Huffy 89224 User manual

1P/N 211678A 06/03
Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Company
BASKETBALL
CENTER
BASKETBALL
CENTER
IMPORTANT!
To ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample
and Display Technician at 1-800-558-5234.
REQUIRED TOOLS AND
MATERIALS:
• Wrenches: (Two each) 7/16”, 1/2”, 9/16”,
and 3/4” or Pliers
• Step Ladder, 8 ft. (2.4 m)
Model 89224
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.
• During assembly, if using a ladder use extreme caution. Two
people are recommended for this operation.
• If technical assistance is required, contact Huffy Sports’ Sample
and Display Technician.
• Serious injury could occur if teeth/face come in contact with
backboard, net or rim.
• Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4”
(10 cm) Square poles only.
• All instructions and warnings MUST accompany any display item
that is sold.
Most injuries are caused by misuse and/or not following
instructions.
Use caution when installing this unit.
Internet Address: http://www.huffysports.com

P/N 211678A 06/03 2
PARTS LIST
Item Qty. Part No. Description
1 1 901097 Extension Arm
21 207103 Pole Cap for 3.5” Pole Section
3 2 203100 Nut, Hex Flange 5/16-18*
4 2 201611 Bolt, Hex Flange, 5/16-18 x 3”
5 4 203218 Washer, Flat, 5/16*
6 2 200516 Bolt Cover, Vinyl*
7 1 908812 3.5” Pole Section
8 4 202460 Saddle Clamp
9 4 201763 Bolt, Carriage, 3/8-16 x6.5”
10 4 203063 Locknut, 3/8 -16
11 1 204290 Spider Net

3P/N 211678A 06/03
CURRENT
INSTALLATION
DIAGRAM
FRONT
The side with pegboard on
the top and bottom.
44” Fan
Backboard
44” Fan
(Remains in
center location)
48” Fan Backboard
44” Steel Framed Acrylic
EXACTAHEIGHT POLE
ASSEMBLY:
REMOVE & DISCARD
OR IT MAY BE LOCATED
IN A DIFFERENT
CORNER.

P/N 211678A 06/03 4
TWO PEOPLE ARE
NECESSARY TO MOUNT THE
ELEVATOR ASSEMBLY TO
THE POLE. ONE PERSON
SHOULD NOT ATTEMPT TO
DO THIS ALONE.
WARNING
TOP
VIEW
FRONT
3-1/2” Rnd. Pole
3-1/2” Rnd. Pole X 30” Pole
Install pole mounting hardware and pole for each
assembly.
3-1/2” Rnd. Pole
3-1/2” Rnd. Pole
Upper Support
Railing
10
8
9
4
3-1/2” Rnd. Pole

5P/N 211678A 06/03
Assemble display products per diagram below. TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE. NOT
FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY INJURY.
WARNING
48” Fan
Backboard
44” Fan
48” Rectangle Steel
Framed Acrylic
44” Fan
INSTALLATION DIAGRAM
44” Rectangle
Steel Framed
Acrylic
FRONT

P/N 211678A 06/03 6
Mount extension arm and
rim to backboard and
finger tighten as shown.
NOTE: For spring
loaded rim assembly,
refer to instructions
included with rim
hardware.
Secure hardware to extension
arm as shown and tighten
completely. Install pole cap (2).
Refer To Combo For
Goal Assembly
Instructions
1.
2.
6
45
5
2
7
3
1