Hunt CCTV HA0312OCT16 User manual

INSTRUCTION MANUAL Ver 1.4
Megapixel IP PTZ Camera
HA0312OCT16

Speed Dome Camera Instruction Manual 2/33
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL
This lightning flash with arrowhead symbol is intended to alert the user to
the presence of un-insulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
This Device compiles with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interface, and
(2) This device must accept any interference received, including
interference that may cause undesired operations.

Speed Dome Camera Instruction Manual 3/33
Important Safety Guide
1. Read, heed and follow all the Instructions
Read all the safety and operating instructions before using the product.
2. Keep this manual
Keep this manual for reference in future.
3. Attachments / Accessories
Use only the attachments or accessories specified by the manufacturer.
4. Installation
zDo not install near any heat resources such as radiators, heat registers, stoves, or other
appratus including amplifiers that product heat. Improperly installed product may fall,
cause serious injury to a child or adult and damage the product.
zDo not block any ventilation holes or openings. Install in accordance with the
manufacturer’s instructions.
zUse only with the cart, stand, tripod, bracket, mounting devices, or table specified by
the manufacturer.
zInstallation should be done only by qualified personnel and conform to all the
instructions by the manufacturer.
zRefer all servicing to qualified service personnel.
zUnless the product is specifically marked as IP67, more than IP67 or confirmed by the
manufacturer, it is designed for indoor use only and it must not be installed where
exposed to rain and moisture.
zDo not load on the product.
zUse stainless steel hardware to fasten the mount.
zTo prevent damage from water leakage when installing a mount outdoors on a roof or
wall, apply sealant properly around holes.
zThese servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other that contained in the
operationg instructions unless you are qualified to do so.
zUse only replacement parts specified by the manufacturer.
5. Power source
This product should be operated only from the type of the power source indicated on the
marking label.
NOTICE

Speed Dome Camera Instruction Manual 4/33
Caution
Operating
zBefore using, make sure that the power supply and others are properly installed.
zWhile operating, if any abnormal condition or malfunction is observed, stop using the
product immediately and then contact your local dealer.
Handling
zDo not disassemble or tamper with the parts inside the product.
zDo not drop or subject the product to shock and vibration as this can damage the
product.
zCare must be taken when you clean the clear dome cover. Especially, scratch and dust
will ruin the quality of the product.
Installation and Storage
zDo not install the product in areas of extreme temperature, which exceed the allowable
range.
zAvoid installing in humid or dusty places.
zAvoid installing in places where radiation is present.
zAvoid installing in places where there are strong magnetic fields and electric signals.
zAvoid installing in places where the product would be subject to strong vibrations.
NOTICE

Speed Dome Camera Instruction Manual 5/33
①Introduction
ModelCode 6
Features 7
Packa
g
e Com
p
onents 9
Main Part Descri
p
tion 11
②Installation
DIP Switch Setu
p
12
Installation with Ceilin
g
MountBracket 14
InstallationwithWallMountBracket 15
Installation with In-Ceilin
g
MountBracket 16
W
irin
g
and Cablin
g
17
③Operation
Check Point before O
p
eration 21
Check Points for Preset and Pattern Function before O
p
eration 21
Reserved Preset
(
Hot Ke
y
s
)
22
Preset 23
Swin
g
23
Pattern 24
Grou
p
24
④Specifications 25
Dimension 33
TABLE OF CONTENTS

Speed Dome Camera Instruction Manual 6/33
Model Code
HA-N20SW-S
N
P
Series
HA: Megapixel IP PTZ (Outdoor)
Video Signal
N: NTSC
P:PAL
Zoom
20S : Optical x20, 2Mega
18H : Optical x18, 1.3Mega
20T : Optical x20, 2Mega
19T : Optical x19, 1.3Mega
28L : Optical x28, 1.3Mega
30L : Optical x30, 2Mega
Mount Bracket
W: Wall Mount
C: Ceiling Mount
I: In-Ceiling Mount
Video Output
S: HD-SDI
C: CVBS(Composite Video)
PoE for IP model
P: PoE+
Blank : No PoE+
Network
N: H.264 IP Function
INTRODUCTION 1

Speed Dome Camera Instruction Manual 7/33
Featur es
Powerful Zoom Camera & Setup Options
zImage Sensor : 1/3" Exmor CMOS Image Sensor, 2 Mega pixels (20S model)
1/3" Solid State Progressive Scan CCD, 1.3 Mega pixels (18H model)
1/3" PS CMOS Image Sensor, 2 Mega pixels (20T model)
1/3" PS CMOS Image Sensor, 1.3 Mega pixels (19T model)
1/4" CMOS Image Sensor, 1.3 Mega pixels (28L model)
1/2.8" CMOS Image Sensor, 3 Mega pixels (30L model)
zZoom : ×20 Optical Zoom, ×12 Digital Zoom (20S model)
×18 Optical Zoom (18H model)
×20 Optical Zoom, ×8 Digital Zoom (20T model)
×19 Optical Zoom, ×16 Digital Zoom (19T model)
×28 Optical Zoom, ×12 Digital Zoom (28L model)
×30 Optical Zoom, ×12 Digital Zoom (30L model)
z Day & Night, Privacy Mask
z WDR function (20S, 18H, 28L, 30L model)
z HLC function (20T, 19T model)
Network Function over IP
zVideo Compression (H.264) & Audio Compression (G.711, AAC)
zDual Streaming over IP (H.264/H.264 or H.264/M-JPEG)
zRemote Access & Control via IP Network
Powerful Pan/Tilt Functions
zMAX. 360°/sec High Speed Pan/Tilt Motion
zWith the Vector Drive Technology, Pan/Tilt motions are accomplished along the
shortest path. As a result, the time to target view is remarkably short and the video on
the monitor is very natural in monitoring.
zWith the Micro-Stepping Control Technology, the video looks very natural at high
zoom magnification during a jog operation on a controller since the camera can be
controlled by 0.05°/sec. Hence it is very easy to make the camera focus on desired
target views at high zoom magnification. Additionally it is easy to make the camera
focus on desired positions with zoom-proportional pan/tilt movement.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 8/33
Preset, Pattern, Swing, Group, Privacy Mask and More…
zMAX. 128 Presets are programmable.
zMAX. 8 sets of Swing are programmable. This function is that a camera moves
repetitively between two preset positions at programmed speeds.
zMAX. 4 Patterns are programmable. This function is that a camera memorizes the path
(mostly curve path) by the joystick of the controller and revives the trajectory
operated by the joystick as closely as possible.
zMAX. 8 sets of Group are programmable. This function is that a camera memorizes the
combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern
and/or Swings repetitively. A Group can be combined upto 20 functions with any of
Preset/Pattern/Swing.
zMAX. 8 or 4 Privacy Masks are programmable, not to intrude on any other’s privacy.
PTZ(Pan/Tilt/Zoom) Control
zWith the RS-485 communication connection, MAX. 255 units of cameras can be
connected to a single controller.
zPelco-D or Pelco-P protocols can be selected as a control protocol in the current
firmware version.

Alarm In/Out Function
z2 alarm sensor inputs and 2 alarm sensor outputs are available.
zBoth of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used.
zThe camera can be set to move to a Preset position when there are external sensor
activations.
Rated Power
zDefault : DC 12V
zOption : PoE+ (PoE Model Only)

Perfect Outdoor Environment Compatibility and Easy Installation
zThe fans and heaters are built-in in the camera for cold and hot temperature
environment. Also idealistic mechanical design protects the camera from water and
dust. (IP67 when installed properly with wall mount bracket only / Only for outdoor
models)
zIt is easy to install and repair the camera.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 9/33
Package Component
Product & Accessories
zMain Body & Dome Cover (Wall/Ceiling model) zMain Body & Dome Cover (In
-
ceiling model)
zDefault Accessorie
s
[
Main Cable,Wrench,Cross LAN cable,Audio cable,C
D
]
INTRODUCTION 1

Speed Dome Camera Instruction Manual 10/33
Brackets (Optional)
zWall Mount Bracke
t
[Screws :TORX Machine M4×L18, Hex Lag
#14×50]
zCeiling Mount Bracke
t
[Screws :TORX Machine M4×L18, Anchor Bolt
3/8"×70]
zIn
-
Ceiling Moun
t
Bracke
t
[Screws:Tapping FH Ø4×L20, Machine Sams M3×L8]
INTRODUCTION 1

Speed Dome Camera Instruction Manual 11/33
Main Part Description
D
IP Switch IP Reset Switch
LAN Port
Audio Port
Main Connector
Dome Cover
Mountin
g
Scre
w
Hole
Drop Prevention Spring
BNC Connector
zDomeCover Do not detach the protection vinyl from the dome cover before
finishing all the installation process to protect the dome cover from
scratches or dust.
zDIP Switch Used to set u
p
camera IDs and
p
rotocols.
zDrop Prevention
Spring
This part keeps the camera from dropping during installation and
maintenance. After install the Bracket, please, hang the spring to
the drop prevention hook of main body as shown in picture for
further tasks.
zMountingScrewHole Used to assemble the main body with a bracket with screws.
zMain Connector Used for the power wire, sensor in/out and the RS-485
communication cable connection.
zBNC Connector Used for video si
g
nal connection.
zLA
N
Por
t
Used for Ethernet connection.
zAudio Por
t
Used for audio in/out connection.
zIP ResetSwitch Used to initialize all network configurations to the factory default.
Press the button for more than 5 seconds to initilze the network
confi
g
urations.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 12/33
DIP Switch Setup
Before installing the camera, set up the DIP switch to configure the camera ID and the
communication protocol.
Camera ID Setup
ON
ON
12345678
zID numbers of cameras are set up with binary numbers.
See the examples shown below.
Pin 12 3 4 5 6 7 8
BinaryValue 1 2 4 8 16 32 64 128
ex)ID=5 on of
f
on of
f
of
f
of
f
of
f
of
f
ex) ID=10 of
f
on of
f
on of
f
of
f
of
f
of
f
zThe camera ID range is “1~255”. Camera ID must not be
“0”!
zThe factory default of the camera ID is “1”.
zMatch the camera ID with the Cam ID setting of your DVR
or Controller to control the camera.
zIf you are connecting a single camera to a controller,
terminate the camera. When connecting more than one
camera to a single controller, terminate the last camera on
the communication line. The last camera means the camera
farthest in cable length from the controller.
zNote that the total length of the communication cable
between a controller and the camera(s) on the same
communication line must be less than 1.2Km.
INSTALLATION 2

Speed Dome Camera Instruction Manual 13/33
Communication Protocol Setup
1234
ON
ON
zSelect an appropriate Protocol with the DIP switch combination.
Switch Mode
Protocol
P0
(Pin 1) P1 (Pin 2) P2 (Pin 3)
OFF OFF OFF PELCO-D, 2400 bps
ON OFF OFF PELCO-D, 9600 bps
OFF ON OFF PELCO-P, 4800 bps
ON ON OFF PELCO-P, 9600 bps
Others Reserved
zMatch the camera protocol with the camera protocol in the setting of
your DVR or controller to control the camera.
zAdjust the DIP switch after turning off the camera. If you changed the
camera protocol by changing the DIP S/W, the change will be effective
after you reboot the camera.
zThe factory default protocol is “Pelco-D, 2400 bps”.
INSTALLATION 2

Speed Dome Camera Instruction Manual 14/33
Installation with Ceiling Mount Bracket
①
Remove the ceiling tile from the ceiling
and cut a hole whose diameter is
30~40mm on the ceiling tile to pass the
wire(s) and cable(s) through to the upside
of the ceiling. (In case of the wiring and
cabling through the mounting surface
only) Then prepare the ceiling mount
bracket. Pull the wire(s) for the system as
below. (Anchor Bolt 3/8"×70)
②
Hook up “Drop Prevention Spring
”
on
main body to prevent camera from
unexpected drop and pull the wire(s) and
cable(s) for the system as below.
③
Line up the mold lines and assemble
main body to mount adaptor and turn it.
And assemble the main both with the
camera mount adaptor with the 3 screws.
(TORX SCREW M4×18).
④
Screw the dome cover to the main body
and remove the protection vinyl from the
dome cover.
Important Notice
zBefore starting the installation,make sure that the Camera ID and Protocol are set up properly.
zTo adjust the installation height from the mounting surface, the pipe and coupler should be needed
between the surface mount part of the ceiling mount bracket and the camera mount part of the ceiling
mount bracket.Note that they are not supplied by the manufacturer.
INSTALLATION 2

Speed Dome Camera Instruction Manual 15/33
Installation with Wall Mount Bracket
①
Make a hole whose diameter is 30~40mm
on the mounting surface to pass the
wire(s) and cable(s) through the mounting
surface. (In case of the wiring and cabling
through the mounting surface only) Then
prepare the wall mount bracket. Pull the
wire(s) and cable(s) for the system as
below. Attach the wall mount bracket to
the mounting surface. (Hex Lag #14×50)
②
Hook up “Drop Prevention Spring
”
on
main body to prevent camera from
unexpected drop and pull the wire(s) and
cable(s) for the system as below.
③
Line up the mold lines and assemble
main body to mount adaptor and turn it.
And assemble the main both with the
camera mount adaptor with the 3 screws.
(TORX SCREW M4×18).
④
Screw the dome cover to the main body
and remove the protection vinyl from the
dome cover.
Important Notice
zBefore starting the installation,make sure that the Camera ID and Protocol are set up properly.
INSTALLATION 2

Speed Dome Camera Instruction Manual 16/33
Installation with In-ceiling Bracket
①
Assemble the dome cover and the braket
with the main body
②Cut a hole whose diameter is 215mm on
the ceiling tile and insert the camera into
the hole. Open the cover and make all the
connections.
215
③
Install the ceiling tile to the ceiling. Fix
the camera to the ceiling tile with the
Guide Hook Screws.
④
Assemble the Deco-Rin
g
with the camera by
spinning.
Important Notice
zBefore starting the installation,make sure that the Camera ID and Protocol are set up properly.
INSTALLATION 2

Speed Dome Camera Instruction Manual 17/33
W
iring and Cabling
BROWSER
POWER
CONTROLLER / DVR
IR
SENSOR
DOOR
SWITCH
RS-485
SENSOR I/O
LAN CABLE
AUDIO
CABLE
MAIN CABLE
BNC CABLE
MONITOR
INTERNET
MIC SPEAKER
Port Description
zMain Cable
Port Pin Number
W
ire Color Si
g
nal
1 Black RS-485 +
2 Brown RS-485 -
3 Red DC 12V
4 Oran
g
eGND
5
Y
ellow OUT COM
(
Rela
y
Out
p
ut Common
)
6 Green OUT 2
(
Rela
y
Out
p
ut 2
)
7 Blue OUT 1
(
Rela
y
Out
p
ut 1
)
8
V
iolet IN COM
(
Sensor In
p
ut Common
)
9 Gra
y
IN 1
(
Sensor In
p
ut 1
)
10
W
hite IN 2
(
Sensor In
p
ut 2
)
zAudio Cable
Port Pin Number Connector / Wire Color Si
g
nal
1 RCA
(
Ye l l ow
)
Audio IN
2 Audio GND
3 RCA
(
White
)
Audio OUT
INSTALLATION 2

Speed Dome Camera Instruction Manual 18/33
Power Description
zCarefully check the voltage and current capacity of the rated power.
In
p
utVolta
g
e Ran
g
eCurrent Consum
p
tion
DC 11V ~ 18V 2.0 A
zFor the DC input, be careful with the polarity of DC power. The system should be
permanentally damaged by wrong DC input.
zIn case that the length of the power wire is very long, there may be voltage drop and the
syatem may not work properly. Make the length of the power wire as short as possible.
zWhen the rated power input is PoE+(High PoE), make connections only with the
equipments whose rated power is PoE+(30W). (PoE+ 802.3aT)

RS-485 Communication
zFor PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple
cameras to a single controller, RS-485 communication should be connected in parallel as
shown below. If you are connecting a single camera to a controller, terminate the camera.
When connecting more than one camera to a single controller, terminate the last camera
on the communication line. The last camera means the camera farthest in cable length
from the controller. Note that the total length of the communication cable between a
controller and the camera(s) on the same communication line must be less than 1.2Km.
INSTALLATION 2
CONTROLLER / DVR
RS-485
+
-
#1
+
-
#2
+
-
#n
+
-

Speed Dome Camera Instruction Manual 19/33
Video (HD-SDI or CBVS)
zUse BNC coaxial cable only.
zTransmission Distance of HD-SDI Video Signal should be variable by cables. There may
be no video on a monitor due to cable quality or specification. Use proper BNC Coaxial
Cables after considering transmission distance.
zFor your reference, see the below table. It shows transmission distances by cables.
Cable Type Transmission Distance
RG11 14AWG 330 Meter
Belden 1694A 18AWG 230 Meter
RG6 18AWG (5C-HFBT) 210 Meter
RG59 20AWG 150 Meter
RG59 23AWG 110 Meter
3C2V 25AWG 90 Meter
INSTALLATION 2

Speed Dome Camera Instruction Manual 20/33
Alarm Input
Sensor Input is detected by Short or Open between Sensor IN Terminal and COMMON
Terminal.
If you want to use Alarm Input, the types of sensors must be selected. The sensor types
are divided into Normal Open and Normal Close. If wrong sensor types are selected,
alarms should be activated reversely to sensor inputs.
~Normal Open A sensor activates when a Sensor IN Terminal and COMMON
Terminal are Short
~Normal Close A sensor activates when a Sensor IN Terminal and COMMON
Terminal are Open
Relay Output
OUT 1
AC or DC
LOAD
INTERNAL
OUT 2
LOAD
OUT COM
The maximum loads are as follows.
Power Type DC Power AC Power
Maximum Load MAX. DC 24V, 1A MAX. AC 125V, 0.5A
IN COM
IN 1
IN 2
Sensor 1
Sensor 2
V+
INSTALLATION 2