Huffy Single Electronic Basketball System User manual

112/05 ID# M611804
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 7921
Internet Address: http://www.huffysports.com
REQUIRED
MATERIALS:
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
WARNING!
•Two (2)
Capable
Adults
•Wood Board
(scrap)
•Sawhorse or
Support Table
SAND
SAND
(360 lb.)
(360 lb.)
(163 kg)
(163 kg)
Write Model Number
From Box Here:
•Garden Hose or Sand
© COPYRIGHT 2005 by SPALDING
Portable System
Owners Manual
• (2 each) Wrenches and/or
Socket Wrenches and
Sockets.
1/2"7/16" 9/16"
AND/OR
1/2"7/16" 9/16"

2
ID# M611804 12/05
36
LABEL AS APPROVED BY HUFFY SPORTS ENGINEERING
FOR OUTDOOR APPLICATION
2-5/8" Wide x 6-5/8" Long
561180 01/06
1
3
2
MOVING SYSTEM
HEIGHT
ADJUSTMENT
A
B
B
A
1. While holding pole, rotate basketball sytem
forward until wheels engage with ground.
2. Move basketball system to desired location.
3. Carefully rotate basketball system upright.
4. Check system for stability.
Owner must ensure that all players know and follow
these rules for safe operation of the system.
WARNING
• DO NOT HANG on the rim or any part of the
system including backboard, support braces or
net.
• During play, especially when performing dunk
type activities, keep player's face away from
the backboard, rim and net. Serious injury
could occur if teeth/face come in contact with
backboard, rim or net.
• Do not slide, climb, shake or play on base
and/or pole.
• After assembly is complete, fill system
completely with water or sand. Never leave
system in an upright position without filling
base with weight, as system may tip over
causing injuries.
• When adjusting height or moving system, keep
hands and fingers away from moving parts.
• Do not allow children to move or adjust system.
• During play, do not wear jewelry (rings,
watches, necklaces, etc.). Objects may
entangle in net.
• Surface beneath the base must be smooth and
free of gravel or other sharp objects. Punctures
cause leakage and could cause system to tip
over.
• Keep organic material away from pole base.
Grass, litter, etc. could cause corrosion and/or
deterioration.
• Check pole system for signs of corrosion (rust,
pitting, chipping) and repaint with exterior
enamel paint. If rust has penetrated through
the steel anywhere, replace pole immediately.
• Check system before each use for proper
ballast, loose hardware, excessive wear and
signs of corrosion and repair before use.
• Check system before each use for instability.
• Do not use system during windy and/or severe
weather conditions; system may tip over. Place
system in the storage position and/or in an
area protected from the wind and free from
personal property and/or overhead wires.
• Never play on damaged equipment.
• When moving system, use caution to keep
mechanism from shifting.
• Keep pole top covered with cap at all times.
• Do not allow water in tank to freeze. During
sub-freezing weather add 2 gallons of non-toxic
antifreeze, sand or empty tank completely and
store. (Do not use salt.)
• While moving system, do not allow anyone to
stand or sit on base or have added ballasting
on base.
• Do not leave system unsupervised or play on
system when wheels are engaged for moving.
• Use Caution when moving system across
uneven surfaces. System may tip over.
• Use extreme caution if placing system on
sloped surface. System may tip over more
easily.
• See instruction manual for proper installation
and maintenance.
Read and understand warnings listed
below before using this product.
Failure to follow these warnings may
result in serious injury and/or property
damage.
MUNSELL NOTATION
Hue Value Chroma
5.0 YR 6.0/15
Equiv. CIE Data
(Y%) x y
30.05 0.5510 0.4214
Approx. PMS Color
13 parts yellow
3 parts Warm Red
1/4 part Black
Warning Area = Orange
Size = 2-5/8" x 10- 11/16
Corner Radius = 3/8"
Die Cut Label
3.25 Mil Vinyl
All Temp. Permanent Adhesive
1 Mil. Polypropolyne Overlaminate
Illustrator 8.0 = EPS
Backing + 1/16 Circumference
Rolls of 500
ID#: 561000 01/06
In the U.S.: 1-888-713-5488 In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339
In the U.S.: 1-800-334-9111
In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339
10-11/16" High
2-5/8" Wide
PMS 021 for Warning

312/05 ID# M611804
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
NOTICE TO ASSEMBLERS
ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted
with sand or water according to instructions. Failure to follow instructions could result in
SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
• If using a ladder during assembly, use extreme caution.
• Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to separate during play and/or during transport of the system.
• Climate, corrosion or misuse could result in system failure.
• If technical assistance is required, contact Customr Service.
• Minimum operational height is 6'-6" (1.98m) to the bottom of backboard.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
WARRANTY CARD:
Please remember to complete your product registration form either
on-line at:
www.huffysports.com/customer_support/product_registration
or mail-in the enclosed postcard.

4
ID# M611804 12/05
Get to know the basic parts of your basketball system...
3121
22
10
11
7
4
32
26
30
20
8
9
2
18
16
1
3
14
23
12
13
19
15
33
17
25
24
29
17
23
15
17
16
17
20
17
33
33176
27
28
5

512/05 ID# M611804
PARTS LIST
ITEM NO. PART NUMBER TITLELINE1 QTY
206646 Base (Black)
2
1
FR908314 Bottom Pole
3 600029 Adapter, Pole
4 FR70000 Middle Pole
5 FR90831 Top Pole
6 908316
Backboard Mounting Bracket
7 202528 Pin
8 900255
Strut - 26.25 x .75 RH
9 900454 Strut, 26.25 x .75 LH
10
11
600030 Bushing, Pole
600031 Bushing (Internal)
12 200628 Wheel Axle
13 226401
Wheel - 4" 2
1
1
1
1
1
1
1
1
1
1
1
1
1
14 201342 Wheel Bracket
15 201651
Spacer, 505ID X 1.13OD X .25" LONG 2
16 201625
Bolt, 5/16-18 x 3.60
2
17 203218 Washer, 5/16 10
18 205372 Eye Bolt, 3/8-16 x 4.5
19 203063 Locknut, 3/8
20 203223
Bolt,Carriage, 5/16-18 X 1"
2
21 203084
Bolt,Carriage, 5/16-18 X 1.75"
22 206263
Bolt, Carriage, 5/16-18 X 3.25"
2
23 203100
Nut, 5/16-18
2
24 202319
Goal Plate
25 201344 Knob, Plastic, 3-sided
26 205389 Lock-Nut, Nylon Insert,1/4-20 3
27 600032 Pole Cap
28 203617
Tank Cap
29 Rim
30 205373
Bolt, Hex Head,1/4-20 X 3.25
3
31
Backboard
32 700009 Handle Assembly
33 203099
Lock-Nut, Nylon Insert, 5/16-18
4
34
Net
35 205397
Decal, Height Indication
1
1
1
1
1
1
1
1
1
1
1
1
36 561180 / FR561180
Label, Height Adjustment and Moving
1
37
Allen Wrench
1
Légende No. de réf. Description Qté
206646 Socle (noir)
2
1
Section de poteau inférieure
3 600029 adapteur, de poteau
4Section de poteau centrale
5Section de poteau supérieure
6 908316
Support de panneau
7 202528 Goupille
8 900255
Contrefiche du réservoir argent - 26.25 x .75, droite
9 900454 Contrefiche du réservoir argent - 26.25 x .75, gauche
10
11
600030 Douille, de poteau
600031 Douille (interne)
12 200628 Axe des roues
13 226401
Roue - 4" 2
1
1
1
1
1
1
1
1
1
1
1
1
1
14 201342 Support de roues
15 201651
Entretoise, 505ID X 1.13OD X .25" (long.) 2
16 201625
Boulon, 5/16-18 x 3.60 5/16-18 x 3.60
2
17 203218 Rondelle, 5/16 10
18 205372 Boulon à œil, 3/8-16 x 11,43 cm (long.)
19 203063 Contre-écrou, 3/8
20 203223
Boulon ordinaire, 5/16-18 X 1"
2
21 203084
Boulon ordinaire, 5/16-18 X 1.75"
22 206263
Boulon ordinaire, 5/16-18 X 3.25" long
2
23 203100
Écrou, 5/16-18
2
24 202319
Plaque, but
25 201344 Bouton en plastique, 3 côtés
26 205389 Contre-écrou, insert en nylon,1/4-20 3
27 600032 Capuchon de poteau
28 203617
Bouchon du réservoir
29 Cerceau
30 205373
Boulon, six pans,1/4-20 X 3.25
3
31
Paneau
32 700009 Poignée
33 203099
Contre-écrou, insert en nylon, 5/16-18
4
34
Filet
35 205397
Autocollant, indication de hauteur
1
1
1
1
1
1
1
1
1
1
1
1
36
Étiquette, réglage de hauteur et déplacement
1
37
Clé Allen
1
Nr. Teile-Nr. Beschreibung Anz.
206646 Sockel
2
1
Unteres Stangenteil
3 600029 Adapter, Stangenteil
4Mittleres Stangenteil
5Oberes Stangenteil
6 908316
Korbwand-Montagehalterung
7 202528 Stift
8 900255
Tankstrebe, 26.25 x .75, rechter
9 900454 Tankstrebe, 26.25 x .75, linker
10
11
600030 Buchse, Stangenteil
600031 Buchse (intern)
12 200628 Radachse
13 226401
Rad- 4" 2
1
1
1
1
1
1
1
1
1
1
1
1
1
14 201342 Radhalterung
15 201651
Abstandsstück, 505ID X 1.13OD X .25" Länge 2
16 201625
Schlossschraube, 5/16-18 x 3.60
2
17 203218 Unterlegscheibe, 5/16 10
18 205372 Einschrauböse, 3/8-16 x 4.5
19 203063 Gegenmutter, 3/8
20 203223
Schlossschraube, 5/16-18 X 1"
2
21 203084
Schlossschraube, 5/16-18 X 1.75"
22 206263
Schlossschraube, 5/16-18 X 3.25"
2
23 203100
Sechskant-Flanschmutter, 5/16-18
2
24 202319
Torplatte
25 201344 Plastikknopf, 3-seitig
26 205389 Nylon-Einschraubgegenmutter,1/4-20 3
27 600032 Stangenkappe
28 203617
Tankdeckel
29 Korbrand
30 205373
Sechskantschraube,1/4-20 X 3.25
3
31
Korbwand
32 700009 Griffbaugruppe
33 203099
Nylon-Einschraubgegenmutter, 5/16-18
4
34
Netz
35 205397
Höhenanzeigeaufkleber
1
1
1
1
1
1
1
1
1
1
1
1
36
Höheneinstell- und Transportaufkleber
1
37
Inbusschlüssel
1
Artículo. Pieza N.º Descripción Cant.
206646 Base (Black)
2
1
Sección inferior del poste
3 600029 Adaptador, poste
4Sección media del poste
5Sección superior del poste
6 908316
Soporte del borde
7 202528 perno
8 900255
Puntal del tanque - 26.25 x .75 derecha
9 900454 Puntal del tanque - 26.25 x .75, izquierda
10
11
600030 Buje, poste
600031 Buje, (internol)
12 200628 Eje de la rueda
13 226401
Rueda - 4" 2
1
1
1
1
1
1
1
1
1
1
1
1
1
14 201342 Soporte de la rueda
15 201651
Espaciador, 505ID X 1.13OD X .25" longitud 2
16 201625
Perno, 5/16-18 x 3.60
2
17 203218 Arandela, 5/16 10
18 205372 Perno de anilla, 3/8-16 x 4.5
19 203063 Contratuerca, 3/8
20 203223
Perno cabeza de carro, 5/16-18 X 1"
2
21 203084
Perno cabeza de carro, 5/16-18 X 1.75"
22 206263
Perno cabeza de carro, 5/16-18 X 3.25"
2
23 203100
Tuerca, 5/16-18
2
24 202319
Placa, aro
25 201344 Perilla, plástico, 3 lados
26 205389 Contratuerca, inserto de nilón,1/4-20 3
27 600032 Tapa del poste
28 203617
Tapa del tanque
29 Borde
30 205373
Perno, cabeza hexagonal,1/4-20 X 3.25
3
31
Respaldo
32 700009 Conjunto de la manija
33 203099 Contratuerca, inserto de nilón,
, 5/16-18
4
34
Red
35 205397
Calcomanía, indicación de la altura
1
1
1
1
1
1
1
1
1
1
1
1
36
Etiqueta, ajuste de la altura y de movimiento
1
37
Llave Allen
1
31 21
5
22
10
11
7
4
32
26
30
20
8
9
2
18
16
1
3
14
23
12
13
19
15
33
17
25
24
29
17
23
15
17
16
17
20
17
33
3317 6
27
28
561180 / FR561180
561180 / FR561180 561180 / FR561180
FR908314
FR70000
FR90831
FR908314
FR70000
FR90831
FR908314
FR70000
FR90831

6
ID# M611804 12/05
PARTS IDENTIFIER- Actual Size
203041
NUT, HEX FLANGE, 3/8-16
#23 (2)
#15 (2)
#29 (1)
#14 (1)
#10 (1) #11 (1)
#25 (1) #28 (1)
#12 (1)
#9 (1)#8 (1)#7 (1)
#1 (1)
#13 (2)
#34 (1)
#24 (1)
#31 (1)
#6 (1)
#17 (10)
#18 (1)
#26 (3)
#27 (1)
#16 (2)
#30 (3)
#19 (1)
PARTS IDENTIFIER- Not Actual Size
#32 (1)
#22 (2)
#20 (2)
#21 (1)
#36 (1)
203099Hex Locknut (Nylon Insert) 5/16-18
#33 (4)

712/05 ID# M611804
1.
Correctly identify each pole section. Poles have an
identification sticker that will be used as a reference
point in the next step.
4
5
2
TOP
MIDDLE
BOTTOM
2. 14
12
13
15
THE SPACER (15) WILL
FIT LOOSELY UNTIL
SECURED INTO THE
CAVITY OF THE BASE.
IMPORTANT!:
Install wheel axle (12) through
wheel bracket (14) and install
wheels (13) onto wheel axle (12)
with spacers (15) as shown.

8
ID# M611804 12/05
Attach wheel carriage assembly and pole (5)
to base (1) as shown.
3. 4.
Secure eyebolt (18) inside bottom pole
(2) using washer (17) and nut (33) as
shown. Place pole adapter (3) onto
bottom pole (2). Allow eyebolt (18) to
come through hole in pole adapter (3).
3
2
18
19
2
1
18
16
18
17
33
17
2

912/05 ID# M611804
5.
17
20
23
Secure tank struts (8 & 9) to pole as shown.
Rotate struts down and bend struts outward to line up with holes on base as shown. Secure
free ends of tank struts to tank with carriage bolt (20), washer (17), and nut (23) as shown.
Repeat for other side.
16
9
1
33
17 17
8
17
20
17
23
17
TIGHTEN BOLT (16) IN
LOCK NUT (33) UNTIL
FLUSH (EVEN) WITH LOCK
NUT’S OUTER EDGE.
WARNING!
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING
COULD RESULT IN SERIOUS
INJURY AND/OR PROPERTY
DAMAGE.
WARNING!

10
ID# M611804 12/05
6.
C
26
5
2
A). Insert pole cap (27) into top of top pole assembly (5).
B). Slide top pole assembly (5) into bottom pole assembly as shown. NOTE ORIENTATION.
C). Secure top pole assembly (5) to bottom pole using bolts (30) and nuts (26) as shown.
27
5
AB
5
2#36
30