To set a call tone
Your radio can transmit different call tones to other radios in your group so you can
alert them that you want to talk. Your radio has 10 call tones from which choose.
1.Press button until icon appears.The current call tone setting will flash.
2.Press to change and hear the call tone.
3.Press PTT to save .
Voice Operated Transmission (Vox)
Transmisson is initiated by speaking into the microphone of the radio instead of the
pushing the PTT button.
Scanning Channels
Eatures your radio to scan for active channels .when activity is detected, your radio
lands (stays) on that channel for 5 seconds. To transmit on that channel ends, your
radio continues scannig to other channels.
To turn the channel scan ON:
1.Press and hold to enter Scan mode.
2.press orPTT to turn off Scan mode.
Note:
During scanning , press the key to change the direction of the scan.
Safety and General Information
1.If you carry any kind of personal medical device, consult a doctor before use.
2.To avoid the risk of burns, do not use the device if the aerial is damaged in any way.
3.Never use the device in close proximity to a radio to avoid interference.
4.Position the transmitter and antenna at least 5 cm from your mouth.
5.The device cannot be used to contact the emergency services.
Interference Eliminator Code
Interference Eliminator Codes help minimize interference by providing you with a
choice of code combinations. To set the code for a channel:
1. Press until the code starts to flash.
2. Press to select the code 0-99 0R 99-0.
3. Press PTT to save the code setting.
You can set a different code for each channel using this procedure.
Note: You must set the Interference Eliminator Codes to 0 on an FRS radio that uses
Interference Eliminator Codes to communicate with other FRS radios that do not have
Interference Eliminator Codes.
TOT (TIME OUT Timer )
In order to prevent the use of the channel and save power, walkie-talkie has emission
limit function, then the launch time is less than 180 seconds.
When reached the default time , the radio stops launching with "beep" tone.
Locking the Keypad
To avoid accidentally changing your radio settings, press for 3 seconds or until
displays and there is a "beep" tone. You can turn the radio on and off, you can't adjust
the volume, menu, and monitor channels. All other functions are locked.
To unlock the radio, press for 3 seconds or until is no longer displayed. And
there is a “beep" tone.
Note: When locking , only the PTT and are valid.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group so you can
alert them that you want to talk.
5
76
4
Special Features
462.55000-467.71250MHz
446.00625-446.09375MHz
To set a call tone
Your radio can transmit different call tones to other radios in your group so you can
alert them that you want to talk. Your radio has 10 call tones from which choose.
1.Press button until icon appears.The current call tone setting will flash.
2.Press to change and hear the call tone.
3.Press PTT to save .
Voice Operated Transmission (Vox)
Transmisson is initiated by speaking into the microphone of the radio instead of the
pushing the PTT button.
Note: Note Level “N”(OFF)disables VOX Levels 1-3 set thesensitivity of the VOX circuit
Use level 1 in quiet environments, and use level 3 in very noisy environments. You can
find the appropriate sensitivity level by speaking into the microphone.
Scanning Channels
Eatures your radio to scan for active channels .when activity is detected, your radio
lands (stays) on that channel for 5 seconds. To transmit on that channel ends, your
radio continues scannig to other channels.
To turn the channel scan ON:
1.Press and hold to enter Scan mode.
2.press orPTT to turn off Scan mode.
Note:
During scanning , press the key to change the direction of the scan.
Safety and General Information
1.If you carry any kind of personal medical device, consult a doctor before use.
2.To avoid the risk of burns, do not use the device if the aerial is damaged in any way.
3.Never use the device in close proximity to a radio to avoid interference.
4.Position the transmitter and antenna at least 5 cm from your mouth.
5.The device cannot be used to contact the emergency services.
Interference Eliminator Code
Interference Eliminator Codes help minimize interference by providing you with a
choice of code combinations. To set the code for a channel:
1. Press until the code starts to flash.
2. Press to select the code 0-99 0R 99-0.
3. Press PTT to save the code setting.
You can set a different code for each channel using this procedure.
Note: You must set the Interference Eliminator Codes to 0 on an FRS radio that uses
Interference Eliminator Codes to communicate with other FRS radios that do not have
Interference Eliminator Codes.
TOT (TIME OUT Timer )
In order to prevent the use of the channel and save power, walkie-talkie has emission
limit function, then the launch time is less than 180 seconds.
When reached the default time , the radio stops launching with "beep" tone.
Locking the Keypad
To avoid accidentally changing your radio settings, pressfor 3 seconds or until
displays and there is a "beep" tone. You can turn the radio on and off, you can't adjust
the volume, menu, and monitor channels. All other functions are locked.
To unlock the radio, press for 3 seconds or until is no longer displayed. And
there is a “beep" tone.
Note: When locking , only the PTT and are valid.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group so you can
alert them that you want to talk.
5
76
4
Special Features
462.55000-467.71250MHz
446.00625-446.09375MHz
Web: www.hunicomtech.com
