HUDSON STEEL ES-701 User manual

BIKE ES-701
MANUAL

ES-701 INSTRUCTIONS FOR USE
1)
The model ES-701 is designed to be used as a group cycle in fitness studios and health clubs.
It has a fixed wheel driven flywheel and should only be used under professional supervision.
2)
Installation – it is important that the ES-701 is correctly assembled
and we recommend that installation and assembly be carried out by suitably qualified personnel.
3) Handlebar and seat adjustment. It is important that the handlebar and seat are
set at the correct height for your body. Ask your instructor for assistance.
Adjusting the handlebar height - Make sure it is securely tightened and that there
is no lateral or vertical movement of the handlebar. Undo the Quick Release knob
which is located in front of head tube. Slide the handlebar/stem up or down to the
required height and then retighten.
The handlebar/stem position can also be adjusted forwards or backwards. Undo
the Quick Release lever located on below the slider. Slide the handlebar/stem
assembly forwards or backwards until you reach the required position. Then
securely re-tighten the Quick Release lever.
Adjusting the seat height – refer to above mention.
NOTE: there is a safety line engraved on the seat post. On no account
should the seat post ever be raised above this line.
4) Pedals and toestraps – your feet should be securely positioned in the toe clips
during the exercise. Put your foot as far forward as you can into the toe-clip and then pull the strap tight.
5)
Resistance system- ES-701 bike is with durable belt direct drive transmission system,
to adjust the exercising resistance on the completed spinning bike, undo the simply loosen
or tighten using adjustment knob. Press down the brake lever for stopping the wheel.
6)
The ES-701 should operate on a level surface with no lateral movement.
There are height adjuster pads located on either side underneath the rear foot.
Turn these pads clockwise or anti-clockwise until the bike is totally stable on the ground.
7)
Maintenance – like any other mechanical cycling device, the ES-701 should be
regularly maintained. Ask your supplier for a detailed maintenance programme.

ES-701 Assembly Diagrams

ES-701 ASSEMBLY
Step 1 (foot)
Attach the front foot (7) to the frame using the bolt (3A) and washer (6).
Step 2 (foot)
Attach the rear foot (2) to the frame using the bolt (3A) and washer (6).
Step 3. (pedals)
attach the pedals (70R/70L) into the crank arms (62R/62L), each pedal
is marked with the letter R(right) or R(right) to denote the side of the bike
they are on. NOTE: the right hand crank is on the same side as the
chain cover (71). Be careful to align the threads correctly to avoid any damage.
A little grease on the thread should help the pedals to screw in easily
and correctly, tighten using a 15mm spanner, both pedals threads should
tighten towards the front of the bike.
STEP 2

Step 4. 5. (handlebar & stem)
Open screw(14) from handlebar top slider then assemble slider's locking piece (78) onto
bottom slider , attach handlebar (11) onto handle bar stem (20)then sliding forward until
coming to a stop , assemble lock lever (12) then screw bolt (14) into top slider and tighten it ,
Insert slider's end cap (74) into top slider .
slide handlebar (11) until reach your required position then use lock lever(12) for tightening.
using lock lever (18) for stem height adjustment . NOTE: Do not arise above safety line.
Step 6. 7. (saddle & seat post)
Insert seat post (15) into frame's seat tube, assembly saddle (17) on
saddle top slider (16). Adjust slider using lock lever (12) for forwards or backwards.
and then tighten until reach the proper position. Using lock lever (18)
adjust seat post (15) and tighten in proper position.
NOTE: Do not arise above safety line.
STEP 7
STEP 5
20
18
STEP 4
15
18
STEP 6

ES-701 Explode Diagram

parts no. description q'ty parts no. description q'ty
1Main Frame 1
11
141 Brake pad 1
11
1
2Rear Ground Tube 1
11
142 Brake pad fixed screw 1
11
1
3Rear Ground Tube Fixed 2
22
243 Bush 1
11
1
3A Front Ground Tube fixed 2
22
244 Nut 1
11
1
4Handlebar & Slider fix plate 1
11
145 Brake Arm 1
11
1
5bolts 4
44
446 Spacer 1
11
1
6Washer 4
44
447 Lift spring 1
11
1
7Front Ground Tube 1
11
148 Washer 1
11
1
8Fly Wheels Fixed Nut 2
22
249 Stud B 1
11
1
9Washer 2
22
250 Brake arms fixed Bolt 1
11
1
10 bolts 4
44
451 Washer 2
22
2
11 Handle Bar 1
11
152 Stud A 1
11
1
12 Lock lever for HB and seat 2
22
253 PU Moving Wheel 2
22
2
13 Handlebar Slider 1
11
154 Grounds End Cap 4
44
4
14 Slider's safety stoper 4
44
455 Bearing 608ZZ 4
44
4
15 Seat Post 1
11
156 Nut 2
22
2
16 Saddle slider 1
11
157 Bolt 2
22
2
17 Saddle 1
11
158 Axle Lock Nut 1
11
1
18 Lock Lever For Stem & Post 2
22
259 Dusty Cover 1
11
1
19 Set Screw 260 Spacer 1
11
1
20 Stem 1
11
161 B.B Axle 1
11
1
21 Locking Piece 2
22
262L Left Crank 1
11
1
22 Pop cover 2
22
262R Right Crank 1
11
1
23F/23 Plastic Sleeve for H/T and 2
22
263 Flange Nut 2
22
2
24 Left Cover 1
11
164 Plastic cap 2
22
2
25 Nut 1
11
165 Driving Pulley 1
11
1
26 Nut 1
11
166 Spring washer 4
44
4
27 Adjust Knob 1
11
167 Belt 1
11
1
28 Floating Piece 1
11
168 Inner Cover 1
11
1
29 Nut 2
22
269 Screw 13
1313
13
30 Round steel plate 2
22
270 R/L LU-214 alloy body w/ toe clip& strap. 1
11
1
31 Spring 1
11
171 Outer Chain Cover 1
11
1
32 Integrated Plastic Bottle 1
11
172 Ground Tube's Adjusting Pad 4
44
4
33 Axles Adjusting Bolts 2
22
273 Washer 2
22
2
34 Fly Wheels Axle 1
11
174 HB(F) & Saddle Slider's (R) End Cap 2
22
2
35 Spacer 1
11
175 HB(R) & Saddle Slider's (F) End Cap 2
22
2
36 B.B & Fly Wheel Axle's 4
44
476 Stem(F) & Post Slider's (R) End Cap 2
22
2
37 Floating piece set screw 1
11
177 Stem(R) & Post Slider's (F) End Cap 2
22
2
38 Nut 3
33
378 Stem/Post Slider's Locking Piece 2
22
2
39 Fly Wheel 1
11
179 Front slider's sliding protector 2
22
2
ES-701 Parts List