丝刀拧紧螺钉。

Install the Device/ 设备安装
D Indoor Wall-Mount/ 室内壁装
Connect the power cable and the ground cable. A power cable terminal supports the 1.5 mm² power cable at
most. The ground impedance must be less than or equal to 5 ohms, and the ground cable length is less than
or equal to 25 meters. Use the OT terminal with an inside diameter of 3 mm.
连接电源线和接地线。电源接线端子最大支持 1.5mm² 电源线。接地线要求阻抗≤ 5Ω，长度≤ 25m，使用内径大小为
3mm 的 OT 端子。
CAUTION/ 注意
• In outdoor installation, a lightning arrester must be installed and the lightning arrester must be grounded.
室外安装时，必须安装避雷器，避雷器必须接地。
• The strong current cables and weak current cables must be separately laid. The distance between the strong current cable and the weak current cable must be greater than or equal to 5 cm. When connecting cables to the device,
do not connect the strong current cable to the weak current interface to avoid device damages.
强电和弱电必须分开布线，两者间的距离不小于 5cm。线缆与设备连接时，禁止将强电接到弱电接口上，以免造成设备损坏。
• If you have to cut off tail cables that cannot be threaded, reserve the labels on the tail cables. Use insulated rubber tapes and waterproof tapes to wrap all tail cables to prevent short circuit and water leakage. Wrap unused cables
with waterproof tapes to prevent water seepage.
如果尾线因无法穿线而必须剪断时，请保留尾线标签。请务必使用绝缘胶带和防水胶带对所有尾线进行绝缘和防水处理，以免造成短路和漏水。对于不用的线头，需要用防水胶带包住，防止渗水。
NOTE/ 说明
Before making an RJ11 plug connector, assemble components of the RJ11 plug connector of the
waterproof connector for network cables in sequence.
在制作水晶头前，请先将网线防水接头的水晶头侧部件按如图所示顺序组装。
Connect the network cable. Mount the rubber ring of the waterproof connector onto the network cable port
and install the remaining components of the waterproof connector in sequence.
连接网线。先将线防水接头部件中的细橡皮圈套在网线接口外，再将剩余部件按如图所示顺序安装。
O-ring for the waterproof connector
网线防水接头密封圈
Power cable
电源线
Ground cable
接地线
5mm
1 2
E Connect Cables/ 连接线缆
Place the wall-mount bracket to the required installation location, use
a marker to mark the screw installation positions and drill holes in the
marked positions.
将壁装支架放置于安装位置，使用记号笔绘制螺钉安装位置，并根据绘制的螺
钉安装位置钻孔。
21 Use a claw hammer to install the expansion bolts into the holes.
使用羊角锤将膨胀螺栓打入钻好的孔内。 3Remove flat washers, spring washers, and nuts from the expansion bolts. Thread the cables through the ceiling-mount bracket. Put the
four expansion bolts through the four screw holes at the bottom of the
ceiling-mount bracket, put the flat washers, spring washers, and nuts
on the expansion bolts, and tighten the nuts.
拧下膨胀螺栓上的平垫、弹垫和螺母。将需要与摄像机尾线对接的线缆穿过吊
装支架。将吊装支架底座上的 4 个螺孔套在相应的膨胀螺栓上，将平垫、弹
垫和螺母套在膨胀螺栓上，拧紧螺母。
NOTE/ 说明
For details about subsequent installation
operations, see steps 4 to 6 in C Indoor
Ceiling-Mount.
后续安装的具体过程请参见“C 室内吊装”中的步
骤4-6。

NOTE/ 说明
Install the Device/ 设备安装 Web Operations/Web 操作
Logging In to the Web Clinet/ 登录 Web 客户端
Use the insulation tape to insulate the connection part of each cable. Then use the waterproof tape and
insulation tape to wrap the cables together into a bundle. Wrap a layer of PVC insulation tape and three layers
of waterproof tape. Then wrap three layers of PVC insulation tape. Ensure that the connection parts of the
cables do not overlap with each other; otherwise, the cable bundle may not pass through the holes because it
is too thick.
先用绝缘胶带对每条线缆对接处做好绝缘防护，然后将所有电缆进行整体绝缘防水处理。绝缘防水处理先缠绕一层 PVC
绝缘胶带，再缠绕三层防水胶带，然后再缠绕三层 PVC 绝缘胶带。对单根线缆做整体缠绕处理时，不同线缆接口处要错开，
避免某处缠绕后过大而影响穿线。
• Stretch the waterproof tape evenly until the tape turns twice as long as before. Then use the stretched
waterproof tape to wrap the cable bundle from the insulation sheath to the protection leather hose (for
example, the PVC conduit).
均匀拉伸防水胶带，使其长度为原长度的 2 倍后再缠绕。防水胶带务必从线缆束绝缘外皮开始缠绕至防护皮管（如
PVC 管）。
• When wrapping the tape, ensure that the upper layer covers more than 50% of the lower layer. Each layer
of tape must be tightened and compacted firmly.
缠绕绝缘胶带和防水胶带时需保证上一层胶带覆盖下一层的 50% 以上，每一层都要拉紧压实。
6
E Connect Cables/ 连接线缆
Connect the alarm cable. It is recommended that twisted pair cables be used as alarm cables. The diameter of
the cable core ranges from 22 AWG to 28 AWG. The impedance of the entire cable is less than or equal to 100
ohms.
连接告警线缆。告警线缆建议使用双绞线，线芯的线径为 22AWG ～ 28AWG，整条线路的阻抗≤ 100Ω。
5
Connect the video cable.
连接视频线缆。
3
Connect the audio cable.
连接音频线。
4
1
2
3
1
2
3
Open Internet Explorer, enter an IPC IP address,IP address can be set automatically via DHCP, or a static IP
address can be set manually (192.168.0.120 by default) and press Enter.
在Internet Explorer地址栏里输入摄像机的IP地址，IP地址默认通过DHCP自动获取，也可以手动进行设置（默认为
192.168.0.120），按“Enter”键。
Enter the UserName and Password. The default UserName is admin and the default Password is HuaWei123.
输入用户名和密码。默认用户名为管理员用户“admin”，默认密码为“HuaWei123”。
Click Login.
单击“登录”。
• If a Dynamic Host Configuration Protocol (DHCP) server is configured for the current network and the
IPC automatically obtains its IP address from the DHCP server, the system will automatically set the IP
address.
当网络配备DHCP（Dynamic Host Configuration Protocol）服务器时，系统将自动配置IP地址。
• Supported browsers (on a 32-bit operating system): Internet Explorer 8, Mozilla Firefox 27, and Google
Chrome 32 or their later versions.
支持的浏览器（32位）：Internet Explorer 8、Mozilla Firefox 27、Google Chrome 32及以上版本。
• To avoid security risks, change the password when logging in to the system as the admin user for the
first time.
首次使用admin用户登录时，请务必修改密码，以免造成安全隐患。
NOTE/ 说明
Log in to the web client as the administrator.
以管理员用户登录 Web 客户端。
Choose Settings > System Configuration > Platform Connection Parameters.
选择“配置 > 系统配置 > 平台对接参数”。
Set the platform connection parameters as planned.
根据规划的数据配置平台对接参数。
For detail about how to set platform connection parameters, see Configuration Guide.
平台对接参数的具体配置方式请参见《配置指南》。
Setting Platform Connection Parameters/ 配置平台对接参数
Setting Network Parameters/ 配置基本网络参数
Log in to the web client as the administrator.
以管理员用户登录 Web 客户端。
Choose Settings > Network Configuration > Network Parameters.
选择“配置 > 网络配置 > 基本网络参数”。
Set the network parameters as planned.
根据规划的数据配置基本网络参数。
For detail about how to set basic network parameters, see Configuration Guide.
基本网络参数的具体配置方式请参见《配置指南》。
1
2
3
The default coding protocol of IPCs is H.265. Verify that the connected surveillance platform supports
H.265. Otherwise, see the Conguration Guide to modify the coding protocol of IPCs.
摄像机出厂默认编码协议为H.265，请务必确认所对接的监控平台是否支持H.265编码协议，否则请参见《配置指
南》修改摄像机编码协议。
NOTE/ 说明

Data Plan/ 数据规划
IP address/IP 地址
Active SDK registration/SDK 主动注册
GB/T 28181
Parameter
参数名
Description
参数解释
Registration
type
注册类型
• Single-server mode: Select this mode when the camera needs to connect to only one video
surveillance platform.
单服务器模式：摄像机仅对接一个监控平台时选择。
• Dual-server mode: Select this mode when the camera needs to connect to two video surveillance
platforms that are deployed in mutual backup mode.
双服务器模式：摄像机对接两个监控平台并且这两个监控平台为互备关系时选择。
Platform IP
平台IP
IP address of the platform server. This parameter is mandatory.
监控平台所在服务器的IP地址。必须设置。
Port number
端口号
Port number of the platform server. This patameter is mandatory.
监控平台所在服务器的端口号。必须设置。
Device ID
设备ID
• Unique camera ID.
设备ID，每台设备的ID唯一。
• The value of this parameter must be the same as the device ID configured on the video surveillance
platform. If they are different, the camera will fail to connect the video surveillance platform.
必须与平台配置的设备ID保持一致，以免造成对接失败。
Parameter
参数名
Description
参数解释
Platform IP
平台IP
IP address of the platform server. This parameter is mandatory.
监控平台所在服务器的IP地址。必须设置。
Port number
端口号
Port number of the platform server. This patameter is mandatory.
监控平台所在服务器的端口号。必须设置。
Device ID
设备ID
Unique ID that the video surveillance platform allocates to the camera. The value of this parameter
must be the same as the first 20 digits in the device ID (the value of Code on the IVS platform)
configured on the video surveillance platform. If they are different, the camera will fail to connect the
video surveillance platform.
监控平台分配给前端设备的唯一标识。必须与平台配置的设备ID（在IVS平台中，该参数名为编码）的前20位保
持一致，以免造成对接失败。
Login name
登录名
User name used to register the camera with the video surveillance platform. The value of this
parameter is in the login name@domain name format. The login name indicates the device ID. The
domain name consists of 10 digits.
用于注册到监控平台。格式为：登录名@域名。登录名为设备ID，域名为自定义10位数字。
Password
密码
Password used to register the camera with the video surveillance platform. The value of this
parameter must be the same as the registration password configured on the video surveillance
platform.
设备注册到平台时的注册密码。必须和监控平台中的注册密码保持一致。
Server code
服务器编码
GB/T 28181 server code. GB/T 28181 server code that consists of 20 self-defined digits.
GB/T 28181服务器编码。自定义输入20位数字。
Parameter
参数名
Description
参数解释
Ways to
obtain IP
获取IP方式
• Automatic: The system automatically configures the IP address, subnet mask, gateway IP address,
and DNS.
自动获取IP地址：系统将自动配置IP地址、子网掩码、网关地址和DNS。
• Manual: You need to manually set the IP address, subnet mask, gateway IP address, and DNS.
使用下面的IP地址：需要用户手动配置IP地址、子网掩码、网关地址和DNS。
IP address
IP地址
• IP addresses starting with 127 are invalid. You must enter an IP address starting with another value
that ranges from 1 to 223.
以127开头的IP地址无效，请输入介于1和223之间的其它数值。
• If the camera is passively registered with the platform using the ONVIF or SDK, only the IP address
needs to be configured.
通过ONVIF和SDK被动注册时，仅需要配置IP地址即可。

Appendix/ 附录
Troubleshooting/ 常见问题处理
Q : After you enter the IPC IP address in the address box and press Enter, the Internet Explorer displays "There
is a problem with this website's security certificate."
A : Click Continue to this web (not recommended) to continue browsing this website. Then, install the root
certificate or upload your own certificate. For details, see Configuration Guide.
问：在 IE 浏览器中输入设备 IP 地址后，网页显示“此网站的安全证书有问题”？
答：单击“继续浏览此网站（不推荐）”，继续访问设备 Web 页面 , 然后安装根证书或上传用户自己的证书文件，具体操
作请参见《配置指南》。
Q : When the root certificate is downloaded, the Internet Explorer displayed "There is a problem with this
website's security certificate", Click "Continue to this website(not recommended)" to access the login page,
the Certificate Error is displayed in the address box.
A : Choose " Settings > System Configuration > Configuration Management " , upload a valid certificate. After
the certificate is uploaded, restart the browser.
问：根证书下载安装完成后，IE 仍提示“此网站的安全证书有问题”，单击“继续浏览此网站（不推荐）”进入登录页面后，
地址栏中出现“证书错误”提示。
答：选择“配置 > 系统配置 > 配置管理”，上传用户自己的合法证书，完成后重新启动浏览器。
Q : What can I do if I forgot the password of the admin user?
A : Use an account with the administrator rights to log in to the web page, choose Setting > System
Configuration > Device Maintenance, and click Restore or hold down the Reset button for at least 3s to
restore the camera to factory defaults.
问：忘记 admin 用户的密码？
答：使用其他拥有管理员权限的帐号登录 Web 页面，选择“配置 > 系统配置 > 设备维护“，单击”恢复默认配置“后恢
复系统默认配置，或者长按 Reset 键 3s 以上恢复系统默认配置。
保 修 卡
尊敬的用户，感谢您使用华为技术有限公司（以下简称华为）的产品，请详细填写保修卡内容，并将下面
的保修卡厂家留存联寄回华为公司，华为公司会登记备案，并保证您的以下权益：
1.您购买的主机可获得12个月的设备免费保修服务（软件介质保修期为3个月）。
2.保修期起始时间计算方式：
从发货之日起九十（90）日或买方第一次申请保修服务之日起孰早开始计算，最晚保修起算时间不超过发货之日起九十（90）日。
3.请注意：
（1）在购买产品时，为保障您的权益，请确认产品从华为的发货日期等保修相关信息。
（2）扩容部件与故障更换件的保修期为华为发货之日起90天，或者跟随主机原有的剩余保修期服务，以两者中较长的时间为准。
（3）免费保修服务仅限于主机（系列主板、电源模块、风扇模块、通信模块、硬盘）和相关辅助部件。
（4）S系列交换机配套的锂电池模块提供保修，但不适用《标准保修说明书》的硬件返修服务响应时间条款。
4.用户可凭保修卡享受保修期内的基本保修服务，服务的详细内容可查看《企业网络产品标准保修说明书》，该保修说明书可在华为企
业业务网站（http://e.huawei.com）查询。
5.中文保修卡仅适用于中国大陆。
华为公司Help Desk热线：400-822-9999（7*24小时）
商业分销产品授权服务中心网站：
http://e.huawei.com ，
依次点击“技术支持>渠道服务>商业分销授权服务中心>授权服务中心服务指南”。
保修卡须经销商盖章方有效
（用户留存）
用户名称：
产品型号：
产品条码：
购买日期： 年 月 日
经销商：
详细地址：
邮编： 电话：
传真： E-mail：
经销单位：（盖章）
用户名称：
详细地址：
邮编： 电 话：
传真： E-mail：
产品条码：
购买日期： 年 月 日
经销商：
经销单位：（盖章）
用户名称：
详细地址：
邮编： 电 话：
传真： E-mail：
产品条码：
经销单位：（盖章）
保修卡（经销商留存）
重要提示：请将此联寄回以下地址
保修卡（厂家留存）
广东省东莞市松山湖科技园新城大道6号
华为南方工厂C区C7-1F 华为维修服务中心
电话：[phone]（5*8h: 8:30-12:00, 13:30-18:00）
邮编：523808
邮件上注明保修卡
設備名稱：半球型網絡攝像機，型號：IPC6325-WD-VR，IPC6325-WD-VF
單元 限制物質及其化學符號
Pb 鉛 Hg 汞 Cd 鎘 Cr6+ 六價鉻 PBB 多溴聯苯 PBDE 多溴二苯醚
結構件○ ○ ○ ○ ○ ○
單板/電路模塊 ○ ○ ○ ○ ○ ○
線纜和線纜組件 ○ ○ ○ ○ ○ ○
紙質配件 ○ ○ ○ ○ ○ ○
備考1：“○”係指該項限用物質之百分比含量未超出百分比含量基準值。
備考2：“-”係指該項限用物質為排除項目。
限制物質含有情況標示聲明書