HUBBARDTON FORGE DESIGN 302517D User manual

Installation Instructions B352
Shard Outdoor Sconces 302515D & 302517D Page 1 of 3
Modern American Blacksmiths | Fine, Hand-Crafted Lighting
Castleton, Vermont USA | HUBBARDTONFORGE.COM 34413
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. Sconces are to be mounted 4 feet above ground. If installing in a non-wood frame application, we
recommend consulting a qualified builder or electrician.
To Mount Fixture to Wall (Figures 1 thru 3)
Component Parts
AFixture Assembly
BMounting Bracket
C#8 Black Screws (4)
DRubber Washer (2)
EGreen Ground Screw
FCupped Washer
GCaulking Lip
HDecorative Assembly
IBlack Screws (2)
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Carefully unpack the fixture from the carton.
2. Using two machine screws (not provided) fasten the
mount bracket (B) to the electric box.
Note: A new electric box comes with screws. When
replacing an existing fixture, retain screws for use with
the new fixture.
3. Remove decorative assembly (H) by removing
the two black screws (I). (Figure 1)
Note: Decorative assembly is shipped installed.
4. Hold the fixture assembly (A) close to the wall
mount bracket and using suitable wire connectors
(not provided), connect fixture wires to supply
wires (white to white and black to black). Ground
the mounting bracket using the green ground
screw (E) and cupped washer (F), from the
mounting kit, to secure a pigtail lead to the
bracket and connect all ground wires (bare
copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted
on securely, and no bare wires are exposed.
(continued)
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
(Figure 1)
(Figure 2)

Installation Instructions B352
Shard Outdoor Sconces 302515D & 302517D Page 2 of 3
Modern American Blacksmiths | Fine, Hand-Crafted Lighting
Castleton, Vermont USA | HUBBARDTONFORGE.COM 34413
5. Apply a generous bead of a suitable caulking
material (not provided) to caulking lip (G) on
the fixture. Caulk should be applied around the
entire perimeter of the back (Figure 3)
6. Carefully tuck all wires behind the fixture assembly
(A) and inside the mounting bracket (B). Place the
fixture assembly (A) firmly onto mounting bracket (B)
and fasten with two #8 black screws (C) and rubber
washers (D) on top. (Figure 2)
7. Install the two remaining black screws (C) in bottom
of fixture attaching to wall mounting bracket (B).
(Figure 2)
To Install Glass (Figure 4)
Component Parts
HDecorative Assembly
JGlass
KSet Screw
1. Carefully slide glass (J) into decorative assembly
(H). The side of the glass (J) with different colored
pieces should be facing the set screw.
Note: Set screw (K) might need to be backed
out before glass (J) can be dropped it. It is not
necessary to completely remove set screw (K).
2. Using hex wrench (provided), tighten set screw
(K) until snug against glass (J). Be careful not to
overtighten.
(continued
(Figure 3)
(Figure 4)

Installation Instructions B352
Shard Outdoor Sconces 302515D & 302517D Page 3 of 3
Modern American Blacksmiths | Fine, Hand-Crafted Lighting
Castleton, Vermont USA | HUBBARDTONFORGE.COM 34413
To Complete Installation (Figure 5)
Component Parts
AFixture Assembly
HDecorative Assembly
IBlack Screws (2)
JGlass
1. Hold decorative assembly (H) with glass (J)
installed up to fixture assembly (A). Install
two black screws (I) to secure decorative
assembly (H).
2. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(Figure 5)