Hunt HTC-65C User manual

HTC-65GNV HIGH RESOLUTION
HTC-65CNV MED. RESOLUTION DAY&NIGHT CCD CAMERA
SPECIFICATOINS
ITEM NO. HTC-65C HTC-65G
PICK UP DEVICE CCD IMAGE SENSOR 1/3”
ELEMENTS H*V NTSC: 512*492—PAL: 512*582 NTSC: 771*492—PAL: 753*582
HORIZONTAL RESOLUTION Morethan400TV LinesMorethan 540TV Lines
SYNCHRO FREQUENCY NTSC: 15.734 kHz – PAL: 15.625 kHz
CLOCK FREQUENCY NTSC: 59.94Hz – PAL: 50Hz
SCANNING SYSTEM 2 : 1 INTERLANCE
SENSITIVITY D/N 1/0.05 Lux F=1.2 2/ 0.08 Lux F=1.2
SYNCHRONIZATION LINE LOCK
S/N RATIO MORE THAN 50 dB (AGC Auto)
VIDEO OUTPUT 1 Vpp, 75 Ohms Composite
AUTO IRIS Video Driver / DC Driver Switchable
MOUNT LENS CS Mount
POWERSUPPLY24VAC or 12VDC (±10%)
POWER CONSUMPTION 3.5W for 24VAC 4W for 24VAC
AES(ELECTRONIC SHUTTER) Up to 1/100,000 sec. (linear) ON/OFF Switchable
D/N (day & night) Normal image, Day & night ON/OFF Switchable
IR RAY (acceptable) 850～940nM INFREDRAD WAVE LENGTH
DIMENSIONS (mm) 102 (D) * 59 (W) * 59 (H)
WEIGHT (g) 430
STORAGE TEMPERATURE -30 to + 60 Degree C
OPERATON TEMPERATURE -10 to + 45 Degree C
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
CAUTIONS
1. In order to protect the camera, avoid placing or using it under direct sunlight, rain or dust.
2. Don't touch the CCD sensor directly with your fingers. If necessary, use soft cloth moistened with alcohol to wipe off the
dust.
3. When the camera is not in use, keep the lens, or cap being attached to protect the CCD sensor.
4. DC model: use a + 12V regulated power source.
AC model: directly connect to AC power source.
5. Don’t drop your camera or give it a strong shock or vibration.
CONNECTION
1. Before connection, make sure that power of all units are OFF and cords are unplugged.
2. Mount a lens onto the camera.
3. Connect a video terminal of the camera and the video input terminal of a monitor TV
with a 75 Ωcoaxial cable.
4. Connect the power terminal of the camera to a power supply.
Caution:
* Installation should conform to all local codes.
* Lens, coaxial cable for video signal and power supply are not supplied with the camera.
LOCATIONS、FUNCTION OF PARTS & ACCESSORIES
STEP
Attach the Lens
Connect to a monitor TV
Connect a
p
ower source
Adjust the focus
Adjust the back focus

. OPERATIONS AND ADJUSTMENTS
1. Connect the power cord and turn the power ON.
2. Adjust the iris and focus of the lens to obtain the optimum image.
* Using normal lenses
CS-mount lens mode is the standard type. When use C-mount lens,
Please use the CS-C conversion Ring.
* Using the zoom lens (adjustment of the back focus)
The camera is set at the standard back focus position when shipped from factory.
Depending on types of zoom lenses, however slight adjustment may be necessary.
Adjust the lens back-focus by turning the focusing knob in either direction.
(1) Place an object at any fixed distance and set the focus ring
of the zoom lens to be used with.
(2) Set the zoom lens to fully TELE position and obtain the best focus
position by turning the focus ring of the zoom.
(3) Then set the zoom lens to fully WIDE position and obtain the best
focus position by turning the focusing knob.
(4) Repeat the procedures 2 and 3 until focus remains in constant among
the zoom range.
* Using an auto iris lens
NOTE: Don't use both SHUTTER ON & AUTO IRIS lens at the same time.
(DC driver lens)
When auto iris lens is used, set AI DRIVER switch to DC position
and connect the plug of the lens (for iris terminal) to the IRIS
terminal on the back of camera.
DC Drive Level
When you use an DC Driver Lens you can adjust the
DC Drive Level for the bright of video output.
(Video Driver lens)
When auto iris is used,
AI DRIVER switch to VIDEO position and
to connect the plug of the lens (for iris terminal)
to the IRIS terminal on the back of the camera.
Dip Switch
1. BLC (BACK LIGHT COMPENSATION)
As you take a picture with strong light behind the subject, the picture would be looked very dim on the subject. In this
case, you should select BLC ON to get a clear image.
NOTE: When you select BLC ON than the SHUTTER should be in ON position or use Auto Iris Lens.
2. AES
By setting the AES switch to ON, the AES mode (Up to 1/100,000) sec) is available.
For shooting fast-moving objects or high brightness environment, the various electronic shutter speed can change
automatically.
3. D/N
By setting the switch to ON, the image is normal situation. If you choose switch to OFF, color image would change to
black and white automatically under low light condition.
SWITCH (ON) ON OFF USAGE
1. BLC YES NO BACK LIGHT COMPENSATION
2. AES YES NO WHEN NOT USE THE IRIS LENS
3. D/N NORMAL DAY & NIGHT COLOR IMAGE WOULD CHANGE TO B/W
IMAGE UNDER LOW LIGHT CONDITION.
LINE LOCK
When two or more cameras are switched by the video switcher, quad or multiplexer for monitoring on a TV monitor. The
picture may fluctuate due to different AC line phase of each camera, In this case, please select the Line Lock function.