Humminbird 700 series User manual

700 Series™ In-Dash Mounting Kit
4
531462-1_C
Returning Your Unit for Service
Before sending your unit in for repair, please contact the factory, either by
phone or by email, to obtain a Repair Authorization Number for your unit.
NOTE: Please do not return your Humminbird® to the store for service.
Please have your product model name and serial number available
before calling the factory. If you contact the factory by e-mail, please
include your product model name and serial number in the e-mail, and
use Request for Repair Authorization Number for your e-mail subject
header. You should include your Repair Authorization Number in all
subsequent communications about your unit.
For IN-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird®
Customer Resource Center.
• Tag product with your name, street address, phone number and
your assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date of
purchase).
• Return product freight prepaid to Humminbird®, using an insured
carrier with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird®
Customer Resource Center.
• Include payment in the form of credit card number and expiration
date, money order or personal check. Please do not send cash.
• Tag product with your name, street address, phone number and
your assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird®, using an insured
carrier with delivery confirmation.
Contact Humminbird®
Contact the Humminbird® Customer Resource Center
in any of the following ways:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
[email protected]
For direct shipping, our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of
Johnson Outdoors Inc. to be a responsible corporate citizen, operating
in compliance with known and applicable environmental regulations,
and a good neighbor in the communities where we make or sell our
products.
WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and
Electronic Equipment Directive (WEEE)” impacts most distributors,
sellers, and manufacturers of consumer electronics in the European
Union. The WEEE Directive requires the producer of consumer
electronics to take responsibility for the management of waste from
their products to achieve environmentally responsible disposal during
the product life cycle.
WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed and
intended as fixed or temporary installation in transportation vehicles
such as automobiles, aircraft, and boats. In some European Union
member states, these vehicles are considered outside of the scope of
the Directive, and EEE for those applications can be considered
excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the
product must not be disposed of with other household refuse. It
must be disposed of and collected for recycling and recovery of
waste EEE. Johnson Outdoors Inc. will mark all EEE products in
accordance with the WEEE Directive. It is our goal to comply in the
collection, treatment, recovery, and environmentally sound disposal of
those products; however, these requirement do vary within European
Union member states. For more information about where you should
dispose of your waste equipment for recycling and recovery and/or your
European Union member state requirements, please contact your dealer
or distributor from which your product was purchased.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
700 Series™ In-Dash Mounting Kit
1
531462-1_C
Thank You
Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation
by designing and manufacturing top-quality, thoroughly reliable marine equipment. Genuine Humminbird®
accessories offer the opportunity to upgrade and expand the capabilities of your Humminbird® product.
Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment. In the
unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy - free
of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For
complete details, see the Warranty section included in this manual.
Contact our Customer Resource Center at either 1-800-633-1468 or visit our website at www.humminbird.com.
Installation Overview
Following are instructions for the recessed installation of the 700 SeriesTM control head into a hole in the
dash. Before you start installing the 700 SeriesTM control head, we encourage you to read these instructions
carefully in order to get the full benefit from your Humminbird® accessory.
If you find that any items are missing from your installation kit, call our Customer Resource Center at
1-800-633-1468 or visit our website at www.humminbird.com.
In addition to the hardware supplied with your In-Dash Mounting Kit, you will need a reciprocating saw for
cutting the dash material and masking tape to hold the mounting template in place.
In-Dash Mounting
To in-dash mount the 700 SeriesTM control head, start by placing the components on the surfaces where you
intend to install them before installation. Make sure that the surfaces you have chosen provide adequate
protection from wave shock and that all cables can reach the control head.
NOTE: If a cable is too short for your application, extension cables are available. Call Humminbird®
Customer Support at 1-800-633-1468 for more information.
1. Locate a suitable, flat area of the dash to mount the control head. The control head requires a depth of
at least 3 inches (76 mm).
2. Tape the paper In-Dash Mounting template to the desired in-dash mounting location.
3. At a location inside the dotted line on the template, drill a hole large enough to insert the blade of the
reciprocating saw. Carefully begin cutting toward the dotted line, then follow the dotted line around the
template. Remove the template when finished.
4. Insert and tighten the two threaded rods into the two threaded inserts located on the back side of the
control head. Peel off the adhesive-backed foam pads and place them on the back of the control head;
make sure you notice the difference between the longer top/bottom and shorter side pads.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
Applying the Foam Pads

700 Series™ In-Dash Mounting Kit
3
531462-1_C
1-Year Limited Warranty
We warrant the original retail purchaser that products made by
Humminbird® have been manufactured free from defects in materials
and workmanship. This warranty is effective for one year from the date
of original retail purchase. Humminbird® products found to be defective
and covered by this warranty will be replaced or repaired free of charge
at Humminbird® option and returned to the customer freight prepaid.
Humminbird® sole responsibility under this warranty is limited to the
repair or replacement of a product that has been deemed defective by
Humminbird®. Humminbird® is not responsible for charges connected
with the removal of such product or reinstallation of replaced or
repaired parts.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended in the
product installation and operation instructions;
• Damaged or has failed because of an accident or abnormal
operation;
• Repaired or modified by entities other than Humminbird®.
Please retain your original receipt as a proof of the purchase date. This
will be required for in-warranty service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD® AND
WILL BE THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY
APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE
HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF
ORIGINAL PURCHASE. IN NO EVENT WILL HUMMINBIRD® BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS.
Some states do not allow limitations on an implied warranty, or the
exclusion of incidental or consequential damages, so the above
exclusions may not apply to you. You may also have other rights, which
vary from state to state.
Humminbird® Service Policy
Even though you'll probably never need to take advantage of our
incredible service policy, it's good to know that we back our products
this confidently. We do it because you deserve the best. We will make
every effort to repair your unit within three business days from the
receipt of your unit at our factory. This does not include shipping time to
and from our factory. Units received on Friday are typically shipped by
the following Wednesday, units received Monday are typically shipped
by Thursday, etc.
All repair work is performed by factory-trained technicians to meet
exacting factory specifications. Factory-serviced units go through the
same rigorous testing and quality control inspections as new
production units.
After the original warranty period, a standard flat rate service charge
will be assessed for each repair (physical damage and missing parts are
not included). Any repairs made after the original warranty will be
warranted for an additional 90 days after service has been performed
by our factory technicians. You can contact our Customer Resource
Center or visit our website to verify the flat rate repair fee for your
product (visit the Product Support section):
http://www.humminbird.com
We reserve the right to deem any product unserviceable when
replacement parts are no longer available or impossible to obtain. This
Service Policy is valid in the United States only. This applies only to
Humminbird® products returned to our factory in Eufaula, Alabama.
This Service Policy is subject to change without notice.
DOMESTIC (USA) CUSTOMERS:
PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE
For all technical issues please call 1-800-633-1468
Or visit www.humminbird.com, click SUPPORT
Please reference product serial number and
model number when contacting Humminbird®.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
700 Series™ In-Dash Mounting Kit
2
531462-1_C
5. Insert the control head through the mounting hole from the front side of the dash. From the back side
of the dash, align the two threaded rods on the rear of the housing with the two holes on the in-dash
mounting bracket. Place a lock washer onto each threaded rod, then secure bracket by placing a hex nut
onto each threaded rod and tighten fully.
6. Insert cable connectors into the proper recesses on the cable collector. The cable connectors are keyed
to prevent reverse installation, so be careful not to force the connectors into the wrong slots.
7. While holding cables in place in the cable collector, place retainer over cables and screw in place using
the two Phillips screws provided.
8. Place the cable collector assembly into the back of the control head. Cable connectors and cable sockets
are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong
sockets.
NOTE: It is very important that the cable collector is used and secured in place in the In-Dash installation.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
700 Series™ Indash Mounting Assembly
Assembling the Cable Connector